The crankshaft position sensor system consists of a crankshaft position sensor plate and a pickup coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of an iron core and magnet. The sensor plate rotates, and a pulse signal is created as each tooth passes by the pickup coil. The pickup coil generates 34 signals for each revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the common rail injection system is controlled.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Crank or start engine | When one of the following conditions is met (for 5 seconds during cranking or 0.5 seconds during engine start) (1 trip detection logic):
·
No crankshaft position sensor signal is sent to the ECM while cranking. |
·
Open or short in crankshaft position sensor circuit ·
Crankshaft position sensor ·
No. 1 crankshaft position sensor plate (crankshaft) ·
ECM |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Engine running at 1000 rpm or more with vehicle stationary | No crankshaft position sensor signal is input to the ECM for 0.05 seconds or more, and conditions (a), (b) and (c) are met (1 trip detection logic):
(a) Engine speed is 1000 rpm or more. (b) STA signal is off. (c) 3 seconds or more have elapsed after STA signal is switched from on to off. |
·
Open or short in crankshaft position sensor circuit ·
Crankshaft position sensor ·
No. 1 crankshaft position sensor plate (crankshaft) ·
ECM |
| DTC No. | Data List |
|---|---|
| P0335 | Engine Speed |
| P0339 |
If DTC P0335 and/or P0339 is stored, the following symptoms may appear:
Difficult starting
Misfire
Combustion noise
Black smoke
White smoke
Lack of power
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
The Data List item Engine Speed is calculated from the output of the crankshaft position sensor.
A DTC is also stored when the ground of a shielded wire is faulty.
Disconnect the crankshaft position sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (NE+) - 2 (NE-) | Cold | 1630 to 2740 Ω |
| 1 (NE+) - 2 (NE-) | Hot | 2065 to 3225 Ω |
In the table above, the terms "Cold" and "Hot" refer to the temperature of the coils in the sensor. "Cold" means approximately -10 to 50°C (14 to 122°F). "Hot" means approximately 50 to 100°C (122 to 212°F).
OK
NG
Disconnect the crankshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C65-1 (NE+) - C45-78 (NE+) | Always | Below 1 Ω |
| C65-2 (NE-) - C45-77 (NE-) | Always | Below 1 Ω |
| C65-3 - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C65-1 (NE+) - C46-78 (NE+) | Always | Below 1 Ω |
| C65-2 (NE-) - C46-77 (NE-) | Always | Below 1 Ω |
| C65-3 - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C65-1 (NE+) or C45-78 (NE+) - Body ground | Always | 10 kΩ or higher |
| C65-2 (NE-) or C45-77 (NE-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C65-1 (NE+) or C46-78 (NE+) - Body ground | Always | 10 kΩ or higher |
| C65-2 (NE-) or C46-77 (NE-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Check the sensor installation.
Sensor is installed correctly.
OK
NG
Check the teeth of the sensor plate.
The sensor plate teeth do not have any cracks or deformation.
OK
NG
Replace the ECM (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Replace the crankshaft position sensor (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>CRANKSHAFT POSITION SENSOR>REMOVAL).
NEXT
NEXT
Securely reinstall sensor (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>CRANKSHAFT POSITION SENSOR>INSTALLATION).
NEXT
Replace the No. 1 crankshaft position sensor plate (See page Engine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY).
NEXT
Connect the intelligent tester to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DTC CHECK / CLEAR).
Turn the ignition switch off.
Start the engine and run it at 1000 rpm or more.
Confirm that the DTC is not output again.
Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input DTC P0335 and/or P0339.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or UNKNOWN, after increasing the engine speed to 1000 rpm for approximately 1 second, idle the engine for 5 minutes.
NEXT