Open in One Side of CAN Branch Line
Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
If 2 or more ECUs and/or sensors do not appear on the intelligent tester "Bus Check" screen, one side of the CAN branch wire may be open (One side of the CANH [branch wire]/CANL [branch wire] of the ECU and/or sensor is open).| Symptom |
Trouble Area |
| 2 or more ECUs and/or sensors do not appear on the intelligent tester "Bus Check" screen. |
|
- *1: w/ Navigation System
- *2: w/ Airbag System
- *3: w/ Network Gateway ECU
- *4: w/o Network Gateway ECU
WIRING DIAGRAM








INSPECTION PROCEDURE
- HINT:
- Perform the following inspection for the ECUs (sensors) which are not displayed on the intelligent tester. If a malfunction cannot be identified, perform the following inspections for the ECUs (sensors) connected to the CAN communication system.
- Perform the following inspection for the ECUs (sensors) which are not displayed on the intelligent tester. If a malfunction cannot be identified, perform the following inspections for the ECUs (sensors) connected to the CAN communication system.
- Do not remove the combination meter and ECM, as they are the end parts of the circuit. If removed, CAN communication will not be possible.
- Do not remove the combination meter and ECM, as they are the end parts of the circuit. If removed, CAN communication will not be possible.
- The open circuit confirmation of the combination meter, ECM and main wire is performed in the Check CAN Bus Line procedure of How to Proceed with Troubleshooting. This inspection only has procedures for checking for an open circuit on one side of the CAN branch wire.
- The open circuit confirmation of the combination meter, ECM and main wire is performed in the Check CAN Bus Line procedure of How to Proceed with Troubleshooting. This inspection only has procedures for checking for an open circuit on one side of the CAN branch wire.
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.
- CAUTION:
- For vehicles with an SRS system:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| NEXT | |
| 2. CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (DISPLAY AND NAVIGATION MODULE DISPLAY) |
- NOTICE:
- For vehicles without the navigation system, go to "Check for Open in One Side of Branch Wire (Center Airbag Sensor)".
Disconnect the F64 display and navigation module display connector.
Select "Bus Check" on the intelligent tester (Click here).
Result Result
Proceed to
"Display and Navigation (AVN)" not displayed on intelligent tester.
A
Several ECUs and sensors other than "Display and Navigation (AVN)" not displayed on intelligent tester.
B
|
|
||||
| A | |
| 3. CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (DISPLAY AND NAVIGATION MODULE DISPLAY BRANCH WIRE) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
F64-21 (CANH) - F64-22 (CANL)
Ignition switch off
54 to 69 Ω
Text in Illustration *1
Front view of wire harness connector
(to Display and Navigation Module Display)
|
|
||||
| OK | ||
| ||
| 4. CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (CENTER AIRBAG SENSOR) |
- NOTICE:
- For vehicles without the airbag system, go to "Check for Open in One Side of Branch Wire (Air Conditioning Amplifier)".
Disconnect the E47 center airbag sensor connector.
Select "Bus Check" on the intelligent tester (Click here).
Result Result
Proceed to
"Airbag" not displayed on intelligent tester.
A
Several ECUs and sensors other than "Airbag" not displayed on intelligent tester.
B
|
|
||||
| A | |
| 5. CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (CENTER AIRBAG SENSOR BRANCH WIRE) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E47-13 (CANH) - E47-22 (CANL)
Ignition switch off
54 to 69 Ω
Text in Illustration *1
Front view of wire harness connector
(to Center Airbag Sensor)
|
|
||||
| OK | ||
| ||
| 6. CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (AIR CONDITIONING AMPLIFIER) |
Disconnect the E35*1 or E81*2 air conditioning amplifier connector.*1: w/ Rear Air Conditioning System*2: w/o Rear Air Conditioning System
Select "Bus Check" on the intelligent tester (Click here).
Result Result
Proceed to
"Air Conditioning Amplifier" not displayed on intelligent tester.
A
Several ECUs and sensors other than "Air Conditioning Amplifier" not displayed on intelligent tester.
B
|
|
||||
| A | |
| 7. CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (AIR CONDITIONING AMPLIFIER BRANCH WIRE) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
w/ Rear Air Conditioning System Tester Connection
Switch Condition
Specified Condition
E35-3 (CANH) - E35-4 (CANL)
Ignition switch off
54 to 69 Ω
w/o Rear Air Conditioning System Tester Connection
Switch Condition
Specified Condition
E81-11 (CANH) - E81-12 (CANL)
Ignition switch off
54 to 69 Ω
Text in Illustration *A
w/ Rear Air Conditioning System
*B
w/o Rear Air Conditioning System
*1
Front view of wire harness connector
(to Air Conditioning Amplifier)
|
|
||||
| OK | ||
| ||
| 8. CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (MAIN BODY ECU) |
Disconnect the E3 main body ECU (cowl side junction block LH) connector.
Select "Bus Check" on the intelligent tester (Click here).
Result Result
Proceed to
"Main Body" not displayed on intelligent tester.
A
Several ECUs and sensors other than "Main Body" not displayed on intelligent tester.
B
|
|
||||
| A | |
| 9. CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (MAIN BODY ECU BRANCH WIRE) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E3-5 (CANH) - E3-6 (CANL)
Ignition switch off
54 to 69 Ω
Text in Illustration *1
Rear view of wire harness connector
(to Main Body ECU)
|
|
||||
| OK | ||
| ||
| 10. SYSTEM CHECK |
Check the vehicle specifications.
Result Result
Proceed to
w/ Network Gateway ECU
A
w/o Network Gateway ECU
B
|
|
||||
| A | |
| 11. CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (NETWORK GATEWAY ECU BRANCH WIRE) |
Disconnect the E31 network gateway ECU connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E31-16 (CA1H) - E31-15 (CA1L)
Ignition switch off
54 to 69 Ω
Text in Illustration *1
Front view of wire harness connector
(to Network Gateway ECU)
|
|
||||
| OK | ||
| ||
| 12. CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (CLEARANCE WARNING ECU) |
- NOTICE:
- For vehicles without the TOYOTA parking assist-sensor system, go to "Check for Open in One Side of Branch Wire (4WD Control ECU)".
Disconnect the F12 clearance warning ECU connector.
Select "Bus Check" on the intelligent tester (Click here).
Result Result
Proceed to
"Clearance Warning (Clearance Sonar)" not displayed on intelligent tester.
A
Several ECUs and sensors other than "Clearance Warning (Clearance Sonar)" not displayed on intelligent tester.
B
|
|
||||
| A | |
| 13. CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (CLEARANCE WARNING ECU) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
F12-3 (CANH) - F12-5 (CANL)
Ignition switch off
54 to 69 Ω
Text in Illustration *1
Front view of wire harness connector
(to Clearance Warning ECU)
|
|
||||
| OK | ||
| ||
| 14. CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (4WD CONTROL ECU) |
Disconnect the A27 4WD control ECU connector.
Select "Bus Check" on the intelligent tester (Click here).
Result Result
Proceed to
"Four Wheel Drive Control" not displayed on intelligent tester.
A
Several ECUs and sensors other than "Four Wheel Drive Control" not displayed on intelligent tester.
B
|
|
||||
| A | |
| 15. CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (4WD CONTROL ECU) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
A27-19 (CAN+) - A27-20 (CAN-)
Ignition switch off
54 to 69 Ω
Text in Illustration *1
Front view of wire harness connector
(to 4WD Control ECU)
|
|
||||
| OK | ||
| ||
| 16. CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (SKID CONTROL ECU) |
Disconnect the A24 master cylinder solenoid (skid control ECU) connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
A24-11 (CANH) - A24-25 (CANL)
Ignition switch off
54 to 69 Ω
Text in Illustration *1
Front view of wire harness connector
(to Master Cylinder Solenoid [Skid Control ECU])
|
|
||||
| OK | ||
| ||
