2011-2013 Land Cruiser · Service Manual Vehicle Exterior

INSTALLATION

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).


1. INSTALL FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY

  1. Connect the cable to the clamps shown in the illustration to install the cable.

    B181052


2. INSTALL FUEL FILLER OPENING LID LOCK RETAINER

B181055
  1. Install the lock retainer and turn it clockwise as shown in the illustration.

  1. B181056
    Install the cable and turn it clockwise as shown in the illustration.


3. INSTALL FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY

  1. B181065
    Connect the fuel lid lock control cable to the fuel lid lock open lever.

  1. Attach the 2 claws to install the fuel lid lock open lever.


4. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH

B182645

HINT:
When installing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.

  1. w/ Rear No. 2 Seat, except Face to Face Seat Type:

    1. w/o Rear Air Conditioning System:
      Connect the rear seat lock control lever cable.

    2. w/ Rear Air Conditioning System:
      Connect the thermistor connector and rear seat lock control lever cable.

    3. Attach the 16 clips and 2 claws to install the quarter trim panel.

    4. Install the clip and bolt.

      Torque:
      12 N*m{ 122 kgf*cm , 9 ft.*lbf }


      B186890

  1. w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:

    1. Attach the 16 clips and 2 claws to install the quarter trim panel.

    2. Install the clip.

      B190220

  1. w/ Tonneau Cover:

    1. Attach the 16 clips and 2 claws to install the quarter trim panel.

    2. Install the screw and clip.

      B186438

  1. B181693
    w/ Rear No. 2 Seat, except Face to Face Seat Type:

    1. Install the rear No. 2 seat belt anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    2. B181692
      Attach the 3 claws to install the cover.

  1. B181690
    Install the rear No. 1 seat belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B181688
    Attach the 3 claws to install the cover.


5. INSTALL REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type)

B190214

HINT:
Use the same procedure to install the rear seat cover cap on the other side.

  1. Attach the 3 claws to install the rear seat cover cap.


6. INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/ Tonneau Cover)

B186439

HINT:
Use the same procedure to install the tonneau cover holder cap on the other side.

  1. Attach the 2 claws to install the tonneau cover holder cap.


7. INSTALL FRONT FLOOR CARPET ASSEMBLY

  1. B186248
    Open the tail gate and back door, insert the carpet into the cabin from the rear, and install it to the floor.

  1. Attach the 2 clips and 8 claws.

    B183331


8. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE

B181672
  1. Attach the 6 clips to install the support plate.


9. INSTALL REAR CONSOLE BOX SUB-ASSEMBLY
  1. w/o Console Box Lid:
    (Click here)

  1. w/ Cool Box:
    (Click here)

  1. w/o Cool Box:
    (Click here)


10. INSTALL REAR NO. 2 SEAT PROTECTOR

  1. B184595
    Attach the clip and 4 claws to install the protector.

    HINT:
    Use the same procedures to install the protector on the other side.


11. INSTALL REAR NO. 1 SEAT PROTECTOR

  1. B186247
    Attach the clip and 4 claws to install the protector.

    HINT:
    Use the same procedures to install the protector on the other side.


12. INSTALL AIR DUCT GUIDE

  1. B183334
    Attach the claw to install the guide.

  1. Install the screw.

    HINT:
    Use the same procedures for both sides.


13. INSTALL AIR DUCT PLUG

  1. B183333
    Attach the 2 claws to install the plug.

    HINT:
    Use the same procedures for both sides.


14. INSTALL AIR HEATER GUIDE

  1. B183336
    Install the guide with the 2 screws.

    HINT:
    Use the same procedures for both sides.


15. INSTALL NO. 2 AIR DUCT PLUG

  1. B183335
    Attach the 4 claws to install the 2 plugs.

    HINT:
    Use the same procedures for both sides.


16. INSTALL REAR DOOR SCUFF PLATE LH

B181674
  1. Attach the 3 claws and 4 clips to install the scuff plate.

  1. Install the screw.


17. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.


18. INSTALL REAR STEP COVER

B181673

HINT:
Use the same procedure to install the step cover on the other side.

  1. Attach the 2 claws to install the step cover.


19. INSTALL COWL SIDE TRIM BOARD LH

B181911
  1. Attach the 2 clips to install the cowl side trim board.

  1. Install the cap nut.


20. INSTALL COWL SIDE TRIM BOARD RH

B180022
  1. Attach the 2 clips to install the cowl side trim board.

  1. Install the cap nut.


21. INSTALL FRONT DOOR SCUFF PLATE LH

B181682
  1. Attach the 7 claws and 4 clips to install the scuff plate.


22. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.


23. INSTALL INSTRUMENT SIDE PANEL LH

E155518
  1. Attach the 6 claws to install the instrument side panel.


24. INSTALL INSTRUMENT SIDE PANEL RH (w/ Airbag Cut Off Switch)

B186358
  1. Connect the connector.

  1. Attach the 6 claws to install the instrument side panel.


25. INSTALL INSTRUMENT SIDE PANEL RH (w/o Airbag Cut Off Switch)

B182551
  1. Attach the 6 claws to install the instrument side panel.


26. INSTALL REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Seat Type 40 Side)
(Click here)

27. INSTALL REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Seat Type 60 Side)
(Click here)

28. INSTALL REAR NO. 1 SEAT ASSEMBLY (for Bench Seat Type)
(Click here)

29. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Install the tonneau cover assembly.


30. INSTALL FRONT SEAT ASSEMBLY RH
  1. for Manual Seat:
    (Click here)

  1. for Power Seat:
    (Click here)

  1. for Bench Seat Type:
    (Click here)


31. INSTALL FRONT SEAT ASSEMBLY LH
  1. for Manual Seat:
    (Click here)

  1. for Power Seat:
    (Click here)


32. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


33. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).

← INSTALLATION (Sep 2011 – Dec 2011)COMPONENTS (from Sep 2011) →