Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P0340  Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor)  


DESCRIPTION

The camshaft position sensor (G signal) consists of a magnet, iron core and pickup coil.

The G signal plate (No. 2 camshaft timing sprocket) has one tooth on its outer circumference and is installed on the camshaft timing chain gear. When the timing gear rotates, the protrusion on the signal plate and the air gap on the pickup coil change, causing fluctuations in the magnetic field that generate a voltage in the pickup coil.

The NE signal plate has 34 teeth and is mounted on the No. 1 crankshaft position sensor plate. The NE signal sensor generates 34 signals for every revolution. The ECM detects the camshaft angle based on the G signal, and detects the crankshaft angle based on the NE signal.

P0340
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Crank engine for 4 seconds (STA on) STA on:
No camshaft position sensor signal is sent to the ECM while cranking for 4 seconds or more (2 trip detection logic)
·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

Crankshaft position sensor

·

No. 2 camshaft timing sprocket

·

ECM


Idle engine for 1 second (STA off) STA off:
Either condition is met (1 trip detection logic):
·

Camshaft position sensor signal is not input with an engine speed of 500 rpm or more.

·

Phase deviation in crankshaft and camshaft position sensor signals with an engine speed of 500 to 3000 rpm occurs a certain number of times.



HINT:

If DTC P0340 is stored, the following symptoms may appear:

-

Difficulty starting

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power




CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION).



HINT:
·

After performing the inspection procedure for the crankshaft position sensor, if DTC P0340 is output again, check the following items related to the camshaft position sensor.

-

Installation condition of the camshaft position sensor

-

Installation condition of the camshaft

-

Connection of the camshaft position sensor connector



·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT CAMSHAFT POSITION SENSOR

OK

2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)

NG

7.REPLACE CAMSHAFT POSITION SENSOR
2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C66-1 - C45-80 (G+) Always Below 1 Ω
C66-2 - C45-79 (G-) Always Below 1 Ω
C66-1 or C45-80 (G+) - Body ground Always 10 kΩ or higher
C66-2 or C45-79 (G-) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C66-1 - C46-80 (G+) Always Below 1 Ω
C66-2 - C46-79 (G-) Always Below 1 Ω
C66-1 or C46-80 (G+) - Body ground Always 10 kΩ or higher
C66-2 or C46-79 (G-) - Body ground Always 10 kΩ or higher



d.

Reconnect the camshaft position sensor connector.


e.

Reconnect the ECM connector.



OK

3.CHECK CAMSHAFT POSITION SENSOR (SENSOR INSTALLATION)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK CAMSHAFT POSITION SENSOR (SENSOR INSTALLATION)
a.
A208464E01
0.401,1.758 0.649,1.91 0.249,0.152 10 OK 2.664,1.768 2.912,1.92 0.249,0.152 10 NG

Check the sensor installation.

OK:

Sensor is installed correctly.




OK

4.CHECK NO. 2 CAMSHAFT TIMING SPROCKET

NG

9.SECURELY REINSTALL SENSOR
4.CHECK NO. 2 CAMSHAFT TIMING SPROCKET
a.

Check the condition of the timing sprocket.

OK:

Timing sprocket does not have any cracks or deformation.




OK

5.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR CIRCUIT)

NG

10.REPLACE NO. 2 CAMSHAFT TIMING SPROCKET
5.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR CIRCUIT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for 30 seconds or more.


f.

Start the engine and idle it for 4 seconds or more.


g.

Turn the GTS on.


h.

Check the engine condition while wiggling the crankshaft position sensor wire harness for 4 seconds or more when idling.


i.

Enter the following menus: Engine and ECT / Trouble Codes.


j.

Read the DTCs.

Result
Result Proceed to
Except below A
There are problem such as rough idle or engine stall when wire harness is wiggled, or DTC is output* B

HINT:

*: As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).




A

6.REPLACE ECM

B

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE ECM

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPLACE CAMSHAFT POSITION SENSOR
a.


NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.SECURELY REINSTALL SENSOR

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE NO. 2 CAMSHAFT TIMING SPROCKET
a.

Replace the No. 2 camshaft timing sprocket (See page Engine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY).



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine and idle it for 4 seconds or more.


e.

Enter the following menus: Engine and ECT / Trouble Codes.


f.

Confirm that the DTC is not output again.



NEXT

END