2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built from Jan 2012


1. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)

2. PRECAUTION

NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


4. REMOVE V-BANK COVER SUB-ASSEMBLY

  1. A274415E01
    Raise the front of the V-bank cover to detach the 3 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.
    Text in Illustration 
    *1
    Grommet
    *2
    Pin
    *3
    Hook
    *4
    Bracket


5. REMOVE AIR CLEANER AND HOSE

  1. A271401
    Disconnect the No. 2 PCV hose and No. 1 air hose.

  1. Disconnect the mass air flow meter connector and detach the clamp.

  1. Remove the 3 bolts and loosen the hose clamp, and then remove the air cleaner and hose.


6. REMOVE FRONT FENDER APRON TRIM PACKING A

  1. A177003
    Remove the 3 clips and front fender apron trim packing A.


7. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. A174194
    Remove the 2 bolts and No. 2 engine under cover seal.

  1. Remove the oil pan drain plug and gasket, and drain the engine oil into a container.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. Install the No. 2 engine under cover seal with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


8. REMOVE RADIATOR ASSEMBLY
(Click here)

9. REMOVE INTAKE MANIFOLD
(Click here)

10. DISCONNECT COOLER COMPRESSOR ASSEMBLY

  1. A178491
    Remove the 3 bolts, nut and stud bolt, and then disconnect the cooler compressor.

    HINT:
    It is not necessary to completely remove the compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.


11. REMOVE AIR SWITCHING VALVE ASSEMBLY (w/ Secondary Air Injection System)
  1. for Bank 1 (Click here)
  2. for Bank 2 (Click here)

12. REMOVE AIR TUBE (w/ Secondary Air Injection System)

  1. A272570
    Detach the wire harness clamp.

  1. Disconnect the No. 3 air injection system hose.

  1. Remove the 2 bolts and air tube.


13. DISCONNECT ENGINE WIRE

  1. for Engine Room LH Side:

    1. A272568
      Disconnect the injector connector.

    2. Disconnect the 2 camshaft timing oil control valve connectors.

    3. Disconnect the 4 ignition coil connectors.

    4. Disconnect the 2 VVT sensor connectors.

    5. Disconnect the camshaft position sensor connector.

    6. Disconnect the engine coolant temperature sensor connector.

    7. Disconnect the noise filter connector.

    8. Disconnect the 8 clamps.

    9. Remove the bolt and ground wire.

  1. for Engine Room RH Side:

    1. A272569
      Disconnect the 2 camshaft timing oil control valve connectors.

    2. Disconnect the 4 ignition coil connectors.

    3. Disconnect the 2 VVT sensor connectors.

    4. Disconnect the injector connector.

    5. Disconnect the noise filter connector.

    6. Disconnect the 6 clamps.

  1. A272571
    Remove the bolt and disconnect the clamp and engine wire.


14. REMOVE OIL FILTER ELEMENT

  1. A094910E10
    Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
    Text in Illustration 
    *1
    Pipe
    *2
    Hose

  1. A207196
    Remove the oil filter drain plug.

  1. A272715E01
    Install the pipe to the oil filter cap.
    Text in Illustration 
    *1
    Cap
    *2
    Valve
    *3
    Pipe
    *4
    O-Ring
    *5
    Hose

    NOTICE:
    If the O-ring is removed with the drain plug, install the O-ring together with the pipe.

    HINT:
    Use a container to catch the draining oil.

  1. A207198
    Check that oil is drained from the oil filter. Then disconnect the pipe and remove the O-ring as shown in the illustration.

  1. A207199E02
    Using SST, remove the oil filter cap.
    SST
    09228-06501  
    Text in Illustration 
    *1
    Oil Filter Bracket Clip

    NOTICE:
    Do not remove the oil filter bracket clip.

  1. A209947E02
    Remove the oil filter element and O-ring from the oil filter cap.
    Text in Illustration 
    *1
    Oil Filter Element
    *2
    O-Ring

    NOTICE:
    Be sure to remove the cap O-ring by hand, without using any tools, to prevent damage to the cap O-ring groove.


15. REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY

  1. A163657
    Disconnect the oil pressure sender gauge connector.

  1. A162467
    Remove the oil pressure sender gauge.


16. REMOVE NO. 1 OIL COOLER BRACKET

  1. A272590
    Remove the 2 nuts and bracket.

  1. Disconnect the ground wire from the cylinder block.


17. REMOVE OIL FILTER BRACKET

  1. A162469
    Remove the 2 bolts, 2 nuts and filter bracket.

  1. A162470
    Remove the 2 O-rings.


18. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A218612
    Remove the engine oil level dipstick.

  1. Detach the engine wire clamp.

  1. Remove the bolt and engine oil level dipstick guide.

  1. Remove the O-ring from the engine oil level dipstick guide.


19. DISCONNECT POWER STEERING OIL PRESSURE SWITCH CONNECTOR

20. DISCONNECT VANE PUMP ASSEMBLY
  1. Remove the 2 bolts and disconnect the vane pump.


21. DISCONNECT OIL COOLER TUBE

  1. A272652
    Remove the 2 bolts and disconnect the oil cooler tube.


22. REMOVE GENERATOR ASSEMBLY

  1. A177892
    Disconnect the generator connector.

  1. Open the terminal cap.

  1. Remove the nut and disconnect the generator wire.

  1. Remove the bolt and disconnect the wire harness bracket from the generator.

  1. A177893
    Remove the 3 bolts, nut and generator.

  1. Remove the stud bolt.


23. REMOVE NO. 4 ENGINE COVER

A214270

24. REMOVE NO. 3 ENGINE COVER

A214271

25. REMOVE FUEL TUBE SUB-ASSEMBLY

  1. A272572
    Remove the 2 bolts and fuel tube (Click here).


26. REMOVE FUEL HOSE
  1. Remove the fuel pipe clamp.

  1. A272573
    Disconnect the 2 clamps and remove the fuel hose (Click here).


27. REMOVE NO. 4 AIR TUBE (w/ Secondary Air Injection System)

  1. A272588E01
    Remove the bolt and bracket.
    Text in Illustration 
    *A
    for RHD
    *B
    for LHD

  1. A272653
    Remove the bolt, 2 nuts, 2 stud bolts, No. 4 air tube and gasket.


28. REMOVE NO. 3 AIR TUBE (w/ Secondary Air Injection System)

  1. A272654
    Remove the bolt, 2 nuts, 2 stud bolts, No. 3 air tube and gasket.


29. REMOVE NO. 1 WATER BY-PASS PIPE

  1. A272576
    Disconnect the heater water hose.

  1. Remove the 2 bolts and disconnect the No. 1 water by-pass pipe.


30. DISCONNECT WATER BY-PASS HOSE

  1. A218799
    Disconnect the water by-pass hose.


31. REMOVE NO. 1 WATER BY-PASS HOSE

  1. A215865
    Remove the No. 1 water by-pass hose.


32. REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

  1. A210013
    Remove the 2 bolts.

  1. Disconnect the 4 hoses and remove the No. 2 water by-pass pipe.


33. DISCONNECT NO. 5 WATER BY-PASS HOSE

  1. A215869
    Disconnect the No. 5 water by-pass hose.


34. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

  1. A272575
    Disconnect the No. 2 water by-pass hose from the front water by-pass joint.

  1. Disconnect the heater hose.

  1. Remove the 2 bolts and water by-pass pipe sub-assembly.


35. REMOVE WATER INLET HOUSING

  1. A215871
    Remove the 3 bolts and water inlet housing.

  1. Remove the gasket from the engine water pump.


36. REMOVE FRONT WATER BY-PASS JOINT

  1. A229715
    Remove the 4 nuts, water by-pass joint and 2 gaskets.


37. REMOVE WATER PUMP PULLEY

  1. A230493E01
    Using SST, hold the water pump pulley.
    SST
    09960-10010   (09962-01000, 09963-01000)

  1. Remove the 4 bolts and water pump pulley.


38. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

  1. A210019
    Remove the bolt and No. 1 idler pulley.


39. REMOVE FAN BRACKET ASSEMBLY

  1. A210020
    Remove the 5 bolts and fan bracket.


40. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. A162527
    Remove the bolt, 6 mm hexagon bolt and belt tensioner.


41. REMOVE IGNITION COIL ASSEMBLY

  1. for Bank 1:

    1. A271367
      Detach the 4 clamps and disconnect the engine wire.

    2. Disconnect the 4 ignition coil connectors.

    3. A271372
      Remove the 4 bolts and 4 ignition coils.

  1. for Bank 2:

    1. A271376
      Remove the 2 bolts and disconnect the water by-pass pipe.

    2. A271366
      Detach the 3 clamps and disconnect the engine wire.

    3. Disconnect the 4 ignition coil connectors.

    4. A271373
      Remove the 4 bolts and 4 ignition coils.


42. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

  1. A210022
    Remove the 14 bolts, seal washer, cylinder head cover sub-assembly LH and cylinder head cover gasket LH.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.

  1. A229745
    Remove the 5 gaskets from the camshaft bearing caps (No. 2, No. 3).
    Text in Illustration 
    V100143
    Gasket


43. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH

  1. A210024
    Remove the 14 bolts, seal washer, cylinder head cover sub-assembly RH and cylinder head cover gasket RH.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.

  1. A229746
    Remove the 5 gaskets from the camshaft bearing caps (No. 1, No. 3).
    Text in Illustration 
    V100143
    Gasket


44. REMOVE CRANKSHAFT PULLEY

  1. A164228E03
    Using SST, remove the crankshaft pulley set bolt.
    SST
    09213-70011  
    09330-00021  
    Text in Illustration 
    *a
    Hold
    V100135
    Turn

  1. Temporarily install the pulley set bolt to the crankshaft until 2 or 3 threads are engaged.

  1. A164229E02
    Using the pulley set bolt and SST, remove the crankshaft pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05011)
    Text in Illustration 
    *a
    Hold
    V100135
    Turn


45. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

  1. A210026
    Remove the 26 bolts and nut shown in the illustration.

  1. A229747
    Remove the timing chain cover by prying between it and the cylinder head and cylinder block with a screwdriver as shown in the illustration.
    Text in Illustration 
    V100144
    Protective Tape

    NOTICE:
    Be careful not to damage the cylinder head, camshaft housing and cylinder block contact surfaces of the chain cover.

    HINT:
    Tape the screwdriver tip before use.

  1. A210028
    Remove the gasket from the cylinder block.

  1. A164415
    Remove the O-ring from the oil pan.


46. REMOVE WATER INLET PIPE

  1. A210029
    Remove the water inlet pipe.

  1. Remove the 2 O-rings from the water inlet pipe.


47. REMOVE FRONT CRANKSHAFT OIL SEAL

  1. A218840E01
    Using a screwdriver, pry out the front crankshaft oil seal.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Do not damage the surface of the front crankshaft oil seal press fit hole or crankshaft.

    HINT:
    Tape the screwdriver tip before use.

← COMPONENTS (from Jan 2012)DISASSEMBLY (from Jan 2012) →