B2325 LIN Communication Bus Malfunction
Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
The main body ECU (cowl side junction block LH) intermittently monitors the LIN communication bus between the components related to the door, double lock control relay*2 and sliding roof*1. DTC B2325 is stored when a malfunction in the LIN communication bus between the components related to the doors, double lock control relay*2 and sliding roof*1 is detected consecutively 3 times.- HINT:
- *1: w/ Sliding Roof System
- *2: w/ Double Locking System
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2325 |
The main body ECU (cowl side junction block LH) detects a malfunction in the LIN communication bus between components related to the doors and sliding roof consecutively 3 times. |
|
WIRING DIAGRAM




INSPECTION PROCEDURE
- NOTICE:
- When using the intelligent tester with the ignition switch off to troubleshoot:
- Connect the intelligent tester to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.
- HINT:
- When DTC B2325 and a LIN communication stop DTC are output simultaneously, first perform the troubleshooting for the LIN communication stop DTC. Then perform the troubleshooting for DTC B2325.
| 1. CLEAR DTC |
Clear the DTC (Click here).
| NEXT | |
| 2. CHECK FOR DTC |
Recheck for DTCs (Click here).
Result Result
Proceed to
DTC B2325 is output (for Models with Jam Protection Function on 4 Windows)
A
DTC B2325 is output (for Models with Jam Protection Function on Driver Door Window Only)
B
DTC B2325 is not output
C
|
|
||||
|
|
||||
| A | |
| 3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MASTER SWITCH) |
Disconnect the E3 ECU connector.

Disconnect the I11*1 or I22*2 switch connector.
- HINT:
- *1: for LHD
- *2: for RHD
Measure the resistance and voltage according to the value(s) in the tables below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E3-10 (LIN2) - I11-17 (LIN1)*1 or I22-17 (LIN1)*2
Always
Below 1 Ω
E3-10 (LIN2) - Body ground
Always
10 kΩ or higher
- Standard Voltage:
Tester Connection
Condition
Specified Condition
E3-10 (LIN2) - Body ground
Always
Below 1 V
|
|
||||
| OK | |
| 4. CLEAR DTC |
Reconnect the E3 ECU connector.
Disconnect the I11*1 or I22*2 switch connector.
- HINT:
- *1: for LHD
- *2: for RHD
Clear the DTC (Click here).
| NEXT | |
| 5. CHECK FOR DTC |
Recheck for DTCs (Click here).
Result Result
Proceed to
DTC B2325 is output
A
DTC B2325 is not output
B
|
|
||||
| A | |
| 6. CLEAR DTC |
Reconnect the I11*1 or I22*2 switch connector.
- HINT:
- *1: for LHD
- *2: for RHD
Disconnect the I12 motor connector.
Clear the DTC (Click here).
| NEXT | |
| 7. CHECK FOR DTC |
Recheck for DTCs (Click here).
Result Result
Proceed to
DTC B2325 is output
A
DTC B2325 is not output
B
|
|
||||
| A | |
| 8. CLEAR DTC |
Reconnect the I12 motor connector.
Disconnect the I4 motor connector.
Clear the DTC (Click here).
| NEXT | |
| 9. CHECK FOR DTC |
Recheck for DTCs (Click here).
Result Result
Proceed to
DTC B2325 is output
A
DTC B2325 is not output
B
|
|
||||
| A | |
| 10. CLEAR DTC |
Reconnect the I4 motor connector.
Disconnect the J4 motor connector.
Clear the DTC (Click here).
| NEXT | |
| 11. CHECK FOR DTC |
Recheck for DTCs (Click here).
Result Result
Proceed to
DTC B2325 is output
A
DTC B2325 is not output
B
|
|
||||
| A | |
| 12. CLEAR DTC |
Reconnect the J4 motor connector.
Disconnect the J11 motor connector.
Clear the DTC (Click here).
| NEXT | |
| 13. CHECK FOR DTC |
Recheck for DTCs (Click here).
Result Result
Proceed to
DTC B2325 is output (w/ Double Locking System)
A
DTC B2325 is output (w/o Double Locking System, w/ Sliding Roof System)
B
DTC B2325 is output (w/o Double Locking System, w/o Sliding Roof System)
C
DTC B2325 is not output
D
|
|
||||
|
|
||||
|
|
||||
| A | |
| 14. CLEAR DTC |
Reconnect the J11 motor connector.
Disconnect the E86 relay connector.
Clear the DTC (Click here).
| NEXT | |
| 15. CHECK FOR DTC |
Recheck for DTC (Click here).
Result Result
Proceed to
DTC B2325 is output (w/ Sliding Roof System)
A
DTC B2325 is output (w/o Sliding Roof System)
B
DTC B2325 is not output (for LHD)
C
DTC B2325 is not output (for RHD)
D
|
|
||||
|
|
||||
|
|
||||
| A | |
| 16. CLEAR DTC |
Reconnect the E86 relay connector.
Disconnect the R5 ECU connector.
Clear the DTC (Click here).
| NEXT | |
| 17. CHECK FOR DTC |
Recheck for DTCs (Click here).
Result Result
Proceed to
DTC B2325 is output
A
DTC B2325 is not output
B
|
|
||||
| A | ||
| ||
| 18. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT POWER WINDOW REGULATOR MOTOR) |
Disconnect the E3 ECU connector.

Disconnect the I12*1 or I4*2 motor connector.
- HINT:
- *1: for LHD
- *2: for RHD
Measure the resistance and voltage according to the value(s) in the tables below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E3-10 (LIN2) - I12-9 (LIN)*1 or I4-9 (LIN)*2
Always
Below 1 Ω
|
|
||||
| OK | |
| 19. CLEAR DTC |
Reconnect the E3 ECU connector.
Disconnect the I12*1 or I4*2 motor connector.
- HINT:
- *1: for LHD
- *2: for RHD
Clear the DTC (Click here).
| NEXT | |
| 20. CHECK FOR DTC |
Recheck for DTCs (Click here).
Result Result
Proceed to
DTC B2325 is output
A
DTC B2325 is not output (for LHD)
B
DTC B2325 is not output (for RHD)
C
|
|
||||
|
|
||||
| A | |
| 21. CLEAR DTC |
Reconnect the I12*1 or I4*2 motor connector.
- HINT:
- *1: for LHD
- *2: for RHD
Disconnect the E86 relay connector.
Clear the DTC (Click here).
| NEXT | |
| 22. CHECK FOR DTC |
Recheck for DTCs (Click here).
Result Result
Proceed to
DTC B2325 is output
A
DTC B2325 is not output (for LHD)
B
DTC B2325 is not output (for RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||
