Home › Engine / Hybrid System › 1VD-FTV (LUBRICATION) › OIL PUMP › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052799 1VD-FTV LUBRICATION _0255224 OIL PUMP A

1VD-FTV LUBRICATION  OIL PUMP  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing an injector (including interchanging injectors between cylinders) or common rail, replace the corresponding injection pipes with new ones.

·

w/DPF

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


a.

Disconnect the cables from the negative (-) main battery and sub-battery terminals.


Hide 3.REMOVE ENGINE ASSEMBLY

a.

Remove the engine assembly from the vehicle (See page Engine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL).


Hide 27020 5.REMOVE GENERATOR ASSEMBLY

a.
A174761

Remove the nut and bolt, and disconnect the generator positive (+) cable.


b.
A163035

Remove the 3 bolts, 2 nuts and generator.


Hide 11452 7.REMOVE NO. 1 ENGINE OIL LEVEL DIPSTICK GUIDE

a.
A170301

Remove the 2 bolts and No. 1 engine oil level dipstick guide.


Hide 15408G 9.DISCONNECT NO. 2 INLET TURBO OIL PIPE SUB-ASSEMBLY

a.
A177391

Remove the union bolt and gasket, and disconnect the No. 2 inlet turbo oil pipe.


Hide 12158 10.REMOVE STIFFENER INSULATOR RH (w/ Intercooler)

a.
A170322

Remove the 2 bolts and stiffener insulator RH.


Hide 15777 11.DISCONNECT NO. 1 OIL COOLER HOSE

A177371E03
0.448,1.667 0.448,1.531 0.448,1.531 0.979,1.135 true 2.969,1.531 2.969,1.396 2.969,1.396 2.448,1.125 true 0.052,1.698 0.771,1.865 0.719,0.167 10 true No. 2 Hose 2.521,1.552 3.24,1.719 0.719,0.167 10 true No. 1 Hose

Hide 15778 12.DISCONNECT NO. 2 OIL COOLER HOSE

Hide 16620D 13.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

a.
A177437

Remove the 3 bolts and V-ribbed belt tensioner bracket.


b.
A174864

Remove the bolt and No. 1 idler pulley.


c.
A177414

Remove the 5 bolts and V-ribbed belt tensioner.


Hide 11348 15.REMOVE TIMING GEAR COVER SPACER (w/ Intercooler)

a.
A177415

Remove the 2 bolts and timing gear cover spacer.


Hide 15609 17.REMOVE OIL FILTER BRACKET SUB-ASSEMBLY

a.
A174758

Disconnect the 2 wire harness clamps.


b.
A177438

Remove the 3 bolts, 2 nuts and oil filter bracket.


c.
A177439

Remove the 2 O-rings.


Hide 89491 18.REMOVE ENGINE OIL LEVEL SENSOR

a.
A174870

Remove the 4 bolts and engine oil level sensor.


b.

Remove the gasket.


Hide 12102A 19.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

a.
A174871

Remove the 10 bolts and 2 nuts.


b.
A174872

Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.

NOTICE:

Be careful not to damage the contact surfaces of the No. 1 and No. 2 oil pans.



Hide 15104 20.REMOVE OIL STRAINER SUB-ASSEMBLY

a.
A174873

Remove the 2 bolts and oil strainer.


b.

Remove the O-ring from the oil strainer.


Hide 12101 21.REMOVE NO. 1 OIL PAN SUB-ASSEMBLY

a.
A174874E04
2.167,3.167 2.344,3.167 2.344,3.167 2.594,2.656 true 0.948,3.083 2.083,3.229 1.135,0.146 10 false Oil Reflector Plate

Remove the 20 bolts, 2 nuts and oil reflector plate.

NOTICE:

If the oil reflector plate is deformed, replace it.


HINT:

Be sure to clean the bolts and stud bolts, and check the threads for cracks or other damage.



b.
A177413

Remove the No. 1 oil pan by prying between the No. 1 oil pan and cylinder block with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block and oil pan.


HINT:

Tape the screwdriver tip before use.



c.
A174876

Remove the 3 O-rings.


d.
A179094

Remove the cylinder block oil hole gasket.


Hide 15310H 22.REMOVE OIL REGULATOR ASSEMBLY

a.
A161977

Remove the 4 bolts and oil regulator.


Hide 11381 23.REMOVE REAR ENGINE OIL SEAL RETAINER

a.
A161974

Remove the 10 bolts.


b.

Remove the oil seal retainer by prying between the oil seal retainer and cylinder block with a screwdriver.

HINT:

Tape the screwdriver tip before use.



Hide 15100 25.REMOVE OIL PUMP ASSEMBLY

a.
A161979

Remove the 4 bolts and oil pump.