Home › Engine / Hybrid System › 1GR-FE (ENGINE MECHANICAL) › ENGINE UNIT
RM2660E _51 Engine / Hybrid System _052778 1GR-FE ENGINE MECHANICAL _0255061 ENGINE UNIT A

1GR-FE ENGINE MECHANICAL  ENGINE UNIT  REMOVAL  


PROCEDURE

Hide 1.REMOVE ENGINE WIRE

Hide 2.DISCONNECT HEATER WATER HOSE ASSEMBLY

a.
A271020E02
0.021,0.021 0.302,0.271 0.281,0.25 10 true *A 0.021,2.49 0.313,2.74 0.292,0.25 10 true *B

Remove the 2 bolts and disconnect the 2 water hoses.

Text in Illustration
*A w/o ATF Warmer
*B w/ ATF Warmer


Hide 25701B 3.REMOVE NO. 1 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)

Hide 25702B 4.REMOVE NO. 2 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)

Hide 6.REMOVE FUEL PIPE SUB-ASSEMBLY

a.
A224750

Disconnect the 2 fuel pipes (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).


b.

Remove the 2 bolts and No. 1 and No. 2 fuel pipes.


Hide 23807 7.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23250 8.REMOVE FUEL INJECTOR ASSEMBLY

Hide 16206 10.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 16603 11.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 16604 12.REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

Hide 16620 13.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 11452 14.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 12315 15.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH

a.
A221156

Remove the 3 bolts and front No. 1 engine mounting bracket LH.


Hide 12311 16.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH

a.
A221155

Remove the 4 bolts and front No. 1 engine mounting bracket RH.


Hide 13453 17.REMOVE FLYWHEEL RING GEAR (for Manual Transmission)

HINT:

If the flywheel ring gear is deformed or the gears are damaged, replace it.


CAUTION:

Wear protective gloves. Hot areas on the flywheel ring gear may injure your hands.


a.
A177669E01
1.248,2.868 1.372,3.010 0.124,0.142 10 1 2.226,3.838 2.350,3.980 0.124,0.142 10 2 0.58,3.528 0.704,3.670 0.124,0.142 10 3 2.713,3.395 2.837,3.538 0.124,0.142 10 4 1.178,3.989 1.302,4.132 0.124,0.142 10 5 2.145,2.86 2.269,3.003 0.124,0.142 10 6

Using a torch, heat the ring gear evenly to approximately 200°C (392°F).


b.

Temporarily install 6 bolts (8 mm (0.315 in.) x 1.25 pitch) with a length of 70 mm (2.76 in.) or more to the flywheel.


c.

Uniformly tighten the 6 bolts in the order shown in the illustration.


d.

Remove the ring gear from the flywheel.