Faults and Symptoms of Common Rail Diesel Components
Engine Control
| Main fault | Decrease in performance (foreign matter is stuck) |
| Symptoms | Lack of power, black smoke |
| Data List | MAF |
|
|
| Symptom and Corresponding Main Fault | ·
Lack of power (no black smoke) due to air filter blockage or crushed or leaking air duct ·
Black smoke (no lack of power) due to leakage between the turbo and intake manifold |
| Data List | MAP |
| Main fault | ·
Air leak in the turbocharged air passage ·
ECM not operating well ·
Turbocharger sub-assembly (turbine, bearing) |
| Symptoms | Lack of power (when vehicle is starting, under heavy load)
(Black smoke is not emitted when racing while vehicle is stopped) |
| Data List | MAP
·
With the engine switch on (IG) or during idling, MAP = atmospheric pressure (standard atmospheric pressure = 101 kPa). When the engine speed is about 1500 rpm or more, the turbocharger starts to take effect and MAP becomes higher than atmospheric pressure. ·
Atmospheric pressure decreases by 1 kPa each time elevation increases by 100 m, and is also affected by the current weather conditions. |
| Main fault | Blockage |
| Symptoms | Lack of power (high engine speed, under heavy load) |
| Main fault | Glow system malfunction |
| Symptoms | Difficult to start, rough idle, knocking, white smoke (when cold) |
| Data List | Check the glow plug indicator light |
| Diagnostic Point | Measure the resistance of the glow plug |
| Main fault | Battery is depleted |
| Symptoms | Difficult to start (cannot crank, crank speed is low), horn is quiet |
| Data List | Battery Voltage
When cranking, battery voltage is below 5 V. |
| Main fault | Damaged, seized up |
| Symptoms | Cannot crank, crank speed is low, strange noise |
| Main fault | Loss of compression |
| Symptoms | Rough idle (lack of power always) |
| Data List | Engine Speed of Cyl
·
When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression. Injection Feedback Val ·
When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder. |
| Main fault | Starter system malfunction |
| Symptoms | Difficult to start |
| Data List | Starter Signal
·
Engine switch (STA) output: Open: Starter is operating Close: Starter is not operating |
Diesel Injection
| Main fault | - |
| Symptoms | Difficult to start, engine stalling, rough idle, lack of power |
| Data List | Common Rail Pressure, Target Common Rail Pressure, Target Pump SCV Current
·
Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)). ·
If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt. ·
If the fuel pressure is below 25000 kPa, then idling will be rough.
|
| Diagnostic Trouble Code | Even if Common Rail Pressure is below Target Common Rail Pressure, a DTC will not be stored. |
| Main fault | Blockage |
| Symptoms | Difficult to start, engine stalling, rough idle, lack of power |
| Data List | Common Rail Pressure, Target Common Rail Pressure
·
Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)). ·
If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt. ·
If the fuel pressure is below 25000 kPa, then idling will be rough.
|
| Diagnostic Trouble Code | Even if Common Rail Pressure is below Target Common Rail Pressure, a DTC will not be stored. |
| Main fault | Blockage |
| Symptoms | Rough idle, lack of power, black smoke, white smoke, knocking |
| Data List | Injection Feedback Val
·
When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder. This value can be read after idling for 1 minute. |
| Main fault | Does not completely close |
| Symptoms | Difficult to start, engine stall, rough idle, lack of power |
| Main fault | Circuit fault: The injector assembly does not open. |
| Symptoms | Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking |
| Data List | Same as injector assembly |
| Diagnostic Trouble Code | When the injector driver has a fault, some DTCs may be stored. |
| Main fault | Open circuit, decrease in performance (foreign matter is stuck) |
| Symptoms | Difficult to start, rough idle, engine stall, lack of power |
| Data List | Common Rail Pressure, Target Common Rail Pressure
·
Slowly raise the engine speed from idling to 3000 rpm with the vehicle stopped and check that Common Rail Pressure follow Target Common Rail Pressure. If the fuel pressure sensor malfunctions, the actual fuel pressure may deviate from the target fuel pressure (either Common Rail Pressure decreases to a value less than Target Common Rail Pressure). |
| Diagnostic Trouble Code | When the fuel pressure sensor has a fault, some DTCs may be stored. |
| Main fault | - |
| Symptoms | Difficult to start, rough idle (especially when cold) |
Diesel EGR
| Main fault | ·
Does not move smoothly ·
Does not close completely |
| Symptoms | ·
Rough idle ·
EGR valve stuck closed: A loud turbocharger sound. ·
EGR valve stuck open: Difficult to start (does not stall), black smoke, lack of power (if there is an excess in the quantity of EGR and there is a heavy load, when the vehicle starts moving, a lack of power will be felt). |
| Data List | Actual EGR Valve Pos, Actual EGR Valve Pos #2, Target EGR Valve Pos, Target EGR Valve Pos #2
·
Generally, Actual EGR Valve Pos = Target EGR Valve Pos +/-5% (fully closed: 0%, fully open: 100%). ·
Using the EGR valve Active Test, check whether Actual EGR Valve Pos follows Target EGR Valve Pos (the engine coolant temperature and intake air temperature should be considered when a malfunction occurs). ·
EGR valve is fully closed when the engine switch is turned to on (IG) (engine stopped). ·
EGR valve opens to the halfway point at idling after the engine is warmed up. EGR Close Lrn. Val., EGR Close Lrn. Val. #2 ·
When leaving the vehicle idling, the normal range of EGR Close Lrn. Val. is 3.5 to 4.5 V. ·
In cases when EGR Close Lrn. Val. is out of the normal range (3.5 to 4.5 V), it is possible that the EGR valve cannot completely close. |
Diesel Throttle
| Main fault | Stuck, does not move smoothly |
| Symptoms | ·
Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed. ·
Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur. |
| Data List | ·
Actual Throttle Position, Actual Throttle Position #2 100%: Fully open 0%: Fully closed ·
When the engine switch is on (IG) (the engine is stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the engine switch is turned from on (IG) to off, the throttle is fully closed temporarily. |
Data List Related to Starting Trouble
MAP
MAF
Intake Air
Coolant Temp
Battery Voltage
Starter Signal
Engine Speed of Cyl #1 (to #8)
Target Common Rail Pressure
Common Rail Pressure
Target Pump SCV Current
Injection Feedback Val #1 (to #8)
Injection Volume
Actual Throttle Position
Actual Throttle Position #2
Target EGR Valve Pos.
Target EGR Valve Pos #2
Actual EGR Valve Pos
Actual EGR Valve Pos #2
EGR Close Lrn. Val.
EGR Close Lrn. Val #2
Explanation of Symptom
| Starting Trouble | For good starting it is essential to have:
·
Sufficient cranking speed. ·
Properly operating engine preheating system. ·
Good quality fuel. The fuel is ignited by the heat which is generated by compression pressure. With problems such as a depleted battery, the crankshaft speed can become low, or if the engine compression is poor due to leakage, the compression pressure will not rise and there will be difficulty starting. When the engine is cold, even if there is compression heat, it will escape from the combustion chamber. For this reason, when the engine is started when it is cold, the glow plugs heat the compressed air. Also, after starting the engine, by charging the glow plugs for a fixed time set according to the engine coolant temperature, diesel knocking and white smoke are prevented. The quantity of fuel injected is determined by the fuel pressure and also the amount of time the injector assembly is open. |
Trouble Area Chart According to Problem Cause
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).
Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle age. Do not assume the vehicle is normal when the Data List outputs standard values. There may be concealed factors of the malfunction.
Check the engine cranking condition.
| Result | Proceed to |
|---|---|
| Cranking is OK. | A |
Low cranking speed.
|
B |
| Does not crank at all. | C |
A
B
C
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Utility / All Codes.
| Result | Proceed to |
|---|---|
| No DTC is output | A |
| Engine related DTCs are output | B |
If only DTC P1604 is output, proceed to step 3.
A
B
(See pageEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DIAGNOSTIC TROUBLE CODE CHART)
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Engine and ECT / Data List / All Data.
Take a snapshot when idling with no load after the engine is warmed up and when starting trouble is occurring.
A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the illustration below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.
When there is trouble starting with a cold engine, take the snapshot when the engine is cold. Then warm up the engine (engine coolant temperature is 70°C (158°F) or higher) and after idling the vehicle for 1 minute (A/C off, electrical load off), take a snapshot of the data for 15 seconds while idling.
Take a snapshot when the problem is occurring, such as when the engine is cold. However, if the problem does not reoccur, it is acceptable to only take a snapshot after the engine is warmed up and when the engine is started.
NEXT
Check Common Rail Pressure in the snapshot taken in procedure 3 when the engine was started.
| Result | Proceed to |
|---|---|
| At the point in the illustration labeled "a", Common Rail Pressure is less than 10000 kPa from the value of Common Rail Pressure when cranking starts | A |
| At the point in the illustration labeled "c", Common Rail Pressure is below Target Common Rail Pressure by 15000 kPa or more | B |
| Common Rail Pressure increases to a value that is higher than Target Common Rail Pressure immediately after cranking, and, at the point in the illustration labeled "d", Common Rail Pressure is higher than Target Common Rail Pressure | C |
| Except above | D |
Even if Common Rail Pressure is temporarily higher than Target Common Rail Pressure, as shown at the point in the illustration labeled "b", the fuel supply pump assembly is normal.
Common Rail Pressure is about 25000 to 35000 kPa when the engine is cranking and the engine coolant temperature is 0°C (32°F) or higher.
Common Rail Pressure increases rapidly during cranking.
A
B
C
D
Disconnect the inlet hose from the fuel supply pump assembly.
Operate the priming pump and check that fuel is being supplied to the fuel supply pump assembly.
Fuel is properly supplied to the fuel supply pump assembly when the priming pump is operated.
When there is a lack of fuel, fuel pressure drops.
Inspect for fuel filter clogging (check that the fuel filter is not clogged).
Reconnect the inlet hose.
OK
NG
Disconnect the suction control valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z64-1 (+B) - C45- 104 (PCV+) | Always | Below 1 Ω |
| z64-2 (PCV) - C45-105 (PCV-) | Always | Below 1 Ω |
| z64-1 (+B) or C45- 104 (PCV+) - Body ground | Always | 10 kΩ or higher |
| z64-2 (PCV) or C45-105 (PCV-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z64-1 (+B) - C46- 104 (PCV+) | Always | Below 1 Ω |
| z64-2 (PCV) - C46-105 (PCV-) | Always | Below 1 Ω |
| z64-1 (+B) or C46- 104 (PCV+) - Body ground | Always | 10 kΩ or higher |
| z64-2 (PCV) or C46-105 (PCV-) - Body ground | Always | 10 kΩ or higher |
Reconnect the suction control valve connector.
Reconnect the ECM connector.
OK
NG
Replace the supply pump assembly (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL).
NEXT
Bleed the air from the fuel system (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL SYSTEM(w/ DPF)>ON-VEHICLE INSPECTION).
Perform PM forced regeneration (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).
When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.
NEXT
Perform supply pump initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Engine and ECT / Data List / Common Rail Pressure.
Start the engine.
Read the Fuel Press values while cranking and idling the engine.
| Result | Proceed to |
|---|---|
| The engine cannot be started or the engine can be started but Common Rail Pressure is below 20000 kPa 2 seconds after the starter signal changes from OFF to ON | B |
| Except above | A |
A
B
Remove the glow plug assembly for all the cylinders (See page Engine / Hybrid System>1VD-FTV (STARTING)>GLOW PLUG>REMOVAL).
Visually check if there is fuel on the glow plugs.
If there is fuel on a glow plug, fuel may be leaking from an injector assembly.
After replacing an injector assembly, make sure that the common rail pressure is within 5000 kPa of the target fuel pressure while cranking the engine.
If there is fuel on a glow plug, fuel may have mixed with the engine oil. Check the engine oil amount and whether the engine oil smells of diesel fuel. If the oil level is above the full line or the engine oil smells of diesel fuel, replace the engine oil.
Install the glow plug assembly (See page Engine / Hybrid System>1VD-FTV (STARTING)>GLOW PLUG>INSTALLATION).
NEXT
Check and repair or replace the clogged fuel pipe.
NEXT
Bleed the air from the fuel system (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL SYSTEM(w/ DPF)>ON-VEHICLE INSPECTION).
Perform PM forced regeneration (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).
When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.
NEXT
Check Common Rail Pressure in the snapshot taken in procedure 3 when the engine was warmed up.
| Result | Proceed to |
|---|---|
| Difference between Common Rail Pressure and Target Common Rail Pressure is 5000 kPa (51.0 kgf/cm2, 725 psi) or more | A |
| Except above | B |
A
B
Replace the fuel supply pump assembly (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL).
NEXT
Perform supply pump initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
NEXT
Replace the injector assemblies (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL INJECTOR (w/ DPF)>REMOVAL).
When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.
Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.
NEXT
When the engine does not start, perform the following procedure.
Stop the engine and leave the vehicle for 4 hours or more.
It is necessary to leave the vehicle for 4 hours or more to wait for air in the injector assembly to come out.
Check that the engine starts.
The engine starts.
When the engine starts, perform the following procedure.
Bleed the air from the fuel system (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL SYSTEM(w/ DPF)>ON-VEHICLE INSPECTION).
Check that the engine starts.
The engine starts.
OK
NG
Check Injection Feedback Val # in the snapshot taken in procedure 3 when the engine was idling.
| Result | Proceed to |
|---|---|
| Injection Feedback Val #1 to #8 are 3 mm3/st or less.
Injection Volume is more than 13 mm3/st. |
A* |
Injection Feedback Val for at least one cylinder is more than +3 mm3/st
|
B |
| Except above | C |
*: When this case occurs, usually symptoms may be noticeable, such as difficulty starting or lack of power.
The shift lever should be in neutral and the A/C switch and all accessory switches should be off.
A
B
C
Replace the injector assemblies (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL INJECTOR (w/ DPF)>REMOVAL).
When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.
Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.
NEXT
Use this Active Test to help determine whether a cylinder has compression loss or not.
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Engine and ECT / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #8.
Check the engine speed during the Active Test.
| Result | Proceed to |
|---|---|
| Except below | A |
| The values of Engine Speed Cyl #1 to #8 are within +/-10 rpm of each other. | B |
When cranking, if the speed of a cylinder is approximately 100 rpm more than the other cylinders, there is probably a complete loss of compression in that cylinder.
A
B
Measure the compression of the cylinder that had a high speed during the "Check the Cylinder Compression" Active Test.
Check the cylinder compression pressure (See page Engine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).
OK
NG
It can be determined that the injector assembly is faulty as the corresponding cylinder is malfunctioning, but has no compression loss.
Replace the injector assembly (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL INJECTOR (w/ DPF)>REMOVAL).
When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.
Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.
NEXT
Clean the fuel filter case and replace the fuel filter.
Be sure to clean the inside of the fuel filter case as the fuel injectors may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.
NEXT
Bleed the air from the fuel system (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL SYSTEM(w/ DPF)>ON-VEHICLE INSPECTION).
Perform PM forced regeneration (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).
When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.
NEXT
Register the injector compensation codes (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).
Perform the injector pilot quantity learning (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).
NEXT
NEXT
Even in cases where DTC P062D and P062E are not stored even though the engine cannot be started, perform the DTC P062D troubleshooting procedure (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P0201).
When the engine cannot be started due to a malfunction in the injector driver system, once the DTCs are cleared, the system cannot store DTC P062D and P062E even if it is confirmed that the engine cannot be started when trying to reproduce the problem symptoms.
As DTC P062D and P062E cannot be stored when starting the engine, fuel injection signals are output by the ECM, but fuel is not actually injected. Therefore, an excessive amount of fuel is supplied to the common rail by the fuel supply pump assembly, and as a result, the fuel pressure is higher than the target common rail pressure in the data recorded at the time the engine was having trouble starting.
If the problem cannot be determined even after performing the DTC P062D and P062E troubleshooting procedure and the fuel pressure is higher than the target common rail pressure when attempting to start the engine, proceed to the next step.
| Result | Proceed to |
|---|---|
| Injector driver (EDU) circuit is normal | A |
| Injector driver (EDU) circuit is abnormal | B |
A
B
When the engine does not start, perform the following procedure.
Stop the engine and leave the vehicle for 4 hours or more.
It is necessary to leave the vehicle for 4 hours or more to wait for air in the injector assembly to come out.
Confirm the engine starts.
When the engine starts, perform the following procedure.
Bleed the air from the fuel system (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL SYSTEM(w/ DPF)>ON-VEHICLE INSPECTION).
Confirm the engine starts.
NEXT
Check the temperature when starting trouble occurs.
| Result | Proceed to |
|---|---|
| Difficult to start only for cold engine. | A |
| Difficult to start both for cold and warmed up engine. | B |
A
B
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Engine and ECT / Data List / All Data / Coolant Temp.
Read the value displayed on the GTS.
Coolant Temp is not high when the engine is cold, and not low after the engine is warmed up
OK
NG
(See pageEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION)
Inspect the glow plug (See page Engine / Hybrid System>1VD-FTV (STARTING)>GLOW PLUG>ON-VEHICLE INSPECTION).
OK
NG
Check that only diesel fuel is being used.
Check that the fuel does not contain any impurities.
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| No DTC is output | A |
| Engine related DTCs are output | B |
A
B
(See pageEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DIAGNOSTIC TROUBLE CODE CHART)
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Check if the normal starting screen appears (check whether communication with the ECM is possible).
Use a GTS that is able to communicate with other vehicles.
Communication is possible (vehicle can be recognized).
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Engine and ECT / Data List / All Data / Starter Signal and Neutral Position SW Signal.
Read the value displayed on the GTS.
| GTS Display | Condition | Specified Condition |
|---|---|---|
| Starter Signal | Cranking | Open |
| Neutral Position SW Signal | Shift lever in neutral | ON |
OK
NG
Inspect the starting system.
Be sure to inspect the following areas:
Starter relay
Starter assembly
Immobiliser system
NEXT
NEXT