2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

B15C3 Speaker Output Short

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.
DTC No.
DTC Detection Condition
Trouble Area
B15C3
A short is detected in the speaker output circuit.
  1. Wire harness or connector
  2. Speaker
  3. Stereo component amplifier assembly

WIRING DIAGRAM

E155742E05
E192482E02
E192483E02

INSPECTION PROCEDURE


1. SYSTEM CHECK
  1. Check the vehicle specifications.

    Result 
    Result
    Proceed to
    for 9 speakers model
    A
    for 14 speakers model
    B



B
Go to step 12
A


2. CHECK DTC
  1. Disconnect the F3 and F52 stereo component amplifier assembly connectors.

  1. Clear the DTCs.

  1. Check if DTC B15C3 is output.

    OK:
    DTC B15C3 is not output.



NG
REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)
OK


3. CHECK DTC
  1. Reconnect the F52 stereo component amplifier assembly connector.

  1. Clear the DTCs.

  1. Check if DTC B15C3 is output.

    OK:
    DTC B15C3 is not output.



NG
Go to step 7
OK


4. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - SPEAKERS)
  1. Disconnect the F3 stereo component amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F3-8 (CTR+) - Body ground
    Always
    10 kΩ or higher
    F3-7 (CTR-) - Body ground
    Always
    10 kΩ or higher
    F3-1 (WFL+) - Body ground
    Always
    10 kΩ or higher
    F3-5 (WFL-) - Body ground
    Always
    10 kΩ or higher
    F3-2 (WFR+) - Body ground
    Always
    10 kΩ or higher
    F3-6 (WFR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

  1. E192484E01
    Disconnect the I1 and I10 front No. 1 speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    3 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Front No. 1 Speaker Assembly)



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


6. INSPECT FRONT NO. 4 SPEAKER ASSEMBLY

  1. E192485E01
    Disconnect the F6 front No. 4 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    6 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Front No. 4 Speaker Assembly)



NG
REPLACE FRONT NO. 4 SPEAKER ASSEMBLY (Click here)
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)

7. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - SPEAKERS)
  1. Disconnect the F52 stereo component amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F52-3 (FL+) - Body ground
    Always
    10 kΩ or higher
    F52-8 (FL-) - Body ground
    Always
    10 kΩ or higher
    F52-10 (FR+) - Body ground
    Always
    10 kΩ or higher
    F52-9 (FR-) - Body ground
    Always
    10 kΩ or higher
    F52-5 (RR+) - Body ground
    Always
    10 kΩ or higher
    F52-12 (RR-) - Body ground
    Always
    10 kΩ or higher
    F52-4 (RL+) - Body ground
    Always
    10 kΩ or higher
    F52-11 (RL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. INSPECT REAR SPEAKER SET

  1. E192486E01
    Disconnect the J17 and J15 rear speaker set connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    4 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Rear Speaker Set)



NG
REPLACE REAR SPEAKER SET (Click here)
OK


9. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

  1. E192487E01
    Disconnect the F8 and F7 front No. 2 speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    Below 1 Ω
    3 - 4
    Always
    Below 1 Ω
    2 - 4
    Always
    4 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Front No. 2 Speaker Assembly)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


10. INSPECT FRONT NO. 3 SPEAKER ASSEMBLY

  1. E192488E01
    Disconnect the F14 and F13 front No. 3 speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    4 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Front No. 3 Speaker Assembly)



NG
REPLACE FRONT NO. 3 SPEAKER ASSEMBLY (Click here)
OK


11. CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER - FRONT NO. 3 SPEAKER)
  1. Disconnect the F7 and F8 front No. 2 speaker assembly connectors.

  1. Disconnect the F13 and F14 front No. 3 speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side:
    Tester Connection
    Condition
    Specified Condition
    F8-2 (TWL+) - F14-1
    Always
    Below 1 Ω
    F8-4 (TWL-) - F14-2
    Always
    Below 1 Ω
    F8-2 (TWL+) - Body ground
    Always
    10 kΩ or higher
    F8-4 (TWL-) - Body ground
    Always
    10 kΩ or higher
    for RH Side:
    Tester Connection
    Condition
    Specified Condition
    F7-2 (TWR+) - F13-2
    Always
    Below 1 Ω
    F7-4 (TWR-) - F13-1
    Always
    Below 1 Ω
    F7-2 (TWR+) - Body ground
    Always
    10 kΩ or higher
    F7-4 (TWR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)

12. CHECK DTC
  1. Disconnect the F3 and F52 stereo component amplifier assembly connectors.

  1. Clear the DTCs.

  1. Check if DTC B15C3 is output.

    OK:
    DTC B15C3 is not output.



NG
REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)
OK


13. CHECK DTC
  1. Reconnect the F52 stereo component amplifier assembly connector.

  1. Clear the DTCs.

  1. Check if DTC B15C3 is output.

    OK:
    DTC B15C3 is not output.



NG
Go to step 19
OK


14. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - SPEAKERS)
  1. Disconnect the F3 stereo component amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F3-3 (CTR+) - Body ground
    Always
    10 kΩ or higher
    F3-9 (CTR-) - Body ground
    Always
    10 kΩ or higher
    F3-1 (WFL+) - Body ground
    Always
    10 kΩ or higher
    F3-5 (WFL-) - Body ground
    Always
    10 kΩ or higher
    F3-2 (WFR+) - Body ground
    Always
    10 kΩ or higher
    F3-6 (WFR-) - Body ground
    Always
    10 kΩ or higher
    F3-8 (SL+) - Body ground
    Always
    10 kΩ or higher
    F3-7 (SL-) - Body ground
    Always
    10 kΩ or higher
    F3-4 (WF2+) - Body ground
    Always
    10 kΩ or higher
    F3-10 (WF2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


15. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

  1. E192484E01
    Disconnect the I1 and I10 front No. 1 speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.8 to 2.6 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Front No. 1 Speaker Assembly)



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


16. INSPECT FRONT NO. 4 SPEAKER ASSEMBLY

  1. E192485E01
    Disconnect the F6 front No. 4 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.5 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Front No. 4 Speaker Assembly)



NG
REPLACE FRONT NO. 4 SPEAKER ASSEMBLY (Click here)
OK


17. INSPECT REAR HEADER SPEAKER LH

  1. E192485E01
    Disconnect the S9 rear header speaker LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.5 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Rear Header Speaker LH)



NG
REPLACE REAR HEADER SPEAKER LH
OK


18. INSPECT NO. 1 WOOFER BOX SPEAKER

  1. E192489E01
    Disconnect the L4 No. 1 woofer box speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 4
    Always
    1.6 to 2.4 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (No. 1 woofer box speaker)



NG
REPLACE NO. 1 WOOFER BOX SPEAKER
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)

19. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - SPEAKERS)
  1. Disconnect the F52 stereo component amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F52-3 (FL+) - Body ground
    Always
    10 kΩ or higher
    F52-8 (FL-) - Body ground
    Always
    10 kΩ or higher
    F52-10 (FR+) - Body ground
    Always
    10 kΩ or higher
    F52-9 (FR-) - Body ground
    Always
    10 kΩ or higher
    F52-4 (R-L+) - Body ground
    Always
    10 kΩ or higher
    F52-11 (R-L-) - Body ground
    Always
    10 kΩ or higher
    F52-5 (R-R+) - Body ground
    Always
    10 kΩ or higher
    F52-12 (R-R-) - Body ground
    Always
    10 kΩ or higher
    F52-2 (SR+) - Body ground
    Always
    10 kΩ or higher
    F52-7 (SR-) - Body ground
    Always
    10 kΩ or higher
    F52-1 (WF1+) - Body ground
    Always
    10 kΩ or higher
    F52-6 (WF1-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


20. INSPECT REAR HEADER SPEAKER RH

  1. E192485E01
    Disconnect the S8 rear header speaker RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.5 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Rear Header Speaker RH)



NG
REPLACE REAR HEADER SPEAKER RH
OK


21. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

  1. E192487E01
    Disconnect the F8 and F7 front No. 2 speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    Below 1 Ω
    3 - 4
    Always
    Below 1 Ω
    2 - 4
    Always
    1.5 to 2.5 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Front No. 2 Speaker Assembly)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


22. INSPECT FRONT NO. 3 SPEAKER ASSEMBLY

  1. E192488E01
    Disconnect the F14 and F13 front No. 3 speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    4 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Front No. 3 Speaker Assembly)



NG
REPLACE FRONT NO. 3 SPEAKER ASSEMBLY (Click here)
OK


23. CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER - FRONT NO. 3 SPEAKER)
  1. Disconnect the F7 and F8 front No. 2 speaker assembly connectors.

  1. Disconnect the F13 and F14 front No. 3 speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side:
    Tester Connection
    Condition
    Specified Condition
    F8-2 (TWL+) - F14-1
    Always
    Below 1 Ω
    F8-4 (TWL-) - F14-2
    Always
    Below 1 Ω
    F8-2 (TWL+) - Body ground
    Always
    10 kΩ or higher
    F8-4 (TWL-) - Body ground
    Always
    10 kΩ or higher
    for RH Side:
    Tester Connection
    Condition
    Specified Condition
    F7-2 (TWR+) - F13-2
    Always
    Below 1 Ω
    F7-4 (TWR-) - F13-1
    Always
    Below 1 Ω
    F7-2 (TWR+) - Body ground
    Always
    10 kΩ or higher
    F7-4 (TWR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


24. INSPECT REAR NO. 3 SPEAKER ASSEMBLY

  1. E192490E01
    Disconnect the J2 and J9 rear No. 3 speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    Below 1 Ω
    3 - 4
    Always
    Below 1 Ω
    2 - 4
    Always
    4 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Rear No. 3 Speaker Assembly)



NG
REPLACE REAR NO. 3 SPEAKER ASSEMBLY (Click here)
OK


25. INSPECT REAR SPEAKER SET

  1. E192484E01
    Disconnect the J18 and J19 rear speaker set connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.3 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Rear Speaker Set)



NG
REPLACE REAR SPEAKER SET (Click here)
OK


26. CHECK HARNESS AND CONNECTOR (REAR NO. 3 SPEAKER - REAR SPEAKER SET)
  1. Disconnect the J2 and J9 rear No. 3 speaker assembly connectors.

  1. Disconnect the J18 and J19 rear speaker set connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side:
    Tester Connection
    Condition
    Specified Condition
    J9-2 (+) - J19-1
    Always
    Below 1 Ω
    J9-4 (-) - J19-2
    Always
    Below 1 Ω
    J9-2 (+) - Body ground
    Always
    10 kΩ or higher
    J9-4 (-) - Body ground
    Always
    10 kΩ or higher
    for RH Side:
    Tester Connection
    Condition
    Specified Condition
    J2-2 (+) - J18-1
    Always
    Below 1 Ω
    J2-4 (-) - J18-2
    Always
    Below 1 Ω
    J2-2 (+) - Body ground
    Always
    10 kΩ or higher
    J2-4 (-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


27. INSPECT NO. 1 WOOFER BOX SPEAKER

  1. E192489E01
    Disconnect the L4 No. 1 woofer box speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.6 to 2.4 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (No. 1 woofer box speaker)



NG
REPLACE NO. 1 WOOFER BOX SPEAKER
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)


← B15C2 Speed Signal Malfunction (from Jan 2012)B15C3 Speaker Output Short (from Jan 2012) →