2011-2013 Land Cruiser · Service Manual Power Source / Network

Short to GND in CAN Bus Line

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

There may be a short circuit between the CAN bus lines and GND when the resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.
Symptom
Trouble Area
The resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.
  1. Short between CAN bus lines and GND
  2. ECM
  3. Center airbag sensor assembly*1
  4. Headlight swivel ECU assembly*2
  5. Multi-media module receiver assembly*3
  6. Air conditioning amplifier assembly
  7. Main body ECU (cowl side junction block LH)
  8. Network gateway ECU*4
  9. Combination meter assembly
  10. 4WD control ECU*5
  11. Clearance warning ECU assembly*5, *6
  12. Master cylinder solenoid (skid control ECU)*5
  13. No. 1 junction connector
  14. No. 2 junction connector
  15. No. 3 junction connector
  16. No. 6 junction connector*5
  1. *1: w/ Airbag System
  2. *2: w/ Dynamic Headlight Auto Leveling
  3. *3: w/ Navigation System
  4. *4: w/ Network Gateway ECU
  5. *5: w/o Network Gateway ECU
  6. *6: w/ TOYOTA Parking Assist-sensor System and w/o Side Monitor System

WIRING DIAGRAM

C258823E01
C258824E01
C258825E01
C258826E01

INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


NEXT


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    For vehicles with an SRS system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


3. CHECK FOR SHORT TO GND IN CAN BUS WIRE (DLC3 CAN BRANCH WIRE)

  1. C253362E08
    Disconnect the E75 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E22-6 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E22-14 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


4. CONNECT CONNECTOR
  1. Reconnect the E75 No. 3 junction connector.


NEXT


5. SYSTEM CHECK
  1. Check the vehicle specifications.

    Result 
    Result
    Proceed to
    w/ Network Gateway ECU
    A
    w/o Network Gateway ECU
    B



B
Go to step 28
A


6. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR SIDE)

  1. C253362E08
    Disconnect the E72 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E22-6 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E22-14 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 13
OK


7. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - HEADLIGHT SWIVEL ECU ASSEMBLY)

NOTICE:
For vehicles without dynamic headlight auto leveling, go to "Check for Short to GND in CAN Bus Wire (No. 1 Junction Connector - Center Airbag Sensor Assembly)".

  1. C259545E15
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-3 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E72-14 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 10
OK


8. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)

  1. C259545E16
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-4 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E72-15 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 11
OK


9. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - ECM)

  1. C259545E17
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-2 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E72-13 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 12
OK

REPLACE NO. 1 JUNCTION CONNECTOR

10. CHECK FOR SHORT TO GND IN CAN BUS WIRE (HEADLIGHT SWIVEL ECU ASSEMBLY)

  1. C259545E15
    Disconnect the E101 headlight swivel ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-3 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E72-14 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO HEADLIGHT SWIVEL ECU ASSEMBLY (MPX1, MPX2)
OK

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY (Click here)

11. CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY)

  1. C259545E16
    Disconnect the E47 center airbag sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-4 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E72-15 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CANH, CANL)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

12. CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM)

  1. C259545E17
    Disconnect the A38 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-2 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E72-13 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3
    Result 
    Result
    Proceed to
    OK (for 1GR-FE)
    A
    OK (for 1UZ-FE)
    B
    OK (for 3UR-FE)
    C
    OK (for 1VD-FTV)
    D
    NG
    E



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)

E
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
A

REPLACE ECM (Click here)

13. CONNECT CONNECTOR
  1. Reconnect the E72 No. 1 junction connector.


NEXT


14. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

  1. C259545E18
    Disconnect the E69 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-1 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E69-12 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
OK


15. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR SIDE)

  1. C253362E08
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E22-6 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E22-14 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 22
OK


16. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - MULTI-MEDIA MODULE RECEIVER ASSEMBLY)

NOTICE:
For vehicles without a navigation system, go to "Check for Short to GND in CAN Bus Wire (No. 2 Junction Connector - Air Conditioning Amplifier Assembly)".

  1. C259545E19
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-2 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E69-13 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 19
OK


17. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

  1. C259545E20
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-5 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E69-16 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 20
OK


18. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

  1. C259545E21
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-3 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E69-14 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 21
OK

REPLACE NO. 2 JUNCTION CONNECTOR

19. CHECK FOR SHORT TO GND IN CAN BUS WIRE (MULTI-MEDIA MODULE RECEIVER ASSEMBLY)

  1. C259545E19
    Disconnect the F77 multi-media module receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-2 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E69-13 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MULTI-MEDIA MODULE RECEIVER ASSEMBLY (CANH, CANL)
OK

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY (Click here)

20. CHECK FOR SHORT TO GND IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)

  1. C259545E20
    Disconnect the E35*1 or E81*2 air conditioning amplifier assembly connector.
    1. *1: w/ Rear Air Conditioning System
    2. *2: w/o Rear Air Conditioning System

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-5 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E69-16 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (CANH, CANL)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

21. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NETWORK GATEWAY ECU)

  1. C259545E21
    Disconnect the E31 network gateway ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-3 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E69-14 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NETWORK GATEWAY ECU (CA1H, CA1L)
OK

REPLACE NETWORK GATEWAY ECU (Click here)

22. CONNECT CONNECTOR
  1. Reconnect the E69 No. 2 junction connector.


NEXT


23. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

  1. C259545E22
    Disconnect the E75 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-1 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E75-12 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK


24. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)

  1. C259545E23
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-4 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E75-15 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 26
OK


25. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

  1. C259545E24
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-3 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E75-14 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 27
OK

REPLACE NO. 3 JUNCTION CONNECTOR

26. CHECK FOR SHORT TO GND IN CAN BUS WIRE (MAIN BODY ECU)

  1. C259545E23
    Disconnect the E3 main body ECU (cowl side junction block LH) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-4 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E75-15 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

27. CHECK FOR SHORT TO GND IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)

  1. C259545E24
    Disconnect the E7 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-3 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E75-14 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3
    Result 
    Result
    Proceed to
    OK (w/ Multi-information Display)
    A
    OK (w/o Multi-information Display)
    B
    NG
    C



B
REPLACE COMBINATION METER ASSEMBLY (Click here)

C
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)
A

REPLACE COMBINATION METER ASSEMBLY (Click here)

28. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR SIDE)

  1. C253362E08
    Disconnect the E72 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E22-6 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E22-14 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 35
OK


29. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)

NOTICE:
For vehicles without an airbag system, go to "Check for Short to GND in CAN Bus Wire (No. 1 Junction Connector - 4WD Control ECU)".

  1. C259545E16
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-4 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E72-15 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 32
OK


30. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - 4WD CONTROL ECU)

  1. C259545E25
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-5 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E72-16 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 33
OK


31. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - ECM)

  1. C259545E17
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-2 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E72-13 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 34
OK

REPLACE NO. 1 JUNCTION CONNECTOR

32. CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY)

  1. C259545E16
    Disconnect the E47 center airbag sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-4 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E72-15 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CANH, CANL)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

33. CHECK FOR SHORT TO GND IN CAN BUS WIRE (4WD CONTROL ECU)

  1. C259545E25
    Disconnect the A27 4WD control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-5 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E72-16 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO 4WD CONTROL ECU (CAN+, CAN-)
OK

REPLACE 4WD CONTROL ECU (Click here)

34. CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM)

  1. C259545E17
    Disconnect the A38 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-2 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E72-13 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3
    Result 
    Result
    Proceed to
    OK (for 1GR-FE)
    A
    OK (for 1UZ-FE)
    B
    OK (for 1VD-FTV)
    C
    NG
    D



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
A

REPLACE ECM (Click here)

35. CONNECT CONNECTOR
  1. Reconnect the E72 No. 1 junction connector.


NEXT


36. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

  1. C259545E18
    Disconnect the E69 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-1 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E69-12 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
OK


37. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR SIDE)

  1. C253362E08
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E22-6 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E22-14 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 42
OK


38. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - MULTI-MEDIA MODULE RECEIVER ASSEMBLY)

NOTICE:
For vehicles without a navigation system, go to "Check for Short to GND in CAN Bus Wire (No. 2 Junction Connector - Air Conditioning Amplifier)".

  1. C259545E19
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-2 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E69-13 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 40
OK


39. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

  1. C259545E20
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-5 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E69-16 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 41
OK

REPLACE NO. 2 JUNCTION CONNECTOR

40. CHECK FOR SHORT TO GND IN CAN BUS WIRE (MULTI-MEDIA MODULE RECEIVER ASSEMBLY)

  1. C259545E19
    Disconnect the F77 multi-media module receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-2 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E69-13 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MULTI-MEDIA MODULE RECEIVER ASSEMBLY (CANH, CANL)
OK

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY (Click here)

41. CHECK FOR SHORT TO GND IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)

  1. C259545E20
    Disconnect the E35*1 or E81*2 air conditioning amplifier connector.
    1. *1: w/ Rear Air Conditioning System
    2. *2: w/o Rear Air Conditioning System

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-5 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E69-16 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (CANH, CANL)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

42. CONNECT CONNECTOR
  1. Reconnect the E69 No. 2 junction connector.


NEXT


43. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 6 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

  1. C259545E26
    Disconnect the F73 No. 6 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F73-7 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    F73-18 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 6 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK


44. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 6 JUNCTION CONNECTOR SIDE)

  1. C253362E08
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E22-6 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E22-14 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of DLC3
    Result 
    Result
    Proceed to
    OK (w/ TOYOTA parking assist-sensor system)
    A
    OK (w/o TOYOTA parking assist-sensor system)
    B
    NG
    C



B
REPLACE NO. 6 JUNCTION CONNECTOR

C
Go to step 47
A


45. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 6 JUNCTION CONNECTOR - CLEARANCE WARNING ECU ASSEMBLY)

  1. C259545E27
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F73-5 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    F73-16 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 6 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 46
OK

REPLACE NO. 6 JUNCTION CONNECTOR

46. CHECK FOR SHORT TO GND IN CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY)

  1. C259545E27
    Disconnect the F12 clearance warning ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F73-5 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    F73-16 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 6 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CLEARANCE WARNING ECU ASSEMBLY (CANH, CANL)
OK

REPLACE CLEARANCE WARNING ECU ASSEMBLY (Click here)

47. CONNECT CONNECTOR
  1. Reconnect the F73 No. 6 junction connector.


NEXT


48. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)

  1. C259545E22
    Disconnect the E75 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-1 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E75-12 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)
OK


49. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)

  1. C259545E23
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-4 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E75-15 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 52
OK


50. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - SKID CONTROL ECU)

  1. C259545E28
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-5 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E75-16 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 53
OK


51. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

  1. C259545E24
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-3 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E75-14 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 54
OK

REPLACE NO. 3 JUNCTION CONNECTOR

52. CHECK FOR SHORT TO GND IN CAN BUS WIRE (MAIN BODY ECU)

  1. C259545E23
    Disconnect the E3 main body ECU (cowl side junction block LH) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-4 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E75-15 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

53. CHECK FOR SHORT TO GND IN CAN BUS WIRE (SKID CONTROL ECU)

  1. C259545E28
    Disconnect the A24 master cylinder solenoid (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-5 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E75-16 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)
OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU) (Click here)

54. CHECK FOR SHORT TO GND IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)

  1. C259545E24
    Disconnect the E7 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-3 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E75-14 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3
    Result 
    Result
    Proceed to
    OK (w/ Multi-information Display)
    A
    OK (w/o Multi-information Display)
    B
    NG
    C



B
REPLACE COMBINATION METER ASSEMBLY (Click here)

C
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)
A

REPLACE COMBINATION METER ASSEMBLY (Click here)


← Short to GND in CAN Bus Line (Sep 2011 – Dec 2011)Open in One Side of CAN Branch Line (Sep 2011 – Dec 2011) →