2011-2013 Land Cruiser · Service Manual Power Source / Network

Short in CAN Bus Lines

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
  1. Short between CAN bus lines
  2. ECM
  3. Center airbag sensor assembly*1
  4. Display and navigation module display*2
  5. Air conditioning amplifier assembly
  6. Network gateway ECU
  7. Main body ECU (cowl side junction block LH)
  8. Combination meter assembly
  9. No. 1 junction connector
  10. No. 2 junction connector
  11. No. 3 junction connector

HINT:
*1: w/ Airbag System
*2: w/ Navigation System


WIRING DIAGRAM

C176035E03
C176036E06

INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    For vehicles with an SRS system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK FOR SHORT IN CAN BUS WIRES (DLC3 BRANCH WIRE)

  1. E194588E04
    Disconnect the E75 No. 3 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E22-6 (CANH) - E22-14 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *1
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


3. CONNECT CONNECTOR
  1. Reconnect the E75 No. 3 junction connector connector.


NEXT


4. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR SIDE)

  1. E194588E04
    Disconnect the E72 No. 1 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E22-6 (CANH) - E22-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    DLC3



NG
Go to step 11
OK


5. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR)

NOTICE:
For vehicles without the airbag system, go to "Check for Short in CAN Bus Wires (No. 1 Junction Connector - Main Body ECU)".

  1. E186808E31
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-4 (CANH) - E72-15 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 8
OK


6. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - MAIN BODY ECU)

  1. E186808E32
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-3 (CANH) - E72-14 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 9
OK


7. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - ECM)

  1. E186808E33
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-2 (CANH) - E72-13 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 10
OK

REPAIR OR REPLACE NO. 1 JUNCTION CONNECTOR

8. CHECK FOR SHORT IN CAN BUS WIRES (CENTER AIRBAG SENSOR)

  1. E186808E31
    Disconnect the E47 center airbag sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-4 (CANH) - E72-15 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR (CANH, CANL)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

9. CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)

  1. E186808E32
    Disconnect the E3 main body ECU (cowl side junction block LH) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-3 (CANH) - E72-14 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH) (CANH, CANL)
OK

REPLACE MAIN BODY ECU

10. CHECK FOR SHORT IN CAN BUS WIRES (ECM)

  1. E186808E33
    Disconnect the A52 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-2 (CANH) - E72-13 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    Result 
    Result
    Proceed to
    OK (for 2UZ-FE)
    A
    OK (for 1GR-FE)
    B
    OK (for 1KD-FTV)
    C
    NG
    D



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
A

REPLACE ECM (Click here)

11. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

  1. E186808E41
    Disconnect the E69 No. 2 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-4 (CANH) - E69-15 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK


12. CONNECT CONNECTOR
  1. Reconnect the E72 No. 1 junction connector connector.


NEXT


13. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR SIDE)
E194588E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E22-6 (CANH) - E22-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    DLC3



NG
Go to step 20
OK


14. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - DISPLAY AND NAVIGATION MODULE DISPLAY)

NOTICE:
For vehicles without the navigation system, go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - Air Conditioning Amplifier)".

  1. E186808E35
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-2 (CANH) - E69-13 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 17
OK


15. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER)

  1. E186808E36
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-5 (CANH) - E69-16 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 18
OK


16. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

  1. E186808E37
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-3 (CANH) - E69-14 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 19
OK

REPAIR OR REPLACE NO. 2 JUNCTION CONNECTOR

17. CHECK FOR SHORT IN CAN BUS WIRES (DISPLAY AND NAVIGATION MODULE DISPLAY)

  1. E186808E35
    Disconnect the F64 display and navigation module display connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-2 (CANH) - E69-13 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DISPLAY AND NAVIGATION MODULE DISPLAY (CANH, CANL)
OK

REPLACE DISPLAY AND NAVIGATION MODULE DISPLAY (Click here)

18. CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER)

  1. E186808E36
    Disconnect the E35*1 or E81*2 air conditioning amplifier connector.

    HINT:
    *1: w/ Rear Air Conditioning System
    *2: w/o Rear Air Conditioning System

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-5 (CANH) - E69-16 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER (CANH, CANL)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

19. CHECK FOR SHORT IN CAN BUS WIRES (NETWORK GATEWAY ECU)

  1. E186808E37
    Disconnect the E31 network gateway ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-3 (CANH) - E69-14 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NETWORK GATEWAY ECU (CANH, CANL)
OK

REPLACE NETWORK GATEWAY ECU (Click here)

20. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

  1. E186808E38
    Disconnect the E75 No. 3 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-1 (CANH) - E75-12 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
OK


21. CONNECT CONNECTOR
  1. Reconnect the E69 No. 2 junction connector connector.


NEXT


22. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - COMBINATION METER)

  1. E186808E40
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-3 (CANH) - E75-14 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
Go to step 23
OK

REPAIR OR REPLACE NO. 3 JUNCTION CONNECTOR

23. CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER)

  1. E186808E40
    Disconnect the E7 combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-3 (CANH) - E75-14 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    Result 
    Result
    Proceed to
    OK (w/ Multi-information Display)
    A
    OK (w/o Multi-information Display)
    B
    NG
    C



B
REPLACE COMBINATION METER ASSEMBLY (Click here)

C
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER (CANH, CANL)
A

REPLACE COMBINATION METER ASSEMBLY (Click here)


← Open in CAN Main Wire (from Jan 2012)Short in CAN Bus Lines (from Jan 2012) →