Home › Engine / Hybrid System › 1GR-FE (ENGINE MECHANICAL) › ENGINE UNIT › 2014.08–2020.06
RM2660E _51 Engine / Hybrid System _052778 1GR-FE ENGINE MECHANICAL _0255061 ENGINE UNIT A

1GR-FE ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 83520 1.REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY

Hide 11415 3.REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

a.

for Type A:

i.
A221157

Remove the 2 cylinder block water drain cock plugs from the 2 cylinder block water drain cocks.


ii.

Remove the 2 cylinder block water drain cocks from the cylinder block.



b.

for Type B:

i.
A273790

Remove the cylinder block water drain cock plug from the cylinder block water drain cock.


ii.

Remove the cylinder block water drain cock from the cylinder block.



Hide 11301M 4.REMOVE VVT SENSOR (for Intake Side of Bank 1)

Hide 11301M 5.REMOVE VVT SENSOR (for Exhaust Side of Bank 1)

Hide 11301M 6.REMOVE VVT SENSOR (for Intake Side of Bank 2)

Hide 11301M 7.REMOVE VVT SENSOR (for Exhaust Side of Bank 2)

Hide 15330B 9.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side of Bank 1)

Hide 15330B 10.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side of Bank 1)

Hide 15330B 11.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side of Bank 2)

Hide 15340 12.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side of Bank 2)

Hide 12185 13.REMOVE OIL FILLER CAP HOUSING

a.
A221161

Remove the oil filler cap.


b.

Remove the 2 nuts, oil filler cap housing and gasket.


Hide 16356 19.REMOVE REAR WATER BY-PASS JOINT

a.
A076534

Remove the 2 bolts, 4 nuts, rear water by-pass joint and 2 gaskets.


b.

Remove the O-ring from the No. 1 water outlet pipe.


Hide 11202 23.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

a.
A226542

Remove the 12 bolts, seal washer, cylinder head cover and gasket.

HINT:

Make sure the removed parts are returned to the same places they were removed from.



b.
A223665

Remove the 3 gaskets.


Hide 11201 24.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A226543

Remove the 12 bolts, seal washer, cylinder head cover and gasket.

HINT:

Make sure the removed parts are returned to the same places they were removed from.



b.
A221164

Remove the 3 gaskets.


Hide 11193 25.REMOVE SPARK PLUG TUBE GASKET

A124195

a.

Bend the ventilation baffle plate claws on the cylinder head cover to an angle of 90° or more.

Text in Illustration
V100135

Pry


b.

Remove the 6 spark plug tube gaskets.

HINT:

Be careful not to damage the gasket when removing it as the removed gasket needs to be used when installing a new one.



Hide 12101A 27.REMOVE OIL PAN DRAIN PLUG

a.

Remove the drain plug and gasket.


Hide 12102A 28.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

Hide 15104 29.REMOVE OIL STRAINER SUB-ASSEMBLY

Hide 12121 31.REMOVE NO. 1 OIL PAN BAFFLE PLATE

a.
A224779

Remove the 6 bolts and No. 1 oil pan baffle plate.


Hide 11381 32.REMOVE ENGINE REAR OIL SEAL RETAINER

a.
A076247E08
0.802,0.25 0.99,0.427 0.188,0.177 0.792,0.26 0.969,0.438 0.177,0.177 10 false *a

Remove the 5 bolts and 2 nuts.


b.

Using a screwdriver, remove the oil seal retainer by prying between the oil seal retainer and crankshaft bearing cap.

Text in Illustration
*a Pry

HINT:

Tape the screwdriver tip before use.



Hide 11381A 33.REMOVE REAR CRANKSHAFT OIL SEAL

a.
A076248

Using a screwdriver and hammer, tap out the oil seal.

NOTICE:

Be careful not to damage the rear oil seal retainer.



Hide 11302 34.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 16100 35.REMOVE ENGINE WATER PUMP ASSEMBLY

a.
A221171

Remove the 8 bolts, engine water pump and gasket.


Hide 11301C 36.REMOVE FRONT CRANKSHAFT OIL SEAL

Hide 37.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Temporarily install the pulley set bolt.


b.
A222172E04
0.563,0.302 1,0.115 1,0.115 1.115,0.115 true 0.74,0.677 0.583,1.781 0.583,1.781 1.583,0.969 true 2.396,1.958 2.396,1.729 2.396,1.729 2.26,1.552 true 1.135,0.031 1.375,0.24 0.24,0.208 10 true *1 0.479,1.823 0.719,2.083 0.24,0.26 10 true *2 2.302,1.958 2.542,2.156 0.24,0.198 10 true *3

Turn the crankshaft clockwise to align the timing mark on the crank angle sensor plate with the RH block bore center line (TDC/compression).

Text in Illustration
*1 Center Line
*2 Timing Mark
*3 Sensor Plate


c.

Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing caps as shown in the illustration.

A385874E01
1.146,2.031 0.573,1.448 true 1.146,2.042 0.583,1.094 true 1.135,2.031 1.844,1.135 true 1.156,2.021 1.844,1.583 true 5.979,2.083 6.76,1.417 true 5.979,2.083 6.74,1.094 true 5.979,2.073 5.604,1.063 true 5.979,2.104 5.594,1.552 true 1.115,2.083 1.427,2.281 0.313,0.198 10 false *1 5.917,2.125 6.229,2.323 0.313,0.198 10 false *1

If not, turn the crankshaft clockwise 1 revolution (360°) and align the timing marks as above.

Text in Illustration
*1 Timing Mark


Hide 13540 38.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A124589E20
1.063,1.073 1.448,1.729 1.448,1.729 2.656,1.135 true 1.146,0.833 0.958,0.104 0.958,0.104 0.854,0.104 true 2.802,0.854 2.646,0.094 2.646,0.094 2.521,0.094 true 2.688,1.698 2.875,1.698 true 0.646,0.031 0.823,0.208 0.177,0.177 10 true *1 2.281,0.01 2.469,0.188 0.188,0.177 10 true *1 2.885,1.615 3.198,1.865 0.313,0.25 10 true *3 1.385,1.813 1.635,2.031 0.25,0.219 10 true *2

Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.

Text in Illustration
*1 Plunger
*2 Stopper Plate
*3 Pin


b.

Move the stopper plate downward to set the lock, and insert a pin with a diameter of 1.27 mm (0.0500 in.) into the stopper plate hole.


c.
A095165E03
1.563,1.281 1.583,1.333 false 1.646,1.24 1.625,1.219 1.625,1.219 1.635,1.198 false

Remove the 2 bolts and No. 1 chain tensioner assembly.


Hide 13559 39.REMOVE CHAIN TENSIONER SLIPPER

a.
A223730

Remove the chain tensioner slipper.


Hide 13506 40.REMOVE CHAIN SUB-ASSEMBLY

a.
A221173E04
1.073,0.104 0.979,0.104 0.979,0.104 0.51,0.271 true 0.656,0.74 0.615,1.604 0.615,1.604 1.594,0.948 true 2.49,1.698 2.385,1.698 2.385,1.698 2.271,1.542 false 0.5,1.646 0.75,1.854 0.25,0.208 10 true *2 2.51,1.604 2.75,1.833 0.24,0.229 10 true *3 1.156,0.052 1.417,0.271 0.26,0.219 10 true *1

Turn the crankshaft counterclockwise 10° to loosen the chain of the crankshaft timing sprocket.

Text in Illustration
*1 Center Line
*2 Timing Mark
*3 Sensor Plate


b.

Remove the pulley set bolt.


c.
A221174

Remove the chain sub-assembly from the crankshaft timing sprocket and place it on the crankshaft.


d.
A385838E01
0.115,0.073 0.427,0.271 0.313,0.198 10 false *A

Turn the camshaft timing gear assembly on bank 1 clockwise approximately 60° so that it is as shown in the illustration. Be sure to loosen the chain sub-assembly between the banks.


e.

Remove the chain sub-assembly.

Text in Illustration
*A for Bank 1


Hide 13581 41.REMOVE NO. 1 IDLE GEAR SHAFT

a.
A221175

Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, No. 1 idle gear and No. 1 idle gear shaft.


Hide 13561 42.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A223642

Remove the 2 bolts and No. 1 chain vibration damper.


Hide 13562 43.REMOVE NO. 2 CHAIN VIBRATION DAMPER

a.
A221176

Remove the 2 No. 2 chain vibration dampers.


Hide 13521 44.REMOVE CRANKSHAFT TIMING SPROCKET

a.
U147484

Remove the crankshaft timing sprocket.


Hide 45.REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)

a.
A221132E04
1.438,2.948 1.563,2.948 1.563,2.948 1.688,2.656 false 1.729,2.188 1.646,2.188 1.646,2.188 1.531,2.333 false 1.24,2.865 1.396,3.021 0.156,0.156 10 false *1 1.75,2.083 1.938,2.24 0.188,0.156 10 false *2 2.542,1.49 2.76,1.729 0.219,0.24 10 true *a

While raising the No. 2 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the No. 2 chain tensioner assembly.

Text in Illustration
*1 Pin
*2 Plunger
*a Push


b.
A221177E01
0.452,0.131 0.777,0.331 0.325,0.200 10 SST 2.74,0 2.961,0.198 0.221,0.198 10 *a 0.596,1.55 0.817,1.747 0.221,0.198 10 *b 0.845,0.215 0.983,0.215 0.983,0.215 1.297,0.632 false

Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly.

SST
09922-10010  

Text in Illustration
*a Turn
*b Hold

NOTICE:

Do not loosen the other 4 bolts. If any of the 4 bolts is loosened, replace the camshaft timing gear assembly and/or camshaft timing exhaust gear assembly with a new one.



c.

Remove the 2 bolts and camshaft timing gear assembly together with the No. 2 chain.


Hide 13550 46.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A221178

Remove the bolt and No. 2 chain tensioner assembly.


Hide 47.REMOVE CAMSHAFT BEARING CAP (for Bank 1)

a.
A129700E06
1.586,2.144 1.806,2.328 0.221,0.184 10 *a 1.507,3.083 1.704,3.258 0.198,0.174 10 *1 2.991,2.287 3.239,2.471 0.248,0.184 10 45° 1.116,2.54 1.625,3.049 1.625,3.049 2.506,2.574 false

Check that the camshafts are positioned as shown in the illustration.

Text in Illustration
*1 Knock Pin
*a Front View


b.
A221179E07
0.698,0.792 0.917,0.969 0.219,0.177 10 true 1 2.74,0.771 2.927,0.938 0.188,0.167 10 true 3 2.719,0.083 2.854,0.24 0.135,0.156 10 true 4 1.396,0.792 1.604,0.948 0.208,0.156 10 true 5 1.406,0.125 1.542,0.281 0.135,0.156 10 true 6 2.094,0.792 2.313,0.969 0.219,0.177 10 true 7 2.094,0.125 2.229,0.281 0.135,0.156 10 true 8 0.708,0.125 0.844,0.281 0.135,0.156 10 true 2

Uniformly loosen and remove the 8 bearing cap bolts in several steps in the sequence shown in the illustration.


c.
A221180E04
1.031,1.188 1.24,1.375 0.208,0.188 10 true 5 1.01,0.583 1.219,0.75 0.208,0.167 10 true 6 0.854,0.083 1.021,0.26 0.167,0.177 10 true 4 3.083,0.052 3.281,0.292 0.198,0.24 10 true 1 2.417,0.073 2.635,0.271 0.219,0.198 10 true 10 2.385,0.594 2.604,0.781 0.219,0.188 10 true 12 2.417,1.188 2.656,1.365 0.24,0.177 10 true 11 3.063,0.583 3.271,0.781 0.208,0.198 10 true 3 1.74,0.115 1.958,0.333 0.219,0.219 10 true 7 1.729,0.594 1.938,0.771 0.208,0.177 10 true 9 1.729,1.188 1.958,1.375 0.229,0.188 10 true 8 3.01,1.229 3.25,1.469 0.24,0.24 10 true 2

Uniformly loosen and remove the 12 bearing cap bolts in several steps in the sequence shown in the illustration.

NOTICE:

Uniformly loosen the bolts while keeping the camshaft level.



d.

Remove the 5 camshaft bearing caps.


e.

Remove the camshaft and No. 2 camshaft.


Hide 11103C 48.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH

a.
A221181E04
0.396,2.188 0.521,2.188 0.521,2.188 0.573,2.125 true 1.51,3.021 1.51,2.771 true 2.635,2.719 2.635,2.646 2.635,2.646 2.333,2.5 true 2.979,2.667 2.979,2.573 2.979,2.573 3.125,2.24 true 0.219,2.104 0.375,2.292 0.156,0.188 10 false *1 1.427,3.031 1.667,3.219 0.24,0.188 10 true *1 2.563,2.729 2.719,2.917 0.156,0.188 10 false *1 2.875,2.677 3.031,2.865 0.156,0.188 10 false *1

Remove the camshaft housing sub-assembly RH by prying between the cylinder head and camshaft housing sub-assembly RH with a screwdriver.

Text in Illustration
*1 Protective Tape

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head and camshaft housing sub-assembly RH.


HINT:

Tape the screwdriver tip before use.



Hide 49.REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)

a.
A221182E06
2.01,2.542 2.115,2.542 2.115,2.542 2.302,2.229 false 2.24,1.823 2.146,1.823 2.146,1.823 1.938,2.052 false 2.26,1.719 2.448,1.896 0.188,0.177 10 false *1 1.802,2.458 1.99,2.635 0.188,0.177 10 false *2 1.917,0.302 2.219,0.5 0.302,0.198 10 true *a

While pushing down the No. 3 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the No. 3 chain tensioner assembly.

Text in Illustration
*1 Pin
*2 Plunger
*a Push


b.
A223637E01
2.722,0.19 3.100,0.402 0.378,0.211 10 SST 0.307,0 0.509,0.221 0.202,0.221 10 *a 2.962,1.134 3.164,1.355 0.202,0.221 10 *b 2.682,0.272 2.484,0.272 2.484,0.272 1.613,0.756 false

Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly.

SST
09922-10010  

Text in Illustration
*a Turn
*b Hold

NOTICE:

Do not loosen the other 4 bolts. If any of the 4 bolts is loosened, replace the camshaft timing gear assembly and/or camshaft timing exhaust gear assembly with a new one.



c.

Remove the 2 bolts and camshaft timing gear together with the No. 2 chain.


Hide 13560A 50.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

a.
A221183

Remove the bolt and No. 3 chain tensioner assembly.


Hide 51.REMOVE CAMSHAFT BEARING CAP (for Bank 2)

a.
A223636E04
1.167,2.521 1.677,3.063 1.677,3.063 2.313,2.5 false 1.615,2.146 1.802,2.323 0.188,0.177 10 false *a 1.552,3.073 1.74,3.25 0.188,0.177 10 false *1 1.052,2.073 1.396,2.281 0.344,0.208 10 true 15°

Check that the camshafts are positioned as shown in the illustration.

Text in Illustration
*1 Knock Pin
*a Front View


b.
A221184E07
1.125,1.375 1.26,1.573 0.135,0.198 2.469,1.458 2.667,1.688 0.198,0.229 10 true 1 2.458,0.823 2.646,1.052 0.188,0.229 10 true 2 0.302,1.448 0.5,1.688 0.198,0.24 10 true 3 0.281,0.656 0.438,0.865 0.156,0.208 10 true 4 1.792,1.458 1.979,1.656 0.188,0.198 10 true 5 1.781,0.823 1.99,1.042 0.208,0.219 10 true 6 1.146,1.458 1.354,1.667 0.208,0.208 10 true 7 1.156,0.813 1.365,1.073 0.208,0.26 10 true 8

Uniformly loosen and remove the 8 bearing cap bolts in several steps in the sequence shown in the illustration.


c.
A221185E04
0.281,0.615 0.448,0.771 0.167,0.156 10 true 5 1.75,0.656 1.906,0.813 0.156,0.156 10 true 8 2.396,1.208 2.563,1.365 0.167,0.156 10 true 4 1.802,1.771 2.01,1.958 0.208,0.188 10 true 9 2.51,1.729 2.698,1.938 0.188,0.208 10 true 3 3.24,1.375 3.375,1.531 0.135,0.156 10 false 1 3.26,0.656 3.396,0.813 0.135,0.156 10 false 2 0.25,1.104 0.385,1.26 0.135,0.156 10 true 7 0.281,1.771 0.417,1.927 0.135,0.156 10 false 6 1.021,0.615 1.198,0.771 0.177,0.156 10 true 11 0.979,1.083 1.156,1.24 0.177,0.156 10 true 13 1,1.729 1.219,1.927 0.219,0.198 10 true 12 1.677,1.177 1.854,1.333 0.177,0.156 10 true 10

Uniformly loosen and remove the 13 bearing cap bolts in several steps in the sequence shown in the illustration.

NOTICE:

Uniformly loosen the bolts while keeping the camshaft level.



d.

Remove the 5 camshaft bearing caps.


e.

Remove the No. 3 camshaft and No. 4 camshaft.


Hide 11104A 52.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH

a.
A221186E04
0.281,2.219 0.5,1.844 0.5,1.844 0.594,1.844 false 1.635,2.698 1.719,2.698 1.719,2.698 1.719,3 true 2.708,2.188 2.802,2.188 2.802,2.188 2.906,2.083 true 0.615,1.75 0.802,1.906 0.188,0.156 10 false *1 1.438,2.656 1.625,2.813 0.188,0.156 10 true *1 2.521,2.104 2.708,2.26 0.188,0.156 10 true *1

Remove the camshaft housing sub-assembly LH by prying between the cylinder head and camshaft housing sub-assembly LH with a screwdriver.

Text in Illustration
*1 Protective Tape

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head and camshaft housing sub-assembly LH.


HINT:

Tape the screwdriver tip before use.



Hide 13801 53.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Remove the 24 valve rocker arms from the cylinder head.

HINT:

Arrange the removed parts in the correct order.



Hide 13750 54.REMOVE VALVE LASH ADJUSTER ASSEMBLY

a.

Remove the 24 valve lash adjusters from the cylinder head.

HINT:

Arrange the removed parts in the correct order.



Hide 13716 55.REMOVE VALVE STEM CAP

a.

Remove the 24 valve stem caps from the cylinder head.

HINT:

Arrange the removed parts in the correct order.



Hide 11115 58.REMOVE CYLINDER HEAD GASKET

Hide 11116 59.REMOVE NO. 2 CYLINDER HEAD GASKET

Hide 62.REMOVE CYLINDER BLOCK WATER JACKET SPACER

A225372

a.

Remove the 2 water jacket spacers from the cylinder head.

NOTICE:

Be sure to remove the water jacket spacers. If not, they may fall and become damaged when the cylinder block is inverted.



Hide 63.REMOVE TAPER SCREW PLUG

NOTICE:

It is not necessary to remove a taper screw plug unless it is being replaced.


Hide 64.REMOVE STRAIGHT PIN

NOTICE:

It is not necessary to remove a straight pin unless it is being replaced.


Hide 65.REMOVE RING PIN

NOTICE:

It is not necessary to remove a ring pin unless it is being replaced.


Hide 66.REMOVE STUD BOLT

NOTICE:

It is not necessary to remove a stud bolt unless it is being replaced.