The fuel pump circuit consists of the ECM, fuel pump and fuel pump ECU (which operates the fuel pump). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump ECU. Based on the signal sent from the ECM, the fuel pump ECU adjusts the fuel pump operation speed.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.
Check whether operating sounds can be heard while operating the fuel pump using the GTS.
Operating sounds can be heard from fuel pump.
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Disconnect the fuel pump ECU connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| N14-6 (+B) - Body Ground | Engine switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector
(to fuel pump ECU) |
OK
NG
Disconnect the fuel pump ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N14-3 (E) - Body ground | Always | Below 1 Ω |
OK
NG
Disconnect the fuel pump connector.
Disconnect the fuel pump ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N1-4 (B2) - N14-1 (FP) | Always | Below 1 Ω |
| N1-5 (E2) - N14-2 (FP-) | Always | Below 1 Ω |
| N1-4 (B2) or N14-1 (FP) - Body ground | Always | 10 kΩ or higher |
| N1-5 (E2) or N14-2 (FP-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Inspect the fuel pump (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL PUMP>INSPECTION).
OK
NG
Disconnect the fuel pump ECU connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N14-5 (FPC) - A52-52 (FPC) | Always | Below 1 Ω |
| N14-5 (FPC) or A52-52 (FPC) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N14-5 (FPC) - A38-52 (FPC) | Always | Below 1 Ω |
| N14-5 (FPC) or A38-52 (FPC) - Body ground | Always | 10 kΩ or higher |
OK
NG
Replace the fuel pump ECU (w/ Active Height Control) (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL PUMP ECU(w/ Active Height Control)>REMOVAL)
Replace the fuel pump ECU (w/o Active Height Control) (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL PUMP ECU(w/o Active Height Control)>REMOVAL)
NEXT
Check the fuel pump operation.
Malfunction has been repaired successfully.
OK
NG
Inspect the EFI NO.2 relay (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).
OK
NG
Remove the EFI NO.2 relay from the engine room relay block.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| EFI NO.2 relay (1) - Body ground | Engine switch on (IG) | 11 to 14 V |
| EFI NO.2 relay (5) - Body ground | Always | 11 to 14 V |
| *1 | Engine Room Relay Block: |
| *2 | EFI NO. 2 RELAY |
OK
NG
Remove the EFI NO.2 relay from the engine room relay block.
Disconnect the fuel pump ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| EFI NO.2 relay (3) - N14-6 (+B) | Always | Below 1 Ω |
| EFI NO.2 relay (3) or N14-6 (+B) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the cable from the negative (-) battery terminal.
Disconnect the cable from the positive (+) battery terminal.
Remove the EFI NO.2 relay from the engine room relay block.
Remove the No. 1 integration relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| EFI NO.2 relay (1) - 1B-4 | Always | Below 1 Ω |
| EFI NO.2 relay (5) - Battery positive (+) terminal | Always | Below 1 Ω |
| EFI NO.2 relay (2) - Body ground | Always | Below 1 Ω |
| EFI NO.2 relay (1) or 1B-4 - Body ground | Always | 10 kΩ or higher |
| EFI NO.2 relay (5) or Battery positive (+) terminal - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the fuel tank assembly (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL TANK>REMOVAL).
Remove the fuel pump from the fuel tank assembly.
Clean the fuel pump to completely remove any remaining fuel.
Connect the fuel pump connector.
Confirm that no fuel remains inside or on the outside of the fuel pump.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump Duty.
Operate the fuel pump using the active test function and measure the voltage according to the value(s) in the table below.
| Tester Connection | Tester Operation | Specified Condition |
|---|---|---|
| 1 - 2 | FPC Duty: 25% | 3.2 to 4.05 V |
| FPC Duty: 80% | 8.8 to 12.5 V |
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Operate the fuel pump using the active test function and measure the voltage according to the value(s) in the table below.
| Tester Connection | Tester Operation | Specified Condition |
|---|---|---|
| 1 - 2 | ON (FPC Duty: 90%) | 9.0 to 14.0 V |
Be sure to measure the voltage with all of the connectors connected.
Before performing this inspection, check that the battery voltage is between 11 and 14 V (not depleted).
| *a | Component with harness connected
(Fuel Pump) |
OK
NG
Disconnect the fuel pump ECU connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N14-5 (FPC) - A52-52 (FPC) | Always | Below 1 Ω |
| N14-5 (FPC) or A52-52 (FPC) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N14-5 (FPC) - A38-52 (FPC) | Always | Below 1 Ω |
| N14-5 (FPC) or A38-52 (FPC) - Body ground | Always | 10 kΩ or higher |
OK
NG
Replace the fuel pump (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL PUMP>REMOVAL).
NEXT
Replace the fuel pump ECU (w/ Active Height Control) (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL PUMP ECU(w/ Active Height Control)>REMOVAL)
Replace the fuel pump ECU (w/o Active Height Control) (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL PUMP ECU(w/o Active Height Control)>REMOVAL)
NEXT
Check the fuel pump operation.
Malfunction has been repaired successfully.
OK
NG