Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle has been driven at 20 km/h (12.4 mph) or more for more than 20 seconds.

P0617
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Drive vehicle for 25 seconds or more at a speed of 20 km/h (12.4 mph) or more and an engine speed of 1000 rpm or more Conditions (a), (b) and (c) are met for 20 seconds
(a) Vehicle speed is more than 20 km/h (12.4 mph).
(b) Engine speed is more than 1000 rpm.
(c) STA signal is on.
·

Park/neutral position switch (A/T)

·

Starter relay circuit

·

Clutch start switch (M/T)



Related Data List
DTC No. Data List
P0617 Starter Signal

WIRING DIAGRAM

U163457E02
5.938,6.813 6.479,7.021 0.542,0.208 10 false ECM 5.667,2.563 6.167,2.792 0.5,0.229 10 false STSW 5.667,2.927 6.188,3.146 0.521,0.219 10 false ACCR 5.323,2.604 5.604,2.76 0.281,0.156 10 false A52 5.292,2.938 5.677,3.156 0.385,0.219 10 false A52 2.125,6 4.063,6.188 1.938,0.188 10 false Park/Neutral Position Switch*1 2.125,5.854 2.438,6.021 0.313,0.167 10 false C24 2.438,7.323 2.656,7.51 0.219,0.188 10 false ST 1.604,0.99 1.875,1.135 0.271,0.146 10 false 1C 1.969,1.115 2.688,1.281 0.719,0.167 10 false IG2 MAIN 2.938,0.521 3.271,0.688 0.333,0.167 10 false IG2 1.667,0.76 1.813,0.917 0.146,0.156 10 false 1 1.073,8.042 1.688,8.229 0.615,0.188 10 false Battery 3.729,7.802 4.208,7.958 0.479,0.156 10 false Starter 3.01,7.615 3.333,7.792 0.323,0.177 10 false D13 3.313,7.438 3.625,7.594 0.313,0.156 10 false D12 3.479,7.219 3.615,7.375 0.135,0.156 10 false 1 3.083,7.417 3.219,7.573 0.135,0.156 10 false 1 2.948,5.427 3.063,5.583 0.115,0.156 10 false 4 2.917,4.417 3.031,4.573 0.115,0.156 10 false 1 2.156,5.438 2.271,5.615 0.115,0.177 10 false 5 2.156,4.438 2.271,4.615 0.115,0.177 10 false 2 4.76,1.771 5.156,1.948 0.396,0.177 10 false IGN 4.542,1.615 4.656,1.792 0.115,0.177 10 false 1 4.542,1.99 4.656,2.167 0.115,0.177 10 false 2 4.427,3.896 4.604,4.042 0.177,0.146 10 false 5 4.74,4.74 4.885,4.917 0.146,0.177 10 false 1 4.427,4.74 4.573,4.917 0.146,0.177 10 false 3 4.74,3.896 4.906,4.052 0.167,0.156 10 false 2 1.604,1.333 1.854,1.479 0.25,0.146 10 false 1B 1.667,1.156 1.813,1.313 0.146,0.156 10 false 7 3.604,1 3.875,1.146 0.271,0.146 10 false 1B 3.656,0.802 3.802,0.958 0.146,0.156 10 false 8 3.615,1.323 3.885,1.469 0.271,0.146 10 false 1B 3.667,1.146 3.813,1.302 0.146,0.156 10 false 6 2.104,1.74 3.292,1.938 1.188,0.198 10 false Integration Relay 0.104,0.042 3.24,0.271 3.135,0.229 12 false w/ Entry and Start System: 2.052,4.01 3.177,4.219 1.125,0.208 10 false Main Body ECU 2.542,2.26 2.948,2.427 0.406,0.167 10 false IG2D 2.479,2.604 2.948,2.76 0.469,0.156 10 false STSW 2.479,2.938 2.938,3.104 0.458,0.167 10 false ACCR 2.5,3.281 2.969,3.438 0.469,0.156 10 false STR2 2.583,3.635 3.021,3.792 0.438,0.156 10 false STR 3.021,2.271 3.292,2.438 0.271,0.167 10 false E2 3.021,2.604 3.313,2.76 0.292,0.156 10 false E4 3.031,2.938 3.323,3.104 0.292,0.167 10 false E2 3.021,3.281 3.313,3.438 0.292,0.156 10 false E4 3.021,3.625 3.281,3.781 0.26,0.156 10 false E1 3.031,2.083 3.302,2.25 0.271,0.167 10 false 11 3.073,2.438 3.365,2.594 0.292,0.156 10 false 4 3.073,2.771 3.365,2.938 0.292,0.167 10 false 3 3.073,3.104 3.365,3.26 0.292,0.156 10 false 6 3.073,3.448 3.333,3.604 0.26,0.156 10 false 8 5.667,3.385 6.146,3.594 0.479,0.208 10 false STAR 5.302,3.396 5.667,3.552 0.365,0.156 10 false C46 5.677,5.51 6.156,5.677 0.479,0.167 10 false NSW 5.688,6.354 6.177,6.51 0.49,0.156 10 false STA 5.323,5.542 5.656,5.698 0.333,0.156 10 false A52 5.323,6.396 5.604,6.552 0.281,0.156 10 false A52 1.302,4.719 1.521,4.906 0.219,0.188 10 false ST 0.979,4.521 1.135,4.708 0.156,0.188 10 false 1 0.969,4.854 1.125,5.042 0.156,0.188 10 false 2 2.104,6.885 2.219,7.031 0.115,0.146 10 false 5 2.885,6.573 3.031,6.75 0.146,0.177 10 false 1 2.885,6.885 3.031,7.063 0.146,0.177 10 false 3 2.104,6.573 2.271,6.729 0.167,0.156 10 false 2 4.938,4.26 5.542,4.448 0.604,0.188 10 false ST CUT 2.146,4.865 2.563,5.031 0.417,0.167 10 false A49*3 2.125,5.01 3.521,5.198 1.396,0.188 10 false Clutch Start Switch*2 3.281,5.656 3.479,5.833 0.198,0.177 10 false *1 1.802,5.656 2,5.833 0.198,0.177 10 false *1 3.24,4.667 3.438,4.844 0.198,0.177 10 false *2 1.833,4.667 2.031,4.844 0.198,0.177 10 false *2 5.198,7.49 7.125,7.688 1.927,0.198 10 false *1: for Automatic transmission 5.198,7.792 7.125,7.99 1.927,0.198 10 false *2: for Manual transmission 2.333,5.448 2.448,5.625 0.115,0.177 10 false L 2.75,5.438 2.896,5.615 0.146,0.177 10 false B 5.198,8.083 7.125,8.281 1.927,0.198 10 false *3: for LHD 5.198,8.385 7.125,8.583 1.927,0.198 10 false *4: for RHD 4.969,2.604 5.25,2.76 0.281,0.156 10 false A38 4.948,2.938 5.323,3.146 0.375,0.208 10 false A38 4.948,2.771 5.302,2.917 0.354,0.146 10 false 13*3 4.948,2.417 5.26,2.583 0.313,0.167 10 false 14*3 4.958,3.396 5.323,3.552 0.365,0.156 10 false C45 4.917,3.198 5.271,3.344 0.354,0.146 10 false 51*3 4.979,5.542 5.313,5.698 0.333,0.156 10 false A38 4.979,6.396 5.26,6.552 0.281,0.156 10 false A38 4.948,5.323 5.323,5.51 0.375,0.188 10 false 43*3 4.927,6.198 5.302,6.354 0.375,0.156 10 false 48*3 5.313,2.771 5.667,2.917 0.354,0.146 10 false 13*4 5.313,2.427 5.625,2.594 0.313,0.167 10 false 14*4 5.26,3.188 5.677,3.365 0.417,0.177 10 false 51*4 5.313,5.323 5.729,5.531 0.417,0.208 10 false 43*4 5.26,6.188 5.656,6.344 0.396,0.156 10 false 48*4 2.615,4.865 3.031,5.031 0.417,0.167 10 false e1*4

U163745E02
6.375,7.594 6.708,7.75 0.333,0.156 10 false ECM 3.375,4.667 4.75,4.833 1.375,0.167 10 false Clutch Start Switch*2 3.99,7.385 4.208,7.573 0.219,0.188 10 false ST 1.604,1.052 1.875,1.198 0.271,0.146 10 false 1C 1.969,1.188 2.677,1.354 0.708,0.167 10 false IG2 MAIN 2.938,0.542 3.271,0.708 0.333,0.167 10 false IG2 1.667,0.854 1.813,1.01 0.146,0.156 10 false 1 0.635,8.156 1.094,8.344 0.458,0.188 10 false Battery 5.094,7.875 5.573,8.031 0.479,0.156 10 false Starter 4.365,7.708 4.688,7.885 0.323,0.177 10 false D13 4.677,7.51 4.99,7.667 0.313,0.156 10 false D12 4.833,7.313 4.969,7.469 0.135,0.156 10 false 1 4.438,7.51 4.573,7.667 0.135,0.156 10 false 1 4.469,4.125 4.583,4.281 0.115,0.156 10 false 1 3.708,4.125 3.823,4.302 0.115,0.177 10 false 2 4.646,1.167 5.042,1.344 0.396,0.177 10 false IGN 4.563,0.885 4.677,1.063 0.115,0.177 10 false 1 4.854,0.885 4.969,1.063 0.115,0.177 10 false 2 1.604,1.396 1.885,1.542 0.281,0.146 10 false 1B 1.667,1.229 1.813,1.385 0.146,0.156 10 false 7 3.604,1.031 3.875,1.177 0.271,0.146 10 false 1B 3.656,0.854 3.802,1.01 0.146,0.156 10 false 8 3.615,1.406 3.885,1.552 0.271,0.146 10 false 1B 3.667,1.24 3.813,1.396 0.146,0.156 10 false 6 2.104,1.823 3.323,2.021 1.219,0.198 10 false Integration Relay 0.104,0.021 6.01,0.25 5.906,0.229 12 false w/o Entry and Start System: 6.115,5.198 6.594,5.365 0.479,0.167 10 false NSW 5.76,5.229 6.094,5.385 0.333,0.156 10 false A52 3.667,6.958 3.844,7.104 0.177,0.146 10 false 5 4.448,6.646 4.594,6.823 0.146,0.177 10 false 1 4.448,6.958 4.594,7.135 0.146,0.177 10 false 3 3.667,6.646 3.833,6.802 0.167,0.156 10 false 2 3.396,5.667 5.448,5.875 2.052,0.208 10 false Park/Neutral Position Switch*1 3.385,5.521 3.698,5.688 0.313,0.167 10 false C24 4.469,5.104 4.583,5.26 0.115,0.156 10 false 4 3.708,5.104 3.823,5.281 0.115,0.177 10 false 5 1.948,7.26 2.167,7.448 0.219,0.188 10 false ST 1.865,6.917 2.01,7.094 0.146,0.177 10 false 1 2.156,6.917 2.323,7.073 0.167,0.156 10 false 2 6.115,6.24 6.594,6.406 0.479,0.167 10 false STA 5.76,6.271 6.094,6.427 0.333,0.156 10 false A52 6.115,1.031 6.594,1.198 0.479,0.167 10 false IGSW 5.76,1.063 6.094,1.219 0.333,0.156 10 false A52 0.76,3.24 0.875,3.417 0.115,0.177 10 false 1 1.052,3.24 1.167,3.417 0.115,0.177 10 false 2 1.979,2.646 2.292,2.792 0.313,0.146 10 false AM1 1.969,3.521 2.281,3.667 0.313,0.146 10 false AM2 2.531,3.521 2.844,3.667 0.313,0.146 10 false IG2 2.563,2.646 2.875,2.792 0.313,0.146 10 false ST1 1.479,2.719 1.792,2.865 0.313,0.146 10 false AM1 0.813,3.552 1.125,3.698 0.313,0.146 10 false AM2 0.573,2.698 0.885,2.844 0.313,0.146 10 false ALT 1.792,4.333 2.948,4.729 1.156,0.396 10 false Ignition or Starter Switch Assembly 1.792,4.188 2.094,4.344 0.302,0.156 10 false E93 0.646,5.063 2.771,5.229 2.125,0.167 10 false *1: for Automatic transmission 0.646,5.365 2.583,5.531 1.938,0.167 10 false *2: for Manual transmission 4.802,5.115 5,5.271 0.198,0.156 10 false *1 3.292,5.115 3.49,5.271 0.198,0.156 10 false *1 4.802,4.125 5,4.281 0.198,0.156 10 false *2 3.292,4.125 3.49,4.281 0.198,0.156 10 false *2 1.823,2.396 1.969,2.552 0.146,0.156 10 false 4 2.875,2.396 3.021,2.552 0.146,0.156 10 false 3 1.813,3.292 1.958,3.448 0.146,0.156 10 false 5 2.865,3.281 3.01,3.438 0.146,0.156 10 false 6 0.969,2.719 1.406,2.865 0.438,0.146 10 false LH J/B 5.417,5.219 5.75,5.375 0.333,0.156 10 false A38 5.375,5.021 5.698,5.188 0.323,0.167 10 false 43*3 5.417,6.271 5.75,6.427 0.333,0.156 10 false A38 5.375,6.073 5.688,6.24 0.313,0.167 10 false 48*3 5.417,1.073 5.75,1.229 0.333,0.156 10 false A38 5.375,0.865 5.698,1.031 0.323,0.167 10 false 28*3 0.646,5.656 1.458,5.823 0.813,0.167 10 false *3: for LHD 0.646,5.958 1.49,6.125 0.844,0.167 10 false *4: for RHD 5.75,5.042 6.073,5.208 0.323,0.167 10 false 43*4 5.75,6.073 6.063,6.24 0.313,0.167 10 false 48*4 5.75,0.865 6.073,1.031 0.323,0.167 10 false 28*4 3.885,5.125 4,5.302 0.115,0.177 10 false L 4.313,5.135 4.427,5.313 0.115,0.177 10 false B 3.427,4.51 3.854,4.677 0.427,0.167 10 false A49*3 3.917,4.521 4.333,4.688 0.417,0.167 10 false e1*4

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).


HINT:
·

The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to the Problem Symptoms Table (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>PROBLEM SYMPTOMS TABLE).

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM
a.

Check if the vehicle is equipped with the entry and start system.

Result
Result Proceed to
w/ Entry and Start System A
w/o Entry and Start System B



A

2.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)

B

10.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
2.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Data List / All Data / Starter Signal.


d.

Check the value displayed on the tester when the ignition switch is turned to ON and the engine is started.

OK:
Ignition Switch Condition Starter Signal
ON OFF
Engine started ON


Result
Result Proceed to
NG (A/T) A
NG (M/T) B
OK C



A

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

B

5.INSPECT CLUTCH START SWITCH

C

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).

Result
Result Proceed to
NG A
OK B



A

4.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

B

8.CHECK HARNESS AND CONNECTOR (PNP SWITCH OR CLUTCH START SWITCH - STA TERMINAL OF ECM)
4.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NEXT

7.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
5.INSPECT CLUTCH START SWITCH
a.

Check the clutch start switch (for LHD) (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH(for LHD)>INSPECTION).


b.

Check the clutch start switch (for RHD) (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH(for RHD)>INSPECTION).


Result
Result Proceed to
NG A
OK B


A

6.REPLACE CLUTCH START SWITCH

B

8.CHECK HARNESS AND CONNECTOR (PNP SWITCH OR CLUTCH START SWITCH - STA TERMINAL OF ECM)
6.REPLACE CLUTCH START SWITCH
a.

Replace the clutch start switch (for LHD) (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH(for LHD)>REMOVAL).


b.

Replace the clutch start switch (for RHD) (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH(for RHD)>REMOVAL).



NEXT

7.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
7.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Data List / All Data / Starter Signal.


d.

Check the value displayed on the tester when the ignition switch is turned to ON and the engine is started.

OK:
Ignition Switch Condition Starter Signal
ON OFF
Engine started ON


Result
Result Proceed to
NG A
OK B



A

8.CHECK HARNESS AND CONNECTOR (PNP SWITCH OR CLUTCH START SWITCH - STA TERMINAL OF ECM)

B

SYSTEM OK

8.CHECK HARNESS AND CONNECTOR (PNP SWITCH OR CLUTCH START SWITCH - STA TERMINAL OF ECM)

OK

9.CHECK WHETHER DTC OUTPUT RECURS

NG

REPLACE HARNESS OR CONNECTOR

9.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.



e.

Drive the vehicle at 20 km/h (12.4 mph) or more for 20 seconds or more.


f.

Enter the following menus: Powertrain / Engine / DTC.


g.

Read the DTCs.

Result
Display (DTC Output) Proceed to
P0617 A
No output B



A

B

SYSTEM OK

10.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Data List / All Data / Starter Signal.


d.

Check the value displayed on the tester when the ignition switch is turned to ON and the engine is started.

OK:
Ignition Switch Condition Starter Signal
ON OFF
Engine started ON


Result
Result Proceed to
NG (A/T) A
NG (M/T) B
OK C



A

11.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

B

13.INSPECT CLUTCH START SWITCH ASSEMBLY

C

11.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).

Result
Result Proceed to
NG A
OK B



A

12.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

B

15.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
12.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NEXT

17.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
13.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Check the clutch start switch (for LHD) (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH(for LHD)>INSPECTION).


b.

Check the clutch start switch (for RHD) (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH(for RHD)>INSPECTION).


Result
Result Proceed to
NG A
OK B


A

14.REPLACE CLUTCH START SWITCH ASSEMBLY

B

15.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
14.REPLACE CLUTCH START SWITCH ASSEMBLY
a.

Replace the clutch start switch (for LHD) (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH(for LHD)>REMOVAL).


b.

Replace the clutch start switch (for RHD) (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH(for RHD)>REMOVAL).



NEXT

17.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
15.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the Ignition or Starter Switch Assembly (See page Engine / Hybrid System>1VD-FTV (STARTING)>IGNITION SWITCH>INSPECTION).


Result
Result Proceed to
NG A
OK B


A

16.REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

B

18.CHECK HARNESS AND CONNECTOR (PNP SWITCH OR CLUTCH START SWITCH - STA TERMINAL OF ECM)
16.REPLACE IGNITION OR STARTER SWITCH ASSEMBLY
a.

Replace the Ignition or Starter Switch Assembly (See page Engine / Hybrid System>1VD-FTV (STARTING)>IGNITION SWITCH>REMOVAL).



NEXT

17.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
17.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Data List / All Data / Starter Signal.


d.

Check the value displayed on the tester when the ignition switch is turned to ON and the engine is started.

OK:
Ignition Switch Condition Starter Signal
ON OFF
Engine started ON


Result
Result Proceed to
NG A
OK B



A

18.CHECK HARNESS AND CONNECTOR (PNP SWITCH OR CLUTCH START SWITCH - STA TERMINAL OF ECM)

B

SYSTEM OK

18.CHECK HARNESS AND CONNECTOR (PNP SWITCH OR CLUTCH START SWITCH - STA TERMINAL OF ECM)

OK

19.CHECK WHETHER DTC OUTPUT RECURS

NG

REPLACE HARNESS OR CONNECTOR

19.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.



e.

Drive the vehicle at 20 km/h (12.4 mph) or more for 20 seconds or more.


f.

Enter the following menus: Powertrain / Engine / DTC.


g.

Read the DTCs.

Result
Display (DTC Output) Proceed to
P0617 A
No output B



A

B

SYSTEM OK