Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/o Secondary Air Injection System) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0255032 SFI SYSTEM J

3UR-FE ENGINE CONTROL  SFI SYSTEM  Fuel Pump Control Circuit  


DESCRIPTION

The fuel pump circuit consists of the ECM, fuel pump and fuel pump ECU (which operates the fuel pump). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump ECU. Based on the signal sent from the ECM, the fuel pump ECU adjusts the fuel pump operation speed.

WIRING DIAGRAM

A263015E02
2.278,1.026 2.391,1.182 0.113,0.156 10 1 1.452,1.035 1.550,1.191 0.098,0.156 10 2 2.278,0.611 2.391,0.767 0.113,0.156 10 3 1.452,0.62 1.550,0.775 0.098,0.156 10 5 1.707,1.463 2.673,1.609 0.966,0.146 10 EFI NO. 2 2.442,2.528 2.544,2.670 0.102,0.142 10 4 1.136,4.172 1.234,4.317 0.098,0.145 10 3 2.627,2.528 2.816,2.666 0.189,0.138 10 1B 1.321,4.171 1.509,4.312 0.187,0.140 10 1B 1.984,3.731 2.296,3.880 0.312,0.149 10 EFI 0.823,3.139 1.466,3.295 0.642,0.156 10 EFI MAIN 2.947,3.226 3.044,3.371 0.098,0.145 10 2 2.89,3.406 3.077,3.546 0.187,0.140 10 1B 0.465,4.166 0.567,4.308 0.102,0.142 10 1 0.648,4.167 0.846,4.306 0.198,0.138 10 1C 1.748,4.4 2.822,4.542 1.074,0.142 10 Integration Relay 1.019,5.876 1.484,6.025 0.465,0.149 10 Battery 4.283,4.334 4.564,4.483 0.281,0.149 10 N1 4.283,4.497 4.988,4.649 0.705,0.152 10 Fuel Pump 5.025,3.536 5.123,3.681 0.098,0.145 10 5 4.135,3.536 4.237,3.678 0.102,0.142 10 4 4.295,3.74 4.492,3.893 0.197,0.153 10 B2 4.765,3.74 4.964,3.890 0.199,0.150 10 E2 4.303,2.602 4.415,2.757 0.113,0.156 10 1 5.038,2.598 5.136,2.754 0.098,0.156 10 2 4.18,2.368 4.393,2.517 0.213,0.149 10 FP 4.874,2.368 5.127,2.517 0.253,0.149 10 FP- 3.95,1.798 4.047,1.943 0.098,0.145 10 3 4.148,1.9 4.264,2.046 0.117,0.146 10 E 4.133,0.715 4.334,0.861 0.201,0.146 10 +B 3.958,0.624 4.056,0.769 0.098,0.145 10 6 4.813,0.713 5.115,0.859 0.302,0.145 10 FPC 5.207,0.62 5.320,0.776 0.113,0.156 10 5 4.291,1.3 4.983,1.613 0.692,0.312 10 Fuel Pump ECU 5.844,0.718 6.109,0.865 0.265,0.147 10 A38 5.854,5.223 6.118,5.371 0.265,0.147 10 A38 6.437,5.721 6.770,5.870 0.333,0.149 10 ECM 5.903,5.048 6.080,5.194 0.177,0.145 10 34 6.217,5.227 6.625,5.372 0.408,0.145 10 MREL 5.894,0.544 6.071,0.690 0.177,0.145 10 52 6.208,0.72 6.503,0.876 0.295,0.156 10 FPC 0.331,0.894 1.106,1.061 0.774,0.167 10 EFI MAIN 2 4.288,1.137 4.655,1.292 0.367,0.155 10 N14

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP/SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.


e.

Check whether operating sounds can be heard while operating the fuel pump using the GTS.

OK:

Operating sounds can be heard from fuel pump.



Result
Result Proceed to
NG A
OK B


A

2.INSPECT FUEL PUMP ECU (POWER SOURCE VOLTAGE)

B

13.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP)
2.INSPECT FUEL PUMP ECU (POWER SOURCE VOLTAGE)
U163415E01
2.404,1.917 2.598,2.070 0.194,0.152 10 +B 2.212,1.446 2.506,1.903 false 0.244,1.227 0.526,1.369 0.282,0.142 10 N14 0.048,0.039 2.400,0.383 2.353,0.344 10 Front view of wire harness connector: (to Fuel Pump ECU)

a.

Disconnect the fuel pump ECU connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N14-6 (+B) - Body Ground Engine switch on (IG) 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - BODY GROUND)

NG

9.INSPECT EFI NO.2 RELAY
3.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - BODY GROUND)
a.

Disconnect the fuel pump ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N14-3 (E) - Body ground Always Below 1 Ω




OK

4.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP ECU)
a.

Disconnect the fuel pump connector.


b.

Disconnect the fuel pump ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N1-4 (B2) - N14-1 (FP) Always Below 1 Ω
N1-5 (E2) - N14-2 (FP-) Always Below 1 Ω
N1-4 (B2) or N14-1 (FP) - Body ground Always 10 kΩ or higher
N1-5 (E2) or N14-2 (FP-) - Body ground Always 10 kΩ or higher




OK

5.INSPECT FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FUEL PUMP
a.


OK

6.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM)

NG

6.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM)
a.

Disconnect the fuel pump ECU connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N14-5 (FPC) - A38-52 (FPC) Always Below 1 Ω
N14-5 (FPC) or A38-52 (FPC) - Body ground Always 10 kΩ or higher




OK

7.REPLACE FUEL PUMP ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE FUEL PUMP ECU
a.

Replace the fuel pump ECU (See page Engine / Hybrid System>3UR-FE (FUEL)>FUEL PUMP ECU>REMOVAL).



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check the fuel pump operation.

OK:

Malfunction has been repaired successfully.




OK

END

NG

9.INSPECT EFI NO.2 RELAY

OK

10.CHECK EFI NO.2 RELAY (POWER SOURCE VOLTAGE)

NG

REPLACE EFI NO.2 RELAY

10.CHECK EFI NO.2 RELAY (POWER SOURCE VOLTAGE)
A300177E01
0.098,0.066 1.828,0.249 1.730,0.184 10 Engine Room Relay Block: 1.106,0.902 1.824,1.081 0.718,0.179 10 EFI NO.2

a.

Remove the EFI NO.2 relay from the engine room relay block.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
EFI NO.2 relay (1) - Body ground Engine switch on (IG) 11 to 14 V
EFI NO.2 relay (5) - Body ground Always 11 to 14 V




OK

11.CHECK HARNESS AND CONNECTOR (EFI NO.2 RELAY - FUEL PUMP ECU)

NG

12.CHECK HARNESS AND CONNECTOR (EFI NO.2 RELAY - INTEGRATION RELAY, BATTERY AND BODY GROUND)
11.CHECK HARNESS AND CONNECTOR (EFI NO.2 RELAY - FUEL PUMP ECU)
a.

Remove the EFI NO.2 relay from the engine room relay block.


b.

Disconnect the fuel pump ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI NO.2 relay (3) - N14-6 (+B) Always Below 1 Ω
EFI NO.2 relay (3) or N14-6 (+B) - Body ground Always 10 kΩ or higher




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL PUMP RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (EFI NO.2 RELAY - INTEGRATION RELAY, BATTERY AND BODY GROUND)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Remove the EFI NO.2 relay from the engine room relay block.


d.

Remove the integration relay from the engine room relay block.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI NO.2 relay (1) - 1B-4 Always Below 1 Ω
EFI NO.2 relay (5) - Battery positive (+) terminal Always Below 1 Ω
EFI NO.2 relay (2) - Body ground Always Below 1 Ω
EFI NO.2 relay (1) or 1B-4 - Body ground Always 10 kΩ or higher
EFI NO.2 relay (5) or Battery positive (+) terminal - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP)
A243665E01
2.862,1.37 2.973,1.519 0.111,0.149 10 1 0.647,1.391 0.755,1.544 0.107,0.152 10 2 1.931,1.67 2.821,1.462 false 1.539,1.671 0.796,1.478 false 0.178,0.144 2.543,0.541 2.365,0.397 10 Component with harness connected: (Fuel Pump)

a.

Remove the fuel tank assembly (See page Engine / Hybrid System>3UR-FE (FUEL)>FUEL TANK>REMOVAL).


b.

Remove the fuel pump from the fuel tank assembly.


c.

Clean the fuel pump to completely remove any remaining fuel.


d.

Connect the fuel pump connector.

CAUTION:

Confirm that no fuel remains inside or on the outside of the fuel pump.



e.

Connect the GTS to the DLC3.


f.

Turn the engine switch on (IG).


g.

Turn the tester on.


h.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump Duty.


i.

Operate the fuel pump using the Active Test function and measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Tester Operation Specified Condition
1 - 2 FPC Duty: 25% 3.2 to 4.05 V
FPC Duty: 80% 8.8 to 12.5 V



j.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.


k.

Operate the fuel pump using the Active Test function and measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Tester Operation Specified Condition
1 - 2 ON (FPC Duty: 90%) 9.0 to 14.0 V



HINT:
·

Be sure to measure the voltage with all of the connectors connected.

·

Before performing this inspection, check that the battery voltage is between 11 and 14 V (not depleted).




OK

14.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM)

NG

16.REPLACE FUEL PUMP ECU
14.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM)
a.

Disconnect the fuel pump ECU connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N14-5 (FPC) - A38-52 (FPC) Always Below 1 Ω
N14-5 (FPC) or A38-52 (FPC) - Body ground Always 10 kΩ or higher




OK

15.REPLACE FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.REPLACE FUEL PUMP
a.

Replace the fuel pump (See page Engine / Hybrid System>3UR-FE (FUEL)>FUEL PUMP>REMOVAL).



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
16.REPLACE FUEL PUMP ECU
a.

Replace the fuel pump ECU (See page Engine / Hybrid System>3UR-FE (FUEL)>FUEL PUMP ECU>REMOVAL).



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check the fuel pump operation.

OK:

Malfunction has been repaired successfully.




OK

END

NG