P1442 Stuck Close in Secondary Air Injection Vacuum Switching Valve Bank 1
Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011
Also covers:
- P1445 Stuck Close in Secondary Air Injection Vacuum Switching Valve Bank 2
- P2441 Secondary Air Injection System Switching Valve Stuck Close Bank1
DESCRIPTION
The diagnostic trouble code (DTC) indicates that the electric air switching valve (E-ASV) and air switching valves (ASVs) of the secondary air injection (AIR) system are stuck closed. The engine control module (ECM) operates entire components of this system in a sequence, and monitors the system pressure and exhaust pulse (AIR monitor). This monitor will run just after a cold engine start. If abnormal pressure and exhaust pulse are detected, the ECM interprets this as a malfunction. When the malfunction is detected in consecutive driving cycles, the ECM illuminates the malfunction indicator lamp (MIL), and stores a DTC.The secondary air injection (AIR) system introduces fresh air into the exhaust manifold in order to reduce carbon monoxide (CO) and hydrocarbon (HC) in the exhaust emission. This system is activated just after engine start, and is stopped when the catalyst converter is warmed-up. This system consists of the following components: 1) the air pump which sends fresh air to the exhaust manifold, 2) the electric air switching valve (E-ASV) which switches the fresh air flow, 3) the air switching valve (ASV) which switches the air passage to the exhaust manifold of each bank, 4) the vacuum switching valve (VSV) which switches the vacuum (intake manifold pressure) to operate the ASV, 5) the pressure sensor which detects the fresh air pressure and exhaust pulse, 6) the air injection control driver which controls the power sources of the air pump and E-ASV, 7) the engine control module (ECM) which controls and monitors this system.


Reference 1: Operation of each component during AIR monitor


| Time A [Pressure Change] |
Time B [Pressure Change] |
Time C [See Chart Below] |
Time D [Exhaust Pulse] |
Time E [Exhaust Pulse] |
Time F [See Chart Below] |
DTC |
| Yes |
Yes |
Pattern 1 |
- |
No |
Pattern 4 |
Normal |
| Yes |
No |
Pattern 1 |
Yes |
No |
Pattern 4 |
|
| No |
Yes |
Pattern 1 |
- |
No |
Pattern 3 |
P1442 P1445 P2444 |
| Yes |
No |
Pattern 1 |
No |
No |
Pattern 3 |
|
| Yes |
No |
Pattern 1 |
No |
No |
Pattern 4 |
P1442 P1445 |
| No |
Yes |
Pattern 1 |
- |
No |
Pattern 4 |
|
| No |
No |
Pattern 1 |
Yes |
No |
Pattern 4 |
|
| No |
No |
Pattern 1 |
No |
No |
Pattern 4 |
|
| No |
No |
Pattern 3 |
No |
No |
Pattern 3 |
P1442 P1445 P2441 P2444 |
| No |
No |
Pattern 3 |
No |
No |
Pattern 4 |
P1442 P1445 P2441 |
| Pattern |
System Pressure |
Exhaust Pulse |
| 1 |
High |
Yes |
| 2 |
Low |
Yes |
| 3 |
High |
No |
| 4 |
Low |
No |
| DTC Code |
DTC Detection Condition |
Trouble Area |
| P1442 |
The ASV (bank 1) is stuck closed (2 trip detection logic). |
|
| P1445 |
The ASV (bank 2) is stuck closed (2 trip detection logic). |
|
| P2441 |
The E-ASV is stuck closed (2 trip detection logic). |
|
WIRING DIAGRAM
Refer to DTC P0412 (Click here).INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. PERFORM SECONDARY AIR INJECTION SYSTEM CHECK (AUTOMATIC MODE) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester on.
Record the DTCs and freeze frame data.
Clear the DTCs.
Warm-up the engine.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check (Automatic Mode).
Perform the Active Test and check the pending DTC.
Result Result
Proceed to
P1442, P1445 and/or P2441 is output
A
DTC other than P1442, P1445 and/or P2441 are output
B
No DTC is output
C
|
|
||||
|
|
||||
| A | |
| 2. CHECK VACUUM HOSES (VSV) |
![]() ![]() |
Check that the vacuum hoses between the throttle body and VSV for the secondary air injection system are securely connected.
- OK:
- The vacuum hoses are securely connected.
Inspect the vacuum hoses for blockages or damage.
- OK:
- The vacuum hoses have no blockages or damage.
|
|
||||
| OK | |
| 3. CHECK VACUUM SWITCHING VALVE (VSV) |
![]() ![]() |
Turn the engine switch off.
Disconnect the vacuum hoses from the VSV for the secondary air injection system.
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Perform the Active Test to operate the secondary air injection system, and check that there is negative pressure from ports A. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check (Manual Mode) / Operation 5 or 6.
- OK:
- Negative pressure from ports A.
- NOTICE:
- This test only allows technicians to operate the AIR system for 5 seconds. Furthermore, the test can be performed 4 times a trip. If the test is repeated, intervals of at least 30 seconds are required between tests.
While the AIR system operation using the intelligent tester is prohibited, the tester displays the prohibition (WAIT or ERROR). If ERROR (AI Status NG) is displayed on the tester, stop the engine for 10 minutes and then try again.
- When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the engine switch turned on (IG) or the engine running.
- Turn the engine switch off when the Secondary Air Injection Check operation finishes.
- This test only allows technicians to operate the AIR system for 5 seconds. Furthermore, the test can be performed 4 times a trip. If the test is repeated, intervals of at least 30 seconds are required between tests.
|
|
||||
| OK | |
| 4. CHECK VACUUM HOSES (AIR SWITCHING VALVE) |
![]() ![]() |
Check that the vacuum hoses between the air switching valve(s) and VSV for the secondary air injection system are securely connected.
- OK:
- The vacuum hose(s) are securely connected.
Check the vacuum hoses for blockages and damage.
- OK:
- The vacuum hoses have no blockages or damage.
|
|
||||
| OK | |
| 5. CHECK PIPES AND HOSES |
![]() ![]() |
Remove the intake manifold (Click here).
Check all pipes and hoses of the secondary air injection system.
- OK:
- All air injection pipes and hoses are securely connected.
Check all pipes and hoses for blockage or damage.
- OK:
- All air injection pipes and hoses have no blockages or damage.
|
|
||||
| OK | |
| 6. CHECK AIR SWITCHING VALVE (OPERATION) |
![]() ![]() ![]() ![]() |
Remove the intake manifold (Click here).
Remove the Air Switching Valve (ASV).
Blow air into port A and check that air is not discharged from port B.
Apply battery positive voltage across the terminals.
Blow air into port A and check that air is discharged from port B.
- OK:
Tester Connection
Condition
Specified Condition
port A - port B
Always
Not discharged
port A - port B
Battery positive voltage applied
Discharged
|
|
||||
| OK | ||
| ||






