The ECM constantly generates 5 V of power from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.
When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.
Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON. The MIL goes off when the engine is started.
For the circuit diagram of the ECM power source circuit (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>ECM Power Source Circuit)
VC Power Source Circuit
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).
Connect the GTS to the DLC3.
Turn the ignition switch to ON and GTS on.
Check the communication between the GTS and ECM.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (EFI No. 2 fuse) - Body ground | Ignition switch ON | 11 to 14 V |
| *1 | Engine Room Relay Block |
| *2 | EFI No. 2 Fuse |
If the result is not as specified, since current is not flowing to the +B and +B2 terminals of the ECM, the system may not be started.
OK
NG
Disconnect the throttle position sensor (for Bank 1) connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
|---|---|
| Communication is possible | A |
| Communication is not possible | B |
Reconnect the throttle position sensor (for Bank 1) connector.
B
A
Disconnect the throttle position sensor (for Bank 2) connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
|---|---|
| Communication is possible | A |
| Communication is not possible | B |
Reconnect the throttle position sensor (for Bank 2) connector.
B
A
Disconnect the No. 1 EGR valve connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
|---|---|
| Communication is possible | A |
| Communication is not possible | B |
Reconnect the No. 1 EGR valve connector.
B
A
Disconnect the No. 2 EGR valve connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
|---|---|
| Communication is possible | A |
| Communication is not possible | B |
Reconnect the No. 2 EGR valve connector.
B
A
Disconnect the accelerator pedal position sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
|---|---|
| Communication is possible | A |
| Communication is not possible | B |
Reconnect the accelerator pedal position sensor connector.
B
A
Disconnect the manifold absolute pressure sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
|---|---|
| Communication is possible | A |
| Communication is not possible | B |
Reconnect the manifold absolute pressure sensor connector.
B
A
Disconnect the fuel pressure sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
|---|---|
| Communication is possible | A |
| Communication is not possible | B |
Reconnect the fuel pressure sensor connector.
B
A
Disconnect the nozzle vane position sensor (for Bank 1) connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
|---|---|
| Communication is possible | A |
| Communication is not possible | B |
Reconnect the nozzle vane position sensor (for Bank 1) connector.
B
A
(See pageEngine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>REMOVAL)
Disconnect the nozzle vane position sensor (for Bank 2) connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
|---|---|
| Communication is possible | A |
| Communication is not possible | B |
Reconnect the nozzle vane position sensor (for Bank 2) connector.
B
A
(See pageEngine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>REMOVAL)
Disconnect the throttle position sensor (for Bank 1) connector.
Disconnect the throttle position sensor (for Bank 2) connector.
Disconnect the No. 1 EGR valve connector.
Disconnect the No. 2 EGR valve connector.
Disconnect the accelerator pedal position sensor connector.
Disconnect the manifold absolute pressure sensor connector.
Disconnect the fuel pressure sensor connector.
Disconnect the nozzle vane position sensor (for Bank 1) connector.
Disconnect the nozzle vane position sensor (for Bank 2) connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C45-91 (VC) - Body ground | Always | 10 kΩ or higher |
| C45-110 (VCVL) - Body ground | Always | 10 kΩ or higher |
| C45-118 (VCM) - Body ground | Always | 10 kΩ or higher |
| C45-120 (VNVC) - Body ground | Always | 10 kΩ or higher |
| C45-66 (VCPM) - Body ground | Always | 10 kΩ or higher |
| A38-55 (VCPA) - Body ground | Always | 10 kΩ or higher |
| A38-56 (VCP2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C46-91 (VC) - Body ground | Always | 10 kΩ or higher |
| C46-110 (VCVL) - Body ground | Always | 10 kΩ or higher |
| C46-118 (VCM) - Body ground | Always | 10 kΩ or higher |
| C46-120 (VNVC) - Body ground | Always | 10 kΩ or higher |
| C46-66 (VCPM) - Body ground | Always | 10 kΩ or higher |
| A52-55 (VCPA) - Body ground | Always | 10 kΩ or higher |
| A52-56 (VCP2) - Body ground | Always | 10 kΩ or higher |
Reconnect the throttle position sensor (for Bank 1) connector.
Reconnect the throttle position sensor (for Bank 2) connector.
Reconnect the No. 1 EGR valve connector.
Reconnect the No. 2 EGR valve connector.
Reconnect the accelerator pedal position sensor connector.
Reconnect the manifold absolute pressure sensor connector.
Reconnect the fuel pressure sensor connector.
Reconnect the nozzle vane position sensor (for Bank 1) connector.
Reconnect the nozzle vane position sensor (for Bank 2) connector.
Reconnect the ECM connectors.
OK
NG