Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P062D  Fuel Injector Driver Circuit Performance Bank1  P062E  Fuel Injector Driver Circuit Performance Bank2  


DESCRIPTION

The EDU delivers drive signals to fuel injectors using the DC/DC converter, which provides a high-voltage and quick-charging system.

Soon after the EDU receives a fuel injection command (IJT) signal from the ECM, the EDU responds to the command with an injector injection confirmation (IJF) signal when the current is applied to the fuel injector.

U162931E02
0.115,0.083 2.885,0.313 2.771,0.229 10 false No. 1 Injector Driver (EDU) Wiring Diagram: 0.458,1.24 1.521,1.406 1.063,0.167 10 false from EDU Relay 1.146,2.292 2.24,2.49 1.094,0.198 10 false Command Pulse 0.563,3.177 0.979,3.375 0.417,0.198 10 false ECM 1.479,2.802 1.833,3 0.354,0.198 10 false IJt#1 1.552,4.177 1.813,4.375 0.26,0.198 10 false IJf 2.594,6.938 2.948,7.125 0.354,0.188 10 false C74 4.313,6.938 4.594,7.115 0.281,0.177 10 false C73 1.479,3.844 1.833,4.042 0.354,0.198 10 false IJt#7 1.479,3.49 1.833,3.688 0.354,0.198 10 false IJt#6 1.479,3.146 1.844,3.344 0.365,0.198 10 false IJt#4 0.979,4.844 2.198,5.042 1.219,0.198 10 false Confirmation Pulse 3.365,3.073 3.969,3.438 0.604,0.365 10 false Control Circuit 3.75,5.146 4.156,5.344 0.406,0.198 10 false GND 5.167,3.042 5.688,3.24 0.521,0.198 10 false INJ#1 5.156,4.083 5.635,4.281 0.479,0.198 10 false INJ#7 5.167,3.729 5.646,3.927 0.479,0.198 10 false INJ#6 5.167,3.385 5.635,3.583 0.469,0.198 10 false INJ#4 1.573,7.292 5.833,7.49 4.26,0.198 10 false CAUTION: Terminals I, H, K, L, M and N are high voltage terminals. 5.167,1.375 5.688,1.573 0.521,0.198 10 false COM2 5.167,2.198 5.688,2.396 0.521,0.198 10 false COM1 2.844,1.167 3.99,1.344 1.146,0.177 10 false DC/DC Converter 3.49,0.427 3.875,0.625 0.385,0.198 10 false EDU 5.49,2.531 6.01,2.729 0.521,0.198 10 false Injector

P062D
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Idling for 10 seconds Open or short in the No. 1 injector driver (EDU) or fuel injector circuit (1 trip detection logic).
·

Open or short in No. 1 injector driver (EDU) circuit

·

Fuel injector

·

No. 1 EDU

·

ECM



P062E
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Idling for 10 seconds Open or short in the No. 2 injector driver (EDU) or fuel injector circuit (1 trip detection logic).
·

Open or short in No. 2 injector driver (EDU) circuit

·

Fuel injector

·

No. 2 EDU

·

ECM



MONITOR DESCRIPTION

P062D, P062E (Open or short in EDU or fuel injector circuit):

The ECM continuously monitors both injection command (IJT) signals and injection confirmation (IJF) signals. This DTC will be stored if the ECM determines that the number of IJT signals and IJF signals are inconsistent.

The fuel injectors are grounded over a Field Effect Transistor (FET) and a serial resistor. This resistor creates a voltage drop, which is monitored by the EDU (injector drive circuit) in relation to the current drawn by the fuel injector. When the fuel injector current becomes too high, the voltage drop over the resistor exceeds a specified level and no IJF signal for that cylinder is sent to the ECM.

After the engine is started, when there is no injection confirmation (IJF) signal from the No. 1 or No. 2 EDU to the ECM even though the ECM sends injection command (IJT) signals to the No. 1 or No. 2 EDU, DTC P062D or DTC P062E is stored.

If this DTC is stored, the ECM enters fail-safe mode and limits engine power or stops the engine. The fail-safe mode continues until the ignition switch is turned off.

A145849E53
4.958,2.51 4.625,2.865 false 4.667,3.26 4.854,3.458 false 0.115,0.073 1.698,0.281 1.583,0.208 10 false Malfunction Detection: 2.604,0.656 3.01,0.854 0.406,0.198 10 false ECM 0.063,1.76 1.75,1.979 1.688,0.219 10 false Injection Command Signal 0.063,3.031 2.01,3.24 1.948,0.208 10 false Injection Confirmation Signal 2.156,1.969 2.448,2.177 0.292,0.208 10 false IJT 2.156,2.76 2.417,2.969 0.26,0.208 10 false IJF 3.302,1.781 3.583,1.979 0.281,0.198 10 false ON 3.615,0.469 5.156,0.708 1.542,0.24 10 false Command Signal (IJT) 3.594,1.146 5.281,1.344 1.688,0.198 10 false Confirmation Signal (IJF) 5.896,0.656 6.281,0.854 0.385,0.198 10 false EDU 3.708,2.146 4.073,2.344 0.365,0.198 10 false OFF 5.01,2.375 5.781,2.573 0.771,0.198 10 false Abnormal 4.906,3.385 5.49,3.583 0.583,0.198 10 false Normal


WIRING DIAGRAM

A182478E11
0.125,0.042 0.552,0.229 0.427,0.188 10 false No. 1: 0.625,0.771 0.969,0.938 0.344,0.167 10 false INJF 1.031,0.813 1.333,0.969 0.302,0.156 10 false C73 1.031,1.25 1.333,1.406 0.302,0.156 10 false C73 1.031,1.688 1.333,1.844 0.302,0.156 10 false C73 1.031,2.115 1.333,2.271 0.302,0.156 10 false C73 1.031,2.563 1.333,2.719 0.302,0.156 10 false C73 1.031,3.052 1.333,3.208 0.302,0.156 10 false C74 1.031,3.99 1.365,4.167 0.333,0.177 10 false C74 1.031,5.323 1.333,5.479 0.302,0.156 10 false C74 1.031,5.875 1.396,6.083 0.365,0.208 10 false C74 1.031,6.792 1.333,6.948 0.302,0.156 10 false C74 1.031,8.135 1.333,8.292 0.302,0.156 10 false C74 1.115,0.604 1.229,0.76 0.115,0.156 10 false 7 0.667,1.208 0.958,1.375 0.292,0.167 10 false #10 1.115,1.042 1.229,1.198 0.115,0.156 10 false 6 0.667,1.656 0.958,1.823 0.292,0.167 10 false #40 1.115,1.49 1.229,1.646 0.115,0.156 10 false 5 0.667,2.094 0.958,2.26 0.292,0.167 10 false #60 1.115,1.917 1.229,2.073 0.115,0.156 10 false 3 0.667,2.531 0.958,2.698 0.292,0.167 10 false #70 6.208,0.771 6.552,0.938 0.344,0.167 10 false INJF 6.208,1.208 6.5,1.375 0.292,0.167 10 false #1 6.208,1.656 6.5,1.823 0.292,0.167 10 false #4 6.208,2.094 6.5,2.26 0.292,0.167 10 false #6 6.208,2.542 6.5,2.708 0.292,0.167 10 false #7 5.854,0.802 6.177,1.01 0.323,0.208 10 false C46 5.521,0.802 5.844,1.031 0.323,0.229 10 false C45 5.833,0.604 6.177,0.76 0.344,0.156 10 false 61*2 5.5,0.604 5.823,0.76 0.323,0.156 10 false 61*1 5.865,1.24 6.177,1.427 0.313,0.188 10 false C46 5.521,1.24 5.844,1.417 0.323,0.177 10 false C45 5.833,1.042 6.177,1.198 0.344,0.156 10 false 40*2 5.5,1.042 5.823,1.198 0.323,0.156 10 false 40*1 5.865,1.677 6.198,1.885 0.333,0.208 10 false C46 5.521,1.688 5.844,1.885 0.323,0.198 10 false C45 5.833,1.49 6.177,1.646 0.344,0.156 10 false 37*2 5.5,1.49 5.823,1.646 0.323,0.156 10 false 37*1 5.865,2.115 6.188,2.292 0.323,0.177 10 false C46 5.521,2.115 5.844,2.281 0.323,0.167 10 false C45 5.833,1.917 6.177,2.073 0.344,0.156 10 false 35*2 5.5,1.917 5.823,2.073 0.323,0.156 10 false 35*1 5.865,2.552 6.208,2.729 0.344,0.177 10 false C46 5.521,2.563 5.833,2.771 0.313,0.208 10 false C45 5.833,2.365 6.177,2.521 0.344,0.156 10 false 34*2 5.5,2.365 5.823,2.521 0.323,0.156 10 false 34*1 1.115,2.365 1.229,2.521 0.115,0.156 10 false 2 0.646,3.031 0.969,3.198 0.323,0.167 10 false INJ1 1.115,2.865 1.229,3.021 0.115,0.156 10 false 4 3.625,3.135 3.74,3.292 0.115,0.156 10 false 2 4.25,3.135 4.365,3.292 0.115,0.156 10 false 1 2.271,2.792 2.469,2.958 0.198,0.167 10 false *3 2.271,4.198 2.469,4.365 0.198,0.167 10 false *3 2.271,5.646 2.469,5.813 0.198,0.167 10 false *3 2.271,6.99 2.469,7.156 0.198,0.167 10 false *3 0.646,5.292 0.969,5.458 0.323,0.167 10 false INJ4 1.115,5.135 1.229,5.292 0.115,0.156 10 false 3 0.646,5.865 0.969,6.031 0.323,0.167 10 false INJ6 1.115,5.708 1.229,5.865 0.115,0.156 10 false 2 0.646,8.135 0.969,8.302 0.323,0.167 10 false INJ7 1.115,7.969 1.229,8.125 0.115,0.156 10 false 1 0.531,3.958 0.958,4.125 0.427,0.167 10 false COM1 1.115,3.802 1.229,3.958 0.115,0.156 10 false 5 0.531,6.792 0.958,6.958 0.427,0.167 10 false COM2 1.115,6.625 1.229,6.781 0.115,0.156 10 false 6 3.427,3.344 3.688,3.521 0.26,0.177 10 false C5 3.427,3.49 4.635,3.656 1.208,0.167 10 false No. 1 Fuel Injector 3.427,4.688 3.76,4.865 0.333,0.177 10 false C14 3.427,4.833 4.635,5 1.208,0.167 10 false No. 4 Fuel Injector 3.427,6.146 3.76,6.323 0.333,0.177 10 false C69 3.427,6.292 4.635,6.458 1.208,0.167 10 false No. 6 Fuel Injector 3.427,7.531 3.76,7.708 0.333,0.177 10 false C68 3.427,7.677 4.635,7.844 1.208,0.167 10 false No. 7 Fuel Injector 4.26,4.5 4.375,4.656 0.115,0.156 10 false 2 3.625,4.5 3.74,4.656 0.115,0.156 10 false 1 3.625,5.979 3.74,6.135 0.115,0.156 10 false 2 4.25,5.979 4.365,6.135 0.115,0.156 10 false 1 4.26,7.323 4.375,7.479 0.115,0.156 10 false 2 3.625,7.323 3.74,7.479 0.115,0.156 10 false 1 5.26,8.479 6.052,8.635 0.792,0.156 10 false *3: Shielded 5.26,8.208 6.052,8.365 0.792,0.156 10 false *2: for RHD 5.26,7.938 6.052,8.094 0.792,0.156 10 false *1: for LHD 6.396,8.5 6.729,8.677 0.333,0.177 10 false ECM 0.052,8.458 1.781,8.667 1.729,0.208 10 false No. 1 Injector Driver (EDU)

A263486E02
0.802,0.646 1.01,0.823 0.208,0.177 10 false +B 1.063,0.677 1.427,0.875 0.365,0.198 10 false C74 1.156,0.479 1.385,0.656 0.229,0.177 10 false 8 0.677,1.354 1.01,1.531 0.333,0.177 10 false GND 1.073,1.375 1.396,1.583 0.323,0.208 10 false C73 1.156,1.177 1.385,1.354 0.229,0.177 10 false 1 0.156,4 1.865,4.188 1.708,0.188 10 false No. 1 Injector Driver (EDU) 2.531,3.948 3.021,4.115 0.49,0.167 10 false Battery 2.385,2.219 3.135,2.417 0.75,0.198 10 false EFI MAIN 3.042,3.135 4.125,3.281 1.083,0.146 10 false Integration Relay 3.427,2.781 3.771,2.958 0.344,0.177 10 false EFI 4.917,2.417 5.365,2.594 0.448,0.177 10 false EDU 1 5.698,0.385 6.01,0.583 0.313,0.198 10 false A38 6.406,0.354 6.802,0.51 0.396,0.156 10 false BATT 4.76,1.344 4.885,1.5 0.125,0.156 10 false 3 5.469,1.344 5.594,1.5 0.125,0.156 10 false 5 4.76,1.969 4.885,2.125 0.125,0.156 10 false 1 5.469,1.969 5.594,2.125 0.125,0.156 10 false 2 5.667,0.208 6,0.365 0.333,0.156 10 false 20*1 5.698,2.083 6.01,2.24 0.313,0.156 10 false A38 6.406,2.063 6.781,2.219 0.375,0.156 10 false IREL 5.698,1.896 6.052,2.052 0.354,0.156 10 false 45*1 5.698,3.271 5.99,3.438 0.292,0.167 10 false A38 6.406,3.25 6.854,3.406 0.448,0.156 10 false MREL 6.479,3.906 6.958,4.094 0.479,0.188 10 false ECM 5.677,3.083 6.031,3.24 0.354,0.156 10 false 44*1 5.094,3.958 5.865,4.146 0.771,0.188 10 false *1: for LHD 5.094,4.271 5.865,4.458 0.771,0.188 10 false *2: for RHD 5.698,2.688 5.99,2.844 0.292,0.156 10 false A38 6.406,2.667 6.667,2.823 0.26,0.156 10 false +B 5.74,2.5 5.979,2.656 0.24,0.156 10 false 2*1 6.042,0.396 6.354,0.583 0.313,0.188 10 false A52 6.021,0.208 6.354,0.365 0.333,0.156 10 true 20*2 6.063,2.094 6.385,2.281 0.323,0.188 10 false A52 6.021,1.896 6.375,2.052 0.354,0.156 10 false 45*2 6.052,3.271 6.385,3.469 0.333,0.198 10 false A52 6.021,3.083 6.375,3.24 0.354,0.156 10 false 44*2 6.052,2.688 6.344,2.875 0.292,0.188 10 false A52 6.083,2.5 6.323,2.656 0.24,0.156 10 false 2*2 2.719,1.563 2.844,1.719 0.125,0.156 10 false 1 2.063,1.896 2.188,2.052 0.125,0.156 10 false 1 2.917,1.594 3.188,1.781 0.271,0.188 10 false 1B 2.25,2.906 2.375,3.063 0.125,0.156 10 false 3 2.438,2.938 2.729,3.125 0.292,0.188 10 false 1B 2.021,2.094 2.302,2.344 0.281,0.25 10 false 1C 4.083,1.896 4.208,2.052 0.125,0.156 10 false 4 4.031,2.094 4.271,2.26 0.24,0.167 10 false 1B 4.083,2.292 4.208,2.448 0.125,0.156 10 false 2 4.031,2.479 4.271,2.667 0.24,0.188 10 false 1B

A182478E12
0.125,0.031 0.552,0.219 0.427,0.188 10 false No. 2: 0.625,0.76 0.969,0.927 0.344,0.167 10 false INF2 1.031,0.802 1.375,0.979 0.344,0.177 10 false C75 1.031,1.24 1.375,1.417 0.344,0.177 10 false C75 1.031,1.677 1.354,1.885 0.323,0.208 10 false C75 1.031,2.104 1.375,2.302 0.344,0.198 10 false C75 1.031,2.552 1.396,2.771 0.365,0.219 10 false C75 1.031,3.052 1.365,3.25 0.333,0.198 10 false C76 1.031,3.979 1.365,4.135 0.333,0.156 10 false C76 1.031,5.313 1.344,5.479 0.313,0.167 10 false C76 1.031,5.865 1.333,6.021 0.302,0.156 10 false C76 1.031,6.802 1.333,6.958 0.302,0.156 10 false C76 1.031,8.135 1.375,8.313 0.344,0.177 10 false C76 1.115,0.594 1.229,0.75 0.115,0.156 10 false 7 0.667,1.198 0.958,1.365 0.292,0.167 10 false #20 1.115,1.021 1.229,1.177 0.115,0.156 10 false 6 0.667,1.646 0.958,1.813 0.292,0.167 10 false #30 1.115,1.469 1.229,1.625 0.115,0.156 10 false 2 0.667,2.073 0.958,2.24 0.292,0.167 10 false #50 1.115,1.906 1.229,2.063 0.115,0.156 10 false 5 0.667,2.521 0.958,2.688 0.292,0.167 10 false #80 6.208,0.76 6.552,0.927 0.344,0.167 10 false INF2 6.208,1.198 6.5,1.365 0.292,0.167 10 false #2 6.219,1.646 6.51,1.813 0.292,0.167 10 false #3 6.208,2.073 6.5,2.24 0.292,0.167 10 false #5 6.208,2.521 6.5,2.688 0.292,0.167 10 false #8 5.854,0.792 6.188,1 0.333,0.208 10 false C46 5.521,0.802 5.833,0.979 0.313,0.177 10 false C45 5.833,0.583 6.177,0.74 0.344,0.156 10 false 60*2 5.5,0.583 5.823,0.74 0.323,0.156 10 false 60*1 5.854,1.25 6.219,1.469 0.365,0.219 10 false C46 5.521,1.24 5.833,1.427 0.313,0.188 10 false C45 5.833,1.031 6.177,1.188 0.344,0.156 10 false 39*2 5.5,1.031 5.823,1.188 0.323,0.156 10 false 39*1 5.865,1.677 6.188,1.844 0.323,0.167 10 false C46 5.521,1.677 5.833,1.854 0.313,0.177 10 false C45 5.833,1.469 6.177,1.625 0.344,0.156 10 false 38*2 5.5,1.469 5.823,1.625 0.323,0.156 10 false 38*1 5.854,2.115 6.177,2.281 0.323,0.167 10 false C46 5.521,2.115 5.833,2.302 0.313,0.188 10 false C45 5.833,1.906 6.177,2.063 0.344,0.156 10 false 36*2 5.5,1.906 5.823,2.063 0.323,0.156 10 false 36*1 5.844,2.552 6.177,2.719 0.333,0.167 10 false C46 5.51,2.552 5.823,2.719 0.313,0.167 10 false C45 5.833,2.354 6.177,2.51 0.344,0.156 10 false 33*2 5.5,2.354 5.823,2.51 0.323,0.156 10 false 33*1 1.115,2.344 1.229,2.5 0.115,0.156 10 false 3 0.646,3.01 0.969,3.177 0.323,0.167 10 false INJ2 1.115,2.844 1.229,3 0.115,0.156 10 false 4 3.604,3.125 3.719,3.281 0.115,0.156 10 false 2 4.25,3.125 4.365,3.281 0.115,0.156 10 false 1 2.271,2.771 2.469,2.938 0.198,0.167 10 false *3 2.271,4.177 2.469,4.344 0.198,0.167 10 false *3 2.271,5.635 2.469,5.802 0.198,0.167 10 false *3 2.271,6.969 2.469,7.135 0.198,0.167 10 false *3 0.646,5.281 0.969,5.448 0.323,0.167 10 false INJ5 1.115,5.125 1.229,5.281 0.115,0.156 10 false 3 0.646,5.844 0.969,6.01 0.323,0.167 10 false INJ3 1.115,5.688 1.229,5.844 0.115,0.156 10 false 1 0.646,8.125 0.969,8.292 0.323,0.167 10 false INJ8 1.115,7.948 1.229,8.104 0.115,0.156 10 false 2 0.531,3.948 0.958,4.115 0.427,0.167 10 false COM4 1.115,3.781 1.229,3.938 0.115,0.156 10 false 5 0.531,6.771 0.958,6.938 0.427,0.167 10 false COM5 1.115,6.615 1.229,6.771 0.115,0.156 10 false 6 3.427,3.323 3.813,3.5 0.385,0.177 10 false C70 3.427,3.469 4.635,3.635 1.208,0.167 10 false No. 2 Fuel Injector 3.427,4.667 3.76,4.844 0.333,0.177 10 false C9 3.427,4.813 4.635,4.979 1.208,0.167 10 false No. 5 Fuel Injector 3.427,6.135 3.76,6.313 0.333,0.177 10 false C67 3.427,6.281 4.635,6.448 1.208,0.167 10 false No. 3 Fuel Injector 3.427,7.51 3.76,7.688 0.333,0.177 10 false C54 3.427,7.656 4.635,7.823 1.208,0.167 10 false No. 8 Fuel Injector 4.26,4.49 4.375,4.646 0.115,0.156 10 false 2 3.625,4.49 3.74,4.646 0.115,0.156 10 false 1 3.625,5.969 3.74,6.125 0.115,0.156 10 false 2 4.25,5.969 4.365,6.125 0.115,0.156 10 false 1 4.26,7.302 4.375,7.458 0.115,0.156 10 false 2 3.625,7.302 3.74,7.458 0.115,0.156 10 false 1 5.26,8.469 6.052,8.625 0.792,0.156 10 false *3: Shielded 5.26,8.188 6.052,8.344 0.792,0.156 10 false *2: for RHD 5.26,7.917 6.052,8.073 0.792,0.156 10 false *1: for LHD 6.375,8.448 6.708,8.625 0.333,0.177 10 false ECM 0.042,8.458 1.781,8.677 1.74,0.219 10 false No. 2 Injector Driver (EDU)

A275256E04
0.75,0.656 1.021,0.854 0.271,0.198 10 false +B 1.094,0.688 1.521,0.865 0.427,0.177 10 false C76 1.146,0.469 1.375,0.646 0.229,0.177 10 false 8 0.646,1.375 1.021,1.573 0.375,0.198 10 false GND 1.146,1.177 1.375,1.354 0.229,0.177 10 false 1 0.156,3.979 1.865,4.167 1.708,0.188 10 false No. 2 Injector Driver (EDU) 2.521,3.948 3.01,4.115 0.49,0.167 10 false Battery 2.344,2.24 3.125,2.427 0.781,0.188 10 false EFI MAIN 2 3.042,3.125 4.219,3.365 1.177,0.24 10 false Integration Relay 4.938,2.417 5.5,2.656 0.563,0.24 10 false EDU 2 4.75,1.333 4.875,1.49 0.125,0.156 10 false 3 5.458,1.333 5.583,1.49 0.125,0.156 10 false 5 4.75,1.958 4.875,2.115 0.125,0.156 10 false 1 5.458,1.958 5.583,2.115 0.125,0.156 10 false 2 5.708,2.083 6.073,2.323 0.365,0.24 10 false A38 6.396,2.052 6.771,2.208 0.375,0.156 10 false IRL2 5.688,1.885 6.042,2.042 0.354,0.156 10 false 46*1 5.708,3.271 6.021,3.458 0.313,0.188 10 false A38 6.396,3.25 6.844,3.406 0.448,0.156 10 false MREL 6.469,3.906 6.927,4.135 0.458,0.229 10 false ECM 5.677,3.083 6.031,3.24 0.354,0.156 10 false 44*1 5.083,3.948 5.854,4.135 0.771,0.188 10 false *1: for LHD 5.083,4.271 5.854,4.458 0.771,0.188 10 false *2: for RHD 6.052,2.083 6.385,2.271 0.333,0.188 10 false A52 6.031,1.885 6.385,2.042 0.354,0.156 10 false 46*2 6.052,3.281 6.365,3.458 0.313,0.177 10 false A52 6.021,3.083 6.375,3.24 0.354,0.156 10 false 44*2 2.052,1.896 2.177,2.052 0.125,0.156 10 false 1 2.25,2.896 2.375,3.052 0.125,0.156 10 false 3 2.438,2.927 2.719,3.135 0.281,0.208 10 false 1A 2.01,2.094 2.302,2.271 0.292,0.177 10 false 1C 4.083,1.896 4.208,2.052 0.125,0.156 10 false 4 4.031,2.094 4.292,2.281 0.26,0.188 10 false 1A 4.083,2.281 4.208,2.438 0.125,0.156 10 false 2 4.031,2.479 4.323,2.656 0.292,0.177 10 false 1A 1.094,1.385 1.521,1.563 0.427,0.177 10 false C75 3.177,2.802 3.948,2.948 0.771,0.146 10 false EFI MAIN 2

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing a fuel injector, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE EDU POWER SOURCE
a.

Disconnect the No. 1 injector driver (EDU) connectors.


b.
U162834E01
0.312,0.87 0.587,1.039 0.275,0.169 10 C73 0.682,0.758 0.861,0.902 0.180,0.144 10 *1 0.317,1.175 0.606,1.344 0.289,0.169 10 C75 0.682,1.064 0.861,1.208 0.180,0.144 10 *2 0.312,2.678 0.587,2.847 0.275,0.169 10 C74 0.682,2.566 0.861,2.710 0.180,0.144 10 *1 0.229,3.962 0.848,4.140 0.619,0.178 10 *1: No. 1 0.229,4.28 0.848,4.458 0.619,0.178 10 *2: No. 2 0.317,2.983 0.606,3.152 0.289,0.169 10 C76 0.682,2.872 0.861,3.016 0.180,0.144 10 *2 0.671,1.783 1.046,2.016 0.375,0.233 10 GND 2.444,3.742 2.819,3.975 0.375,0.233 10 +B 0.199,0.016 2.582,0.373 2.384,0.358 10 Front view of wire harness connector: (to EDU) 1.082,1.5 0.891,1.753 false 2.331,3.445 2.522,3.723 false

Disconnect the No. 2 injector driver (EDU) connectors.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
No. 1
Tester Connection Switch Condition Specified Condition
C74-8 (+B) - C73-1 (GND) Ignition switch ON 11 to 14 V

No. 2
Tester Connection Switch Condition Specified Condition
C76-8 (+B) - C75-1 (GND) Ignition switch ON 11 to 14 V




OK

2.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - EDU)

NG

7.GO TO INJECTOR CIRCUIT
2.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - EDU)
A385207E01
1.146,0.875 1.521,1.104 0.375,0.229 1.75,0.885 2.125,1.115 0.375,0.229 2.344,0.885 2.719,1.115 0.375,0.229 2.927,0.885 3.302,1.115 0.375,0.229 4.917,0.917 5.333,1.156 0.417,0.24 4.281,2.052 4.552,1.802 true 4.542,2.094 4.677,1.802 true 4.802,2.104 4.844,1.823 true 5.177,2.115 5.021,1.802 true 5.49,2.104 5.177,1.802 true 5.948,2.104 5.333,1.802 true 0.802,0.115 3.115,0.51 2.313,0.396 10 false Front view of wire harness connector: (to Fuel injector) 1.24,0.906 1.552,1.104 0.313,0.198 10 false C5 1.823,0.917 2.135,1.115 0.313,0.198 10 false C14 2.417,0.917 2.729,1.115 0.313,0.198 10 false C69 2.99,0.917 3.302,1.115 0.313,0.198 10 false C68 1.552,0.844 1.781,1.031 0.229,0.188 10 false *1 2.167,0.833 2.396,1.021 0.229,0.188 10 false *2 2.76,0.854 2.99,1.042 0.229,0.188 10 false *3 3.344,0.833 3.573,1.021 0.229,0.188 10 false *4 4.01,0.125 6.323,0.521 2.313,0.396 10 false Front view of wire harness connector: (to No. 1 EDU) 4.99,0.958 5.302,1.156 0.313,0.198 10 false C74 3.948,2 4.323,2.177 0.375,0.177 10 false INJ7 4.323,2.125 4.698,2.302 0.375,0.177 10 false INJ6 4.688,2.135 5.063,2.313 0.375,0.177 10 false INJ4 5.073,2.146 5.448,2.323 0.375,0.177 10 false INJ1 5.438,2.125 5.896,2.313 0.458,0.188 10 false COM1 5.99,2.073 6.469,2.26 0.479,0.188 10 false COM2 0.125,1.5 1.573,1.677 1.448,0.177 10 false *1: No. 1 Fuel Injector 0.125,1.781 1.573,1.958 1.448,0.177 10 false *2: No. 4 Fuel Injector 0.115,2.094 1.563,2.271 1.448,0.177 10 false *3: No. 6 Fuel Injector 0.125,2.417 1.573,2.594 1.448,0.177 10 false *4: No. 7 Fuel Injector

a.

Disconnect the fuel injector connectors.


b.

Disconnect the No. 1 EDU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
No. 1
Tester Connection Condition Specified Condition
C5-2 - C74-4 (INJ1) Always Below 1 Ω
C14-2 - C74-3 (INJ4) Always Below 1 Ω
C69-2 - C74-2 (INJ6) Always Below 1 Ω
C68-2 - C74-1 (INJ7) Always Below 1 Ω
C5-1 - C74-5 (COM1) Always Below 1 Ω
C14-1 - C74-5 (COM1) Always Below 1 Ω
C69-1 - C74-6 (COM2) Always Below 1 Ω
C68-1 - C74-6 (COM2) Always Below 1 Ω


Standard Resistance (Check for Short):
No. 1
Tester Connection Condition Specified Condition
C5-2 or C74-4 (INJ1) - Body ground Always 10 kΩ or higher
C14-2 or C74-3 (INJ4) - Body ground Always 10 kΩ or higher
C69-2 or C74-2 (INJ6) - Body ground Always 10 kΩ or higher
C68-2 or C74-1 (INJ7) - Body ground Always 10 kΩ or higher
C5-1 or C74-5 (COM1) - Body ground Always 10 kΩ or higher
C14-1 or C74-5 (COM1) - Body ground Always 10 kΩ or higher
C69-1 or C74-6 (COM2) - Body ground Always 10 kΩ or higher
C68-1 or C74-6 (COM2) - Body ground Always 10 kΩ or higher



A385207E02
1.146,0.875 1.521,1.104 0.375,0.229 1.75,0.885 2.125,1.115 0.375,0.229 2.344,0.885 2.719,1.115 0.375,0.229 2.927,0.885 3.302,1.115 0.375,0.229 4.917,0.917 5.333,1.156 0.417,0.24 4.281,2.052 4.552,1.802 true 4.542,2.094 4.677,1.802 true 4.802,2.104 4.844,1.823 true 5.177,2.115 5.021,1.802 true 5.49,2.104 5.177,1.802 true 5.948,2.104 5.333,1.802 true 0.802,0.115 3.115,0.51 2.313,0.396 10 false Front view of wire harness connector: (to Fuel injector) 1.198,0.906 1.51,1.104 0.313,0.198 10 false C70 1.823,0.917 2.135,1.115 0.313,0.198 10 false C67 2.438,0.917 2.75,1.115 0.313,0.198 10 false C9 2.99,0.917 3.302,1.115 0.313,0.198 10 false C54 1.552,0.844 1.781,1.031 0.229,0.188 10 false *1 2.167,0.833 2.396,1.021 0.229,0.188 10 false *2 2.76,0.854 2.99,1.042 0.229,0.188 10 false *3 3.344,0.833 3.573,1.021 0.229,0.188 10 false *4 4.01,0.115 6.323,0.51 2.313,0.396 10 false Front view of wire harness connector: (to No. 2 EDU) 4.99,0.958 5.302,1.156 0.313,0.198 10 false C76 3.948,2 4.323,2.177 0.375,0.177 10 false INJ3 4.323,2.125 4.698,2.302 0.375,0.177 10 false INJ8 4.688,2.135 5.063,2.313 0.375,0.177 10 false INJ5 5.073,2.146 5.448,2.323 0.375,0.177 10 false INJ2 5.438,2.125 5.917,2.313 0.479,0.188 10 false COM4 5.99,2.073 6.469,2.26 0.479,0.188 10 false COM5 0.125,1.5 1.573,1.677 1.448,0.177 10 false *1: No. 2 Fuel Injector 0.125,1.781 1.573,1.958 1.448,0.177 10 false *2: No. 3 Fuel Injector 0.115,2.094 1.563,2.271 1.448,0.177 10 false *3: No. 5 Fuel Injector 0.125,2.417 1.573,2.594 1.448,0.177 10 false *4: No. 8 Fuel Injector

d.

Disconnect the fuel injector connectors.


e.

Disconnect the No. 2 EDU connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
No. 2
Tester Connection Condition Specified Condition
C70-2 - C76-4 (INJ2) Always Below 1 Ω
C9-2 - C76-3 (INJ5) Always Below 1 Ω
C67-2 - C76-1 (INJ3) Always Below 1 Ω
C54-2 - C76-2 (INJ8) Always Below 1 Ω
C70-1 - C76-5 (COM4) Always Below 1 Ω
C9-1 - C76-5 (COM4) Always Below 1 Ω
C67-1 - C76-6 (COM5) Always Below 1 Ω
C54-1 - C76-6 (COM5) Always Below 1 Ω


Standard Resistance (Check for Short):
No. 2
Tester Connection Condition Specified Condition
C70-2 or C76-4 (INJ2) - Body ground Always 10 kΩ or higher
C9-2 or C76-3 (INJ5) - Body ground Always 10 kΩ or higher
C67-2 or C76-1 (INJ3) - Body ground Always 10 kΩ or higher
C54-2 or C76-2 (INJ8) - Body ground Always 10 kΩ or higher
C70-1 or C76-5 (COM4) - Body ground Always 10 kΩ or higher
C9-1 or C76-5 (COM4) - Body ground Always 10 kΩ or higher
C67-1 or C76-6 (COM5) - Body ground Always 10 kΩ or higher
C54-1 or C76-6 (COM5) - Body ground Always 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (EDU - ECM)

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (EDU - ECM)
a.

Disconnect the No. 1 EDU connector.

A385209E01
1.74,0.854 2.177,1.104 0.438,0.25 4.167,0.823 4.604,1.073 0.438,0.25 5.031,0.813 5.469,1.063 0.438,0.25 1.396,2.01 1.625,1.729 true 1.677,2.021 1.792,1.719 true 2.021,2.021 2.083,1.719 true 2.323,1.99 2.229,1.719 true 2.646,2 2.417,1.74 true 5.833,2.167 5.156,1.479 true 5.302,2.313 5.021,1.552 true 4.844,2.208 4.948,1.49 true 4.448,2.354 4.792,1.49 true 4.135,2.198 4.719,1.49 true 0.76,0.208 3.073,0.563 2.313,0.354 10 false Front view of wire harness connector: (to No. 1 EDU) 3.865,0.156 6.177,0.51 2.313,0.354 10 false Front view of wire harness connector: (to ECM) 1.198,2.031 1.552,2.208 0.354,0.177 10 false #70 1.531,2.031 1.885,2.208 0.354,0.177 10 false #60 1.865,2.031 2.219,2.208 0.354,0.177 10 false #40 2.177,2.031 2.531,2.208 0.354,0.177 10 false #10 2.552,2.021 2.906,2.198 0.354,0.177 10 false INJF 1.823,0.906 2.177,1.083 0.354,0.177 10 false C73 4.26,0.875 4.615,1.052 0.354,0.177 10 false C45 5.115,0.865 5.469,1.042 0.354,0.177 10 false C46 4.635,0.76 4.885,0.958 0.25,0.198 10 false *1 5.51,0.76 5.76,0.958 0.25,0.198 10 false *2 3.802,2.219 4.302,2.438 0.5,0.219 10 false 34 (#7) 4.198,2.396 4.698,2.615 0.5,0.219 10 false 35 (#6) 4.708,2.24 5.208,2.458 0.5,0.219 10 false 37 (#4) 5.719,2.188 6.302,2.385 0.583,0.198 10 false 40 (#1) 5.167,2.344 5.833,2.573 0.667,0.229 10 false 61 (INJF) 0.25,2.042 1.031,2.25 0.781,0.208 10 false *1: for LHD 0.25,2.354 1.031,2.563 0.781,0.208 10 false *2: for RHD


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
No. 1 (for LHD)
Tester Connection Condition Specified Condition
C73-6 (#10) - C45-40 (#1) Always Below 1 Ω
C73-5 (#40) - C45-37 (#4) Always Below 1 Ω
C73-3 (#60) - C45-35 (#6) Always Below 1 Ω
C73-2 (#70) - C45-34 (#7) Always Below 1 Ω
C73-7 (INJF) - C45-61 (INJF) Always Below 1 Ω

No. 1 (for RHD)
Tester Connection Condition Specified Condition
C73-6 (#10) - C46-40 (#1) Always Below 1 Ω
C73-5 (#40) - C46-37 (#4) Always Below 1 Ω
C73-3 (#60) - C46-35 (#6) Always Below 1 Ω
C73-2 (#70) - C46-34 (#7) Always Below 1 Ω
C73-7 (INJF) - C46-61 (INJF) Always Below 1 Ω


Standard Resistance (Check for Short):
No. 1 (for LHD)
Tester Connection Condition Specified Condition
C73-6 (#10) or C45-40 (#1) - Body ground Always 10 kΩ or higher
C73-5 (#40) or C45-37 (#4) - Body ground Always 10 kΩ or higher
C73-3 (#60) or C45-35 (#6) - Body ground Always 10 kΩ or higher
C73-2 (#70) or C45-34 (#7) - Body ground Always 10 kΩ or higher
C73-7 (INJF) or C45-61 (INJF) - Body ground Always 10 kΩ or higher

No. 1 (for RHD)
Tester Connection Condition Specified Condition
C73-6 (#10) or C46-40 (#1) - Body ground Always 10 kΩ or higher
C73-5 (#40) or C46-37 (#4) - Body ground Always 10 kΩ or higher
C73-3 (#60) or C46-35 (#6) - Body ground Always 10 kΩ or higher
C73-2 (#70) or C46-34 (#7) - Body ground Always 10 kΩ or higher
C73-7 (INJF) or C46-61 (INJF) - Body ground Always 10 kΩ or higher



d.

Disconnect the No. 2 EDU connector.

A385209E02
1.74,0.854 2.177,1.104 0.438,0.25 4.167,0.823 4.604,1.073 0.438,0.25 5.031,0.813 5.469,1.063 0.438,0.25 1.396,2.01 1.625,1.729 true 1.677,2.021 1.792,1.719 true 2.021,2.021 2.083,1.719 true 2.323,1.99 2.229,1.719 true 2.646,2 2.417,1.74 true 5.75,2.167 5.073,1.479 true 5.49,2.354 5.021,1.479 true 4.844,2.208 4.938,1.542 true 4.521,2.354 4.865,1.49 true 4.073,2.198 4.656,1.49 true 0.76,0.167 3.073,0.521 2.313,0.354 10 false Front view of wire harness connector: (to No. 2 EDU) 3.865,0.156 6.177,0.51 2.313,0.354 10 false Front view of wire harness connector: (to ECM) 1.198,2.031 1.552,2.208 0.354,0.177 10 false #30 1.531,2.031 1.885,2.208 0.354,0.177 10 false #80 1.865,2.031 2.219,2.208 0.354,0.177 10 false #50 2.177,2.031 2.531,2.208 0.354,0.177 10 false #20 2.552,2.021 2.906,2.198 0.354,0.177 10 false INF2 1.823,0.906 2.177,1.083 0.354,0.177 10 false C75 4.26,0.875 4.615,1.052 0.354,0.177 10 false C45 5.115,0.865 5.469,1.042 0.354,0.177 10 false C46 4.635,0.76 4.885,0.958 0.25,0.198 10 false *1 5.51,0.76 5.76,0.958 0.25,0.198 10 false *2 3.802,2.219 4.302,2.438 0.5,0.219 10 false 33 (#8) 4.198,2.396 4.698,2.615 0.5,0.219 10 false 36 (#5) 4.708,2.229 5.323,2.417 0.615,0.188 10 false 60 (INJ2) 5.719,2.188 6.302,2.385 0.583,0.198 10 false 39 (#2) 5.302,2.354 5.969,2.583 0.667,0.229 10 false 38 (#3) 0.25,2.042 1.031,2.25 0.781,0.208 10 false *1: for LHD 0.25,2.354 1.031,2.563 0.781,0.208 10 false *2: for RHD


e.

Disconnect the ECM connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
No. 2 (for LHD)
Tester Connection Condition Specified Condition
C75-6 (#20) - C45-39 (#2) Always Below 1 Ω
C75-2 (#30) - C45-38 (#3) Always Below 1 Ω
C75-5 (#50) - C45-36 (#5) Always Below 1 Ω
C75-3 (#80) - C45-33 (#8) Always Below 1 Ω
C75-7 (INF2) - C45-60 (INF2) Always Below 1 Ω

No. 2 (for RHD)
Tester Connection Condition Specified Condition
C75-6 (#20) - C46-39 (#2) Always Below 1 Ω
C75-2 (#30) - C46-38 (#3) Always Below 1 Ω
C75-5 (#50) - C46-36 (#5) Always Below 1 Ω
C75-3 (#80) - C46-33 (#8) Always Below 1 Ω
C75-7 (INF2) - C46-60 (INF2) Always Below 1 Ω


Standard Resistance (Check for Short):
No. 2 (for LHD)
Tester Connection Condition Specified Condition
C75-6 (#20) or C45-39 (#2) - Body ground Always 10 kΩ or higher
C75-2 (#30) or C45-38 (#3) - Body ground Always 10 kΩ or higher
C75-5 (#50) or C45-36 (#5) - Body ground Always 10 kΩ or higher
C75-3 (#80) or C45-33 (#8) - Body ground Always 10 kΩ or higher
C75-7 (INF2) or C45-60 (INF2) - Body ground Always 10 kΩ or higher

No. 2 (for RHD)
Tester Connection Condition Specified Condition
C75-6 (#20) or C46-39 (#2) - Body ground Always 10 kΩ or higher
C75-2 (#30) or C46-38 (#3) - Body ground Always 10 kΩ or higher
C75-5 (#50) or C46-36 (#5) - Body ground Always 10 kΩ or higher
C75-3 (#80) or C46-33 (#8) - Body ground Always 10 kΩ or higher
C75-7 (INF2) or C46-60 (INF2) - Body ground Always 10 kΩ or higher




OK

4.INSPECT FUEL INJECTOR (RESISTANCE)

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.INSPECT FUEL INJECTOR (RESISTANCE)
a.
A165911E02
0.2,0 2.727,0.375 2.527,0.375 10 Component without harness connected: (Fuel injector)

Disconnect the fuel injector connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 0.85 to 1.05 Ω




OK

5.INSPECT INJECTOR DRIVER (No. 1 and No. 2)

NG

9.REPLACE FUEL INJECTOR
5.INSPECT INJECTOR DRIVER (No. 1 and No. 2)
a.
A176216

Interchange the No. 1 and No. 2 EDU connectors.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON and turn the tester on.


d.

Clear the DTCs (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DTC CHECK / CLEAR).

NOTICE:

Before clearing the DTCs, write them down.



e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine / DTC.


g.

Read the DTCs.

Result
Result Proceed to
DTCs do not change A
DTCs change (change in malfunctioning cylinder or EDU code) B



A

6.REPLACE ECM

B

8.REPLACE INJECTOR DRIVER (No. 1 or No. 2)
6.REPLACE ECM

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.GO TO INJECTOR CIRCUIT

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPLACE INJECTOR DRIVER (No. 1 or No. 2)
a.

Replace the injector driver (No. 1 or No. 2) (See page Engine / Hybrid System>1VD-FTV (FUEL)>INJECTOR DRIVER>REMOVAL).



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPLACE FUEL INJECTOR

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Start the engine and idle it for 10 seconds.


e.

Enter the following menus: Powertrain / Engine / DTC.


f.

Confirm that the DTC is not output again.



NEXT

END