2011-2013 Land Cruiser · Service Manual Brake

C1232/32 Stuck in Deceleration Sensor

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

DESCRIPTION

The skid control ECU receives signals from the yaw rate and G sensor via the CAN communication system.
The yaw rate sensor has a built-in G sensor.
If there is trouble in the bus lines between the yaw rate and G sensor and the CAN communication system, the DTCs U0123/62 (yaw rate sensor communication trouble) and U0124/95 (G sensor communication trouble) are stored.
DTC Code
DTC Detection Condition
Trouble Area
C1232/32
At a vehicle speed of 10 km/h (6 mph) or more, the fluctuation range of the signal from one of either GL1 or GL2 is below 80 mV and the fluctuation range of the signal of the other is higher than 1.9 V for 30 seconds or more.
  1. Yaw rate and G sensor
  2. Harness or connector
  3. CAN communication system
C1234/34
A sensor malfunction signal is received from the yaw rate sensor.
  1. Yaw rate and G sensor
  2. Harness or connector
  3. CAN communication system
C1243/43
The following condition repeats 16 times.
  1. GL1 and GL2 do not change when the vehicle decelerates from 30 km/h (19 mph) to 0 km/h (0 mph).
  1. Yaw rate and G sensor
  2. Harness or connector
  3. CAN communication system
C1244/44
When either of the following conditions is detected:
1. Both of the following conditions continue for at least 60 seconds.
  1. The vehicle is stopped.
  2. The difference between GL1 and GL2 does not drop less than 0.4 G after it reaches 0.6 G or more.
2. A data malfunction signal is received from the G sensor.
  1. Yaw rate and G sensor
  2. Harness or connector
  3. CAN communication system
C1245/45
The following condition continues for at least 60 seconds.
  1. The difference between the values calculated from the G sensor value and vehicle speed exceeds 0.35 G.
  1. Yaw rate and G sensor
  2. Harness or connector
  3. CAN communication system
C1381/97
A G sensor power source malfunction signal is received for at least 10 seconds at a speed of more than 3 km/h (2 mph).
  1. Yaw rate and G sensor
  2. Harness or connector
  3. CAN communication system

WIRING DIAGRAM

C173288E01

INSPECTION PROCEDURE

NOTICE:
When replacing the yaw rate and G sensor, perform zero point calibration (Click here).


1. CHECK DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON.

  1. Check if the DTCs (U0073/94, U0123/62, C1210/36 and/or C1336/98) are output (Click here).

    Result 
    Result
    Proceed to
    DTC U0073/94, U0123/62, C1210/36 and/or C1336/98 are not output
    A
    DTC U0073/94 and/or U0123/62 are output
    for LHD
    B
    for RHD
    C
    DTC C1210/36 and/or C1336/98 are output
    D



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

D
REPAIR CIRCUIT INDICATED BY OUTPUT DTC (Click here)
A


2. CHECK YAW RATE AND G SENSOR INSTALLATION
  1. Check that the yaw rate and G sensor is installed properly.

    OK:
    The sensor is tightened to the specified torque. The sensor is not tilted.



NG
INSTALL YAW RATE AND G SENSOR CORRECTLY (Click here)
OK


3. INSPECT YAW RATE AND G SENSOR (IG AND GND TERMINAL)

  1. A115666E46
    Disconnect the E50 yaw rate and G sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E50-4 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E50-1 (GND) - Body ground
    Always
    Below 1 Ω

    Result 
    Result
    Proceed to
    OK (When troubleshooting in accordance with the Diagnostic Trouble Code Chart)
    A
    OK (When troubleshooting in accordance with the Problem Symptoms Table)
    B
    NG
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE YAW RATE AND G SENSOR (Click here)


← C1232 Acceleration Sensor Stuck Malfunction (+ C1243, C1245, C1279) (from Jan 2012)C1241 Low Power Supply Voltage Malfunction (from Jan 2012) →