Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/o Secondary Air Injection System) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0255032 SFI SYSTEM J

3UR-FE ENGINE CONTROL  SFI SYSTEM  Fuel Injector Circuit  


DESCRIPTION

The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK INJECTOR ASSEMBLY (POWER SOURCE)
U155682E03
0.281,1.302 0.5,1.469 0.219,0.167 10 false a1 0.781,1.313 1,1.479 0.219,0.167 10 false a5 0.281,1.656 0.5,1.823 0.219,0.167 10 false a2 0.792,1.635 1.01,1.802 0.219,0.167 10 false a6 0.292,1.979 0.51,2.146 0.219,0.167 10 false a3 0.802,2.01 1.021,2.177 0.219,0.167 10 false a7 0.281,2.344 0.5,2.51 0.219,0.167 10 false a4 0.792,2.344 1.01,2.51 0.219,0.167 10 false a8 0.063,0 2.417,0.365 2.354,0.365 10 false Front view of wire harness connector: (to Injector)

a.

Disconnect the fuel injector connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Cylinder Tester Connection Switch Condition Specified Condition
No. 1 a5-2 - Body ground Engine switch on (IG) 11 to 14 V
No. 2 a1-2 - Body ground Engine switch on (IG) 11 to 14 V
No. 3 a6-2 - Body ground Engine switch on (IG) 11 to 14 V
No. 4 a2-2 - Body ground Engine switch on (IG) 11 to 14 V
No. 5 a7-2 - Body ground Engine switch on (IG) 11 to 14 V
No. 6 a3-2 - Body ground Engine switch on (IG) 11 to 14 V
No. 7 a8-2 - Body ground Engine switch on (IG) 11 to 14 V
No. 8 a4-2 - Body ground Engine switch on (IG) 11 to 14 V




OK

2.INSPECT FUEL INJECTOR ASSEMBLY

NG

4.INSPECT INTEGRATION RELAY (IG2)
2.INSPECT FUEL INJECTOR ASSEMBLY
a.


OK

3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)

NG

REPLACE FUEL INJECTOR ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
a.

Disconnect the fuel injector connector.


b.

Disconnect the C45 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Cylinder Tester Connection Condition Specified Condition
No. 1 a5-1 - Body ground Always 10 kΩ or higher
a5-1 - C45-86 (#10) Always Below 1 Ω
No. 2 a1-1 - Body ground Always 10 kΩ or higher
a1-1 - C45-109 (#20) Always Below 1 Ω
No. 3 a6-1 - Body ground Always 10 kΩ or higher
a6-1 - C45-85 (#30) Always Below 1 Ω
No. 4 a2-1 - Body ground Always 10 kΩ or higher
a2-1 - C45-108 (#40) Always Below 1 Ω
No. 5 a7-1 - Body ground Always 10 kΩ or higher
a7-1 - C45-84 (#50) Always Below 1 Ω
No. 6 a3-1 - Body ground Always 10 kΩ or higher
a3-1 - C45-107 (#60) Always Below 1 Ω
No. 7 a8-1 - Body ground Always 10 kΩ or higher
a8-1 - C45-83 (#70) Always Below 1 Ω
No. 8 a4-1 - Body ground Always 10 kΩ or higher
a4-1 - C45-106 (#80) Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INTEGRATION RELAY (IG2)
a.

Inspect the integration relay (IG2) (See page Engine / Hybrid System>3UR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY - FUEL INJECTOR ASSEMBLY)

NG

REPLACE INTEGRATION RELAY