Cranking Holding Function Circuit
Circuit diagnosis · Vehicles built from Jan 2012
DESCRIPTION
The cranking holding control system provides current to the starter when the ECM detects the engine switch start signal (STSW). When the ECM performs a firing judgment, the system cuts current to the starter. When an ECM receives the STSW signal, it turns on the ST CUT relay, which prevents flickering of the combination meter, clock, audio system, etc. Also, the ECM sends a signal to the ECM STAR terminal of the ECM. Then the STAR output signal travels through the park/neutral position (PNP) switch to the ST relay, causing the starter to activate.When the engine is cranking, the starter operation signal is sent to the ECM STA terminal of the ECM.


WIRING DIAGRAM
Refer to DTC P0617 (Click here).INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
| 1. CHECK CRANKING |
Check the cranking of the engine.
- Result:
Test Result
Proceed to
Cranking possible and holding control operates
A
Does not crank
B
Cranking possible but holding control does not operate
C
|
|
||||
|
|
||||
| A | ||
| ||
| 2. READ VALUE USING GTS (STARTER SIGNAL) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
Read the values.
Check the result when the engine switch is turned on (IG) and when the engine is started.
- OK:
Engine Switch Condition
Display (Starter Signal)
On (IG)
Close
Engine started
Open
|
|
||||
| OK | |
| 3. INSPECT STARTER RELAY (ST) |
Inspect the starter relay (ST) (Click here).
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (PNP SWITCH - ST RELAY) |


Disconnect the Park/Neutral Position (PNP) switch.
Remove the ST relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
ST relay (1) - C24-5
Always
Below 1 Ω
ST relay (1) or D24-5 - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (POWER SOURCE) |
![]() ![]() |
Remove the ST relay from the engine room relay block.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
ST relay (2) - ST relay (5)
Always
11 to 14 V
|
|
||||
| OK | |
| 6. INSPECT STARTER |
Inspect the starter (Click here).
- Result:
Test Result
Proceed to
OK
A
NG
B
|
|
||||
| A | ||
| ||
| 7. INSPECT STARTER CUT RELAY (ST CUT) |
Inspect the starter cut relay (ST CUT) (Click here).
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (ST CUT RELAY - PNP SWITCH, ECM) |
![]() ![]() |
Remove the starter cut relay (ST CUT) from the engine room relay block.
Disconnect the PNP switch connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for LHD Tester Connection
Condition
Specified Condition
ST CUT relay (5) - C45-52 (STAR)
Always
Below 1 Ω
ST CUT relay (3) - C24-4
Always
Below 1 Ω
ST CUT relay (5) or C45-52 (STAR) - Body ground
Always
10 kΩ or higher
ST CUT relay (3) or C24-4 - Body ground
Always
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
ST CUT relay (5) - C46-52 (STAR)
Always
Below 1 Ω
ST CUT relay (3) - C24-4
Always
Below 1 Ω
ST CUT relay (5) or C46-52 (STAR) - Body ground
Always
10 kΩ or higher
ST CUT relay (3) or C24-4 - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 9. INSPECT PARK/NEUTRAL POSITION SWITCH |
Inspect the Park/Neutral Position (PNP) switch.

Disconnect the PNP switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
4 (B) - 5 (L)
Shift lever in P
Below 1 Ω
Shift lever in N
Below 1 Ω
|
|
||||
| OK | |
| 10. CHECK HARNESS AND CONNECTOR (PNP SWITCH - ECM) |
![]() ![]() |
Disconnect the PNP switch connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for LHD Tester Connection
Condition
Specified Condition
C24-5 - A38-46 (STA)
Always
Below 1 Ω
C24-5 or A38-46 (STA) - Body ground
Always
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
C24-5 - A52-46 (STA)
Always
Below 1 Ω
C24-5 or A52-46 (STA) - Body ground
Always
10 kΩ or higher
Result Result
Proceed to
NG
A
OK
B
|
|
||||
| A | ||
| ||
| 11. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ECM) |


Disconnect the main body ECU connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for LHD Tester Connection
Condition
Specified Condition
E4-4 (STSW) - A38-47 (STSW)
Always
Below 1 Ω
E4-4 (STSW) or A38-47 (STSW) - Body ground
Always
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
E4-4 (STSW) - A52-47 (STSW)
Always
Below 1 Ω
E4-4 (STSW) or A52-47 (STSW) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 12. CHECK HARNESS AND CONNECTOR (ST CUT RELAY - PNP SWITCH, ECM) |
![]() ![]() |
Remove the starter cut relay (ST CUT) from the engine room relay block.
Disconnect the PNP switch connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for LHD Tester Connection
Condition
Specified Condition
ST CUT relay (5) - C45-52 (STAR)
Always
Below 1 Ω
ST CUT relay (3) - C24-4
Always
Below 1 Ω
ST CUT relay (5) or C45-52 (STAR) - Body ground
Always
10 kΩ or higher
ST CUT relay (3) or C24-4 - Body ground
Always
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
ST CUT relay (5) - C46-52 (STAR)
Always
Below 1 Ω
ST CUT relay (3) - C24-4
Always
Below 1 Ω
ST CUT relay (5) or C46-52 (STAR) - Body ground
Always
10 kΩ or higher
ST CUT relay (3) or C24-4 - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 13. REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 14. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Check the starter operation.
- OK:
- Malfunction has been repaired successfully.
|
|
||||
| OK | ||
| ||



