Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P0100  Mass or Volume Air Flow Circuit  P0102  Mass or Volume Air Flow Circuit Low Input  P0103  Mass or Volume Air Flow Circuit High Input  


DESCRIPTION

The Mass Air Flow (MAF) meter uses a platinum hot wire. The mass air flow meter consists of a platinum hot wire, a temperature sensor and a control circuit installed in a plastic housing. The mass air flow meter hot wire and temperature sensor (located in the intake air by-pass of the housing) detect changes in the intake air temperature.

The hot wire is maintained at the predetermined temperature by controlling the current flow through the hot wire. This current flow is then used as the output voltage of the mass air flow meter.

The circuit is constructed so that the platinum hot wire and temperature sensor provide a bridge circuit, with the power transistor controlled so that the potential of A and B remains equal to maintain the predetermined temperature.

A160257E01
2.954,2.753 5.064,2.960 2.110,0.207 10 Temperature Sensor (Thermistor) 1.929,0.681 2.184,0.845 0.255,0.163 10 +B 1.878,1.033 2.969,1.179 1.091,0.145 10 Power Transistor 2.18,1.424 3.342,1.595 1.162,0.171 10 Hot Wire (Heater) 5.974,2.76 7.117,2.932 1.143,0.171 10 Hot Wire (Heater) 1.357,2.631 1.593,1.889 false 2.142,1.492 1.962,1.924 false 2.574,2.013 3.560,2.207 0.986,0.194 10 Output Voltage 4.646,2.733 5.424,1.969 false 6.322,2.003 6.116,2.746 false 1.323,1.911 1.487,2.075 0.164,0.165 10 A 2.133,1.904 2.299,2.072 0.165,0.168 10 B 4.967,3.273 6.151,3.439 1.184,0.165 10 Cold Film Element 0.474,2.638 1.658,2.803 1.184,0.165 10 Cold Film Element 5.507,3.235 5.794,1.968 false

P0100
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 3 seconds Mass air flow (MAF) meter voltage is 0.2 V or less, or 4.9 V or more with the engine speed at 4000 rpm or less for 3 seconds (1 trip detection logic).
·

Open or short in Mass Air Flow (MAF) meter circuit

·

Mass air flow meter

·

ECM



P0102
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 3 seconds MAF meter voltage is 0.2 V or less with the engine speed at 4000 rpm or less for 3 seconds (1 trip detection logic).
·

Open in Mass Air Flow (MAF) meter circuit

·

Mass air flow meter

·

ECM



P0103
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 3 seconds MAF meter voltage is 4.9 V or more with the engine speed at 4000 rpm or less for 3 seconds (1 trip detection logic).
·

Shot in Mass Air Flow (MAF) meter circuit

·

Mass air flow meter

·

ECM



Related Data List
DTC No. Data List
P0100 MAF
P0102
P0103

HINT:
·

If DTC P0100, and/or P0102 is stored, the following symptoms may appear (as the ECU mistakenly determines that there is less air than the actual intake air amount, EGR is decreased to match the target EGR):

-

Combustion noise worsens


·

If DTC P0100, and/or P0103 is stored, the following symptoms may appear (as the ECU mistakenly determines that there is more air than the actual intake air amount, EGR is increased to match the target EGR):

-

Misfire

-

White smoke

-

Black smoke


·

After confirming DTC P0100, P0102 or P0103, check the mass air flow ratio by entering the following menus: Powertrain / Engine / Data List / MAF.

Reference:
Air Flow Value (g/sec.) Malfunction
Approximately 0.0
·

Open in mass air flow meter power source circuit

·

Open or short in VG circuit


174.0 or more Open in EVG circuit



WIRING DIAGRAM

A182250E02
4.106,1.101 4.326,1.266 0.220,0.165 10 VG 5.066,1.101 5.286,1.266 0.220,0.165 10 VG 4.796,1.101 4.993,1.266 0.197,0.165 10 72 5.199,2.543 6.110,2.708 0.911,0.165 10 C45*1, C46*2 4.733,1.604 4.993,1.770 0.259,0.165 10 118 4.409,1.284 4.545,1.449 0.136,0.165 10 3 4.02,1.604 4.325,1.770 0.305,0.165 10 E2G 5.078,1.604 5.448,1.770 0.370,0.165 10 EVG 2.961,2.073 3.347,2.238 0.386,0.165 10 C50 0.968,2.64 1.734,2.806 0.766,0.165 10 *1: for LHD 0.968,2.97 1.734,3.135 0.766,0.165 10 *2: for RHD 2.961,2.245 4.265,2.410 1.304,0.165 10 Mass Air Flow Meter 4.408,1.782 4.546,1.949 0.138,0.167 10 2 2.878,0.785 3.098,0.950 0.220,0.165 10 +B 1.743,0.706 2.384,0.871 0.641,0.165 10 EFI NO. 2 0.432,0.867 1.332,1.042 0.901,0.175 10 from EFI relay 1.846,0.991 2.023,1.156 0.177,0.165 10 1 2.714,0.971 2.891,1.136 0.177,0.165 10 1 2.164,0.991 2.341,1.156 0.177,0.165 10 2 5.196,2.717 5.556,2.870 0.360,0.154 10 ECM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (MASS AIR FLOW RATE)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Data List / MAF.


d.

Read the value.

Result
Result Proceed to
0.0 A
174.0 or more B
Between 1 and 173.0* C


HINT:

*: The value should change when the throttle valve is opened or closed.



A

2.INSPECT MASS AIR FLOW METER (POWER SOURCE CIRCUIT)

B

8.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)

C

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.INSPECT MASS AIR FLOW METER (POWER SOURCE CIRCUIT)
U162841E01
0.099,0.04 2.436,0.377 2.336,0.336 10 Front view of wire harness connector: (to Mass Air Flow Meter) 1.379,2 0.955,2.45 false 0.796,2.493 1.050,2.676 0.254,0.184 10 +B 1.57,0.976 1.851,1.132 0.281,0.156 10 C50

a.

Disconnect the mass air flow meter connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C50-1 (+B) - Body ground Ignition switch ON 11 to 14 V




OK

3.INSPECT MASS AIR FLOW METER

NG

5.INSPECT FUSE (EFI NO. 2)
3.INSPECT MASS AIR FLOW METER

OK

4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

NG

11.REPLACE MASS AIR FLOW METER
4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.

A385076E01
1.688,0.854 2.135,1.104 0.448,0.25 4.208,0.833 4.656,1.083 0.448,0.25 5.083,0.823 5.531,1.073 0.448,0.25 2.292,2.167 1.948,1.688 true 1.438,2.156 1.771,1.688 true 4.26,2.25 4.51,1.896 true 4.802,2.219 4.51,1.75 true 0.823,0.094 3.125,0.479 2.302,0.385 10 false Front view of wire harness connector: (to Mass Air Flow Meter) 1.771,0.906 2.156,1.104 0.385,0.198 10 false C50 1.302,2.198 1.688,2.396 0.385,0.198 10 false E2G 2.25,2.198 2.635,2.396 0.385,0.198 10 false VG 3.802,0.083 6.104,0.469 2.302,0.385 10 false Front view of wire harness connector: (to ECM) 4.302,0.875 4.688,1.073 0.385,0.198 10 false C45 5.188,0.865 5.573,1.063 0.385,0.198 10 false C46 4.688,0.76 4.938,0.958 0.25,0.198 10 false *1 5.563,0.75 5.813,0.948 0.25,0.198 10 false *2 3.844,2.271 4.594,2.458 0.75,0.188 10 false 118 (EVG) 4.688,2.271 5.438,2.458 0.75,0.188 10 false 72 (VG) 0.135,2.052 0.938,2.26 0.802,0.208 10 false *1: for LHD 0.135,2.385 0.938,2.594 0.802,0.208 10 false *2: for RHD


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LHD
Tester Connection Condition Specified Condition
C50-3 (VG) - C45-72 (VG) Always Below 1 Ω
C50-2 (E2G) - C45-118 (EVG) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
C50-3 (VG) - C46-72 (VG) Always Below 1 Ω
C50-2 (E2G) - C46-118 (EVG) Always Below 1 Ω


Standard Resistance (Check for Short):
for LHD
Tester Connection Condition Specified Condition
C50-3 (VG) or C45-72 (VG) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C50-3 (VG) or C46-72 (VG) - Body ground Always 10 kΩ or higher




OK

10.REPLACE ECM

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.INSPECT FUSE (EFI NO. 2)
A182379E01
0.095,0.041 1.813,0.239 1.718,0.198 10 Engine Room Relay Block: 2.432,2.857 3.107,3.036 0.674,0.179 10 EFI NO. 2 2.335,2.28 2.756,2.817 false

a.

Remove the EFI NO. 2 fuse from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI NO. 2 fuse Always Below 1 Ω




OK

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ENGINE ROOM RELAY BLOCK)

NG

13.CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ENGINE ROOM RELAY BLOCK)
a.

Disconnect the mass air flow meter connector.

A385079E01
1.719,1.438 2.167,1.708 0.448,0.271 1.219,2.813 1.635,2.396 true 0.76,0.448 3.063,0.833 2.302,0.385 10 false Front view of wire harness connector: (to Mass Air Flow Meter) 3.771,0.115 6.24,0.479 2.469,0.365 10 false Component without harness connected: (Engine Room Relay Block) 1.802,1.49 2.26,1.688 0.458,0.198 10 false C50 1.031,2.844 1.49,3.042 0.458,0.198 10 false +B 4.75,2.938 5.438,3.156 0.688,0.219 10 false EFI NO. 2


b.

Remove the EFI NO. 2 fuse from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C50-1 (+B) - EFI NO. 2 fuse (2) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C50-1 (+B) or EFI NO. 2 fuse (2) - Body ground Always 10 kΩ or higher




OK

7.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK)

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK)
A385080E01
1.719,0.875 2.094,1.115 0.375,0.24 2.177,1.729 1.958,1.458 true 1.396,2.385 1.583,2.042 1.583,2.042 1.708,2.042 true 0.229,0.042 2.542,0.396 2.313,0.354 10 false Front view of wire harness connector: (to Engine Room Relay Block) 1.802,0.917 2.115,1.115 0.313,0.198 10 false 1B 2.208,1.698 2.521,1.896 0.313,0.198 10 false 4 1.74,1.938 2.854,2.135 1.115,0.198 10 true Integration Relay

a.

Remove the EFI NO. 2 fuse from the engine room relay block.


b.

Remove the integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
EFI NO. 2 fuse (1) - 1B-4 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
EFI NO. 2 fuse (1) or 1B-4 - Body ground Always 10 kΩ or higher




OK

14.CHECK ECM POWER SOURCE CIRCUIT

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
a.
U162842E01
0.092,0.096 2.429,0.432 2.336,0.336 10 Front view of wire harness connector: (to Mass Air Flow Meter) 1.523,2.011 1.071,2.566 false 0.912,2.581 1.332,2.765 0.420,0.184 10 E2G 1.577,1.048 1.858,1.204 0.281,0.156 10 C50

Disconnect the mass air flow meter connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C50-2 (E2G) - Body ground Always Below 1 Ω




OK

11.REPLACE MASS AIR FLOW METER

NG

9.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
9.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.

A385076E01
1.688,0.854 2.135,1.104 0.448,0.25 4.208,0.833 4.656,1.083 0.448,0.25 5.083,0.823 5.531,1.073 0.448,0.25 2.292,2.167 1.948,1.688 true 1.438,2.156 1.771,1.688 true 4.26,2.25 4.51,1.896 true 4.802,2.219 4.51,1.75 true 0.823,0.094 3.125,0.479 2.302,0.385 10 false Front view of wire harness connector: (to Mass Air Flow Meter) 1.771,0.906 2.156,1.104 0.385,0.198 10 false C50 1.302,2.198 1.688,2.396 0.385,0.198 10 false E2G 2.25,2.198 2.635,2.396 0.385,0.198 10 false VG 3.802,0.083 6.104,0.469 2.302,0.385 10 false Front view of wire harness connector: (to ECM) 4.302,0.875 4.688,1.073 0.385,0.198 10 false C45 5.188,0.865 5.573,1.063 0.385,0.198 10 false C46 4.688,0.76 4.938,0.958 0.25,0.198 10 false *1 5.563,0.75 5.813,0.948 0.25,0.198 10 false *2 3.844,2.271 4.594,2.458 0.75,0.188 10 false 118 (EVG) 4.688,2.271 5.438,2.458 0.75,0.188 10 false 72 (VG) 0.135,2.052 0.938,2.26 0.802,0.208 10 false *1: for LHD 0.135,2.385 0.938,2.594 0.802,0.208 10 false *2: for RHD


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LHD
Tester Connection Condition Specified Condition
C50-3 (VG) - C45-72 (VG) Always Below 1 Ω
C50-2 (E2G) - C45-118 (EVG) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
C50-3 (VG) - C46-72 (VG) Always Below 1 Ω
C50-2 (E2G) - C46-118 (EVG) Always Below 1 Ω


Standard Resistance (Check for Short):
for LHD
Tester Connection Condition Specified Condition
C50-3 (VG) or C45-72 (VG) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C50-3 (VG) or C46-72 (VG) - Body ground Always 10 kΩ or higher




OK

10.REPLACE ECM

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.REPLACE ECM

NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPLACE MASS AIR FLOW METER

NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE

NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.CHECK ECM POWER SOURCE CIRCUIT

NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON for 3 seconds


e.

Enter the following menus: Powertrain / Engine / DTC.


f.

Confirm that the DTC is not output again.



NEXT

END