2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

B15F7 Certification ECU Vehicle Information Reading/Writing Process Malfunction

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

This DTC is stored when items controlled by the certification ECU (smart key ECU assembly) cannot be customized via the navigation system vehicle customization screen.

HINT:
The certification ECU (smart key ECU assembly) controls the items for the following systems that are customizable via the navigation system screen:
  1. Entry and start system (for Entry Function)
  2. Entry and start system (for Start Function)

DTC No.
DTC Detection Condition
Trouble Area
B15F7
Certification ECU (smart key ECU assembly) vehicle setting processing error.
  1. CAN communication system
  2. Entry and start system (for entry function)
  3. Entry and start system (for start function)
  4. Certification ECU (smart key ECU assembly)
  5. Display and navigation module display

INSPECTION PROCEDURE


1. CHECK CAN COMMUNICATION SYSTEM
  1. Use the intelligent tester to check if the CAN communication system is functioning normally.

    HINT:
    1. for LHD (Click here)
    2. for RHD (Click here)

    OK:
    CAN communication DTC is not output.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
GO TO CAN COMMUNICATION SYSTEM (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2. CHECK ENTRY AND START SYSTEM (for Entry Function)
  1. Check if the entry and start system (for entry function) is malfunctioning (Click here).

    HINT:
    Customization may not be possible depending on the malfunction in the entry and start system (for entry function).

    OK:
    No malfunctions are present in the entry and start system (for entry function).



NG
GO TO ENTRY AND START SYSTEM (for Entry Function) (Click here)
OK


3. CHECK ENTRY AND START SYSTEM (for Start Function)
  1. Check if the entry and start system (for start function) is malfunctioning (Click here).

    HINT:
    Customization may not be possible depending on the malfunction in the entry and start system (for start function).

    OK:
    No malfunctions are present in the entry and start system (for start function).



NG
GO TO ENTRY AND START SYSTEM (for Start Function) (Click here)
OK


4. CHECK CUSTOMIZE ITEMS

  1. E194855E01
    Display the "Vehicle Customization" screen.

  1. Make a note of the customizable items for each certification ECU related system.

    HINT:
    These items shown as customizable via the navigation system vehicle customization screen can also be changed using the intelligent tester. In a following step, the intelligent tester will be used.

    1. To match-up the items in the navigation display with the items on the intelligent tester, check the customize parameters list for the entry and start system (for entry function) related items that can be customized via the navigation system screen (Click here).

    2. To match-up the items in the navigation display with the items on the intelligent tester, check the customize parameters list for the entry and start system (for start function) related items that can be customized via the navigation system screen (Click here).

  1. Using the intelligent tester, confirm that it is possible to change the settings of the customize parameters that are available for customization via the navigation system screen.

    OK:
    The items available for customization via the navigation system screen can be customized successfully using the intelligent tester.



NG
REPLACE SMART KEY ECU ASSEMBLY
OK

REPLACE DISPLAY AND NAVIGATION MODULE DISPLAY (Click here)


← B15F6 Main Body ECU Vehicle Information Reading/Writing Process Malfunction (Sep 2011 – Dec 2011)U0073 Control Module Communication Bus Off (+ U0155, U0164, U1110) (Sep 2011 – Dec 2011) →