Home › Engine / Hybrid System › 1VD-FTV (FUEL) › FUEL INJECTOR (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052783 1VD-FTV FUEL _0255109 FUEL INJECTOR(w/o DPF) A

1VD-FTV FUEL  FUEL INJECTOR(w/o DPF)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

When replacing an injector (including interchanging injectors between cylinders) or common rail, replace the corresponding injection pipes with new ones.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


a.

Disconnect the cables from the negative (-) main battery and sub-battery terminals.


Hide 53806 3.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Hide 53805 4.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Hide 51405A 5.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 53292A 6.REMOVE UPPER RADIATOR SUPPORT SEAL

Hide 17940D 8.REMOVE INTERCOOLER ASSEMBLY (w/ Intercooler)

Hide 17973 9.REMOVE NO. 1 COOL AIR INLET (w/o Intercooler)

Hide 17973 10.REMOVE NO. 2 COOL AIR INLET (w/o Intercooler)

Hide 12.REMOVE NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 15.DRAIN CLUTCH FLUID (for Manual Transmission)

Hide 31418 16.REMOVE CLUTCH HOSE (for Manual Transmission)

Hide 31489 18.REMOVE TUBE CONNECTOR TO FLEXIBLE HOSE TUBE (for Manual Transmission)

Hide 17947B 20.REMOVE NO. 3 INTERCOOLER SUPPORT BRACKET

Hide 26100G 21.REMOVE DIESEL THROTTLE BODY ASSEMBLY LH

Hide 17806 28.REMOVE NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY

Hide 87208 29.REMOVE HEATER WATER PIPE SUB-ASSEMBLY (w/ Viscous Heater)

Hide 17885 30.REMOVE NO. 1 AIR CLEANER PIPE SUB-ASSEMBLY

Hide 16268M 32.REMOVE NO. 3 WATER BY-PASS PIPE (w/o Viscous Heater)

Hide 23706 36.REMOVE NO. 6 INJECTION PIPE SUB-ASSEMBLY

Hide 23820A 38.REMOVE COMMON RAIL ASSEMBLY LH

Hide 23801L 39.REMOVE FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY

Hide 25860 42.REMOVE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (for Engine Mounting)

a.
A174969

Disconnect the 2 vacuum hoses.


b.

Remove the bolt and vacuum switching valve.


Hide 25706 43.REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

a.
A264755

w/ Intercooler:

Disconnect the 2 vacuum hoses.


b.
A264102

Remove the 3 bolts and vacuum transmitting pipe.


Hide 11225 45.REMOVE CYLINDER HEAD COVER SILENCER LH (w/ Intercooler)

a.
A174975

Remove the 3 bolts and cylinder head cover silencer.


Hide 23681C 46.REMOVE NOZZLE HOLDER SEAL LH

a.
A164170

Using a small screwdriver, remove the 4 holder seals by prying the portion between each holder seal and the cutout part of the cylinder head cover.

HINT:

Tape the screwdriver tip before use.



Hide 12270 47.REMOVE OIL SEPARATOR ASSEMBLY

a.
A164169

Remove the 3 bolts, oil separator and gasket.


Hide 11202 48.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

a.
A164162

Remove the 17 bolts, cylinder head cover and gasket.


Hide 11229 49.REMOVE NOZZLE HOLDER GASKET LH

a.
A174977

Using a small screwdriver and hammer, remove the 4 nozzle holder gaskets.

HINT:

Tape the screwdriver tip before use.



Hide 11224 51.REMOVE CYLINDER HEAD COVER SILENCER RH (w/ Intercooler)

a.
A174974

Remove the 3 bolts and cylinder head cover silencer.


Hide 23681C 52.REMOVE NOZZLE HOLDER SEAL RH

a.
A164171

Using a small screwdriver, remove the 4 holder seals by prying the portion between each holder seal and the cutout part of the cylinder head cover.

HINT:

Tape the screwdriver tip before use.



Hide 11201 53.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH

a.
A174971

Remove the 18 bolts, cylinder head cover and gasket.


Hide 11229 54.REMOVE NOZZLE HOLDER GASKET RH

a.
A174977

Using a small screwdriver and hammer, remove the 4 nozzle holder gaskets.

HINT:

Tape the screwdriver tip before use.



Hide 55.REMOVE FUEL INJECTOR RH

a.
A176409

Remove the union bolt, 4 hollow screws, 5 gaskets and nozzle leakage pipe.

Text in Illustration
V100136

Union Bolt

NOTICE:
·

When removing the nozzle leakage pipe, place a cushion under the pipe.

·

Be careful not to deform or scratch the union seal surface.

·

After removing the nozzle leakage pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.




b.
A164166

Remove the 4 bolts, 4 washers, 4 nozzle holder clamps and 4 injectors.

HINT:

Arrange the injectors, holder clamps, washers and bolts in the correct order.



c.

Remove the O-ring from each injector.


d.

Remove the 4 injection nozzle seats from the cylinder head.


Hide 56.REMOVE FUEL INJECTOR LH

a.
A176410

Remove the union bolt, 4 hollow screws, 5 gaskets and No. 2 nozzle leakage pipe.

Text in Illustration
V100136

Union Bolt

NOTICE:
·

When removing the nozzle leakage pipe, place a cushion under the pipe.

·

Be careful not to deform or scratch the union seal surface.

·

After removing the nozzle leakage pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.




b.
A164165

Remove the 4 bolts, 4 washers, 4 nozzle holder clamps and 4 injectors.

HINT:

Arrange the injectors, holder clamps, washers and bolts in the correct order.



c.

Remove the O-ring from each injector.


d.

Remove the 4 injection nozzle seats from the cylinder head.