2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

Image from Camera for Parking Assist Monitor is Abnormal

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

The display signal from the rear television camera assembly is transmitted to the display and navigation module display via the parking assist ECU.

WIRING DIAGRAM

E195772E02

INSPECTION PROCEDURE

NOTICE:
  1. When "System initializing" is displayed on the display and navigation module display after the battery terminal disconnected, correct the steering angle neutral point (Click here).
  2. Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (Click here).

HINT:
Images are difficult to discern even in normal conditions if:
  1. Noise may occur in the image depending on electrical devices used in the cabin.
  2. Noise may occur in the image if accessories that generate radio waves have been installed.
  3. The camera screen is frosted over (the image immediately after turning the engine switch on (IG) may be blurred or darker than normal).
  4. The camera lens is dirty with snow, mud, etc.
  5. A strong beam of light, such as a sunbeam or headlight, hits the camera.
  6. It is too dark around the camera (at night etc.).
  7. The ambient temperature around the camera is either too high or too low.
  8. The vehicle is tilted at a steep angle.
  9. The ambience of the camera is too bright. (When a strong light, such as a sunbeam reflected off the vehicle body, hits the camera, the image may be blurred. This is called the "SMEAR" phenomenon, peculiar to the CCD camera.)


1. CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - REAR TELEVISION CAMERA)
  1. Disconnect the F44 connector from the parking assist ECU.

  1. Disconnect the S5 connector from the rear television camera assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F44-34 (CV-) - S5-1 (CV-)
    Always
    Below 1 Ω
    F44-10 (CV+) - S5-2 (CV+)
    Always
    Below 1 Ω
    F44-35 (CB+) - S5-4 (CB+)
    Always
    Below 1 Ω
    F44-34 (CV-) - Body ground
    Always
    10 kΩ or higher
    F44-10 (CV+) - Body ground
    Always
    10 kΩ or higher
    F44-11 (CGND) - Body ground
    Always
    10 kΩ or higher
    F44-35 (CB+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. INSPECT PARKING ASSIST ECU (CV-, CGND)

  1. E153950E07
    Reconnect the F44 connector to the parking assist ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F44-34 (CV-) - Body ground
    Always
    Below 1 Ω
    F44-11 (CGND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Component with harness connected
    (Parking Assist ECU)



NG
REPLACE PARKING ASSIST ECU (Click here)
OK


3. INSPECT REAR TELEVISION CAMERA ASSEMBLY (CB+, CGND)
  1. Disconnect the S5 connector from the rear television camera assembly.

  1. E152756E09
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    S5-3 (CGND) - S5-4 (CB+)
    Engine switch on (IG)
    Shift lever in R
    5.8 to 7.0 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Rear Television Camera Assembly)



NG
REPLACE PARKING ASSIST ECU (Click here)
OK


4. INSPECT PARKING ASSIST ECU (CV+, GND1)
  1. Reconnect the S5 connector to the rear television camera assembly.

  1. Reconnect the F43 and F44 connectors to the parking assist ECU.E195583E04

  1. E171712E02
    Check the waveform of the rear television camera assembly using an oscilloscope.

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.

    OK:
    Waveform is as shown in the illustration.

    Item
    Content
    Terminal No. (Symbol)
    F44-10 (CV+) - F43-4 (GND1)
    Tool Setting
    200 mV/DIV., 50 μsec./DIV.
    Condition
    Engine switch on (IG), shift lever in R

    HINT:
    The video waveform changes according to the image sent by the rear television camera assembly.

    Text in Illustration 
    *1
    Component with harness connected
    (Parking Assist ECU)
    *2
    Waveform 1 (under normal conditions)
    *3
    Waveform 2 (camera lens is covered, blacking out the screen)
    *4
    Synchronized Signal
    *5
    Video Waveform



NG
REPLACE REAR TELEVISION CAMERA ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Images from All Cameras are Abnormal (Sep 2011 – Dec 2011)ECU Power Source Circuit (Sep 2011 – Dec 2011) →