Home › Engine / Hybrid System › 1UR-FE (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052776 1UR-FE ENGINE MECHANICAL _0255039 ENGINE ASSEMBLY A

1UR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 2. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 32917 5.REMOVE TRANSMISSION OIL COOLER AIR DUCT (w/ Air Cooled Transmission Oil Cooler)

Hide 53293C 6.REMOVE RADIATOR SIDE DEFLECTOR RH (w/o Air Cooled Transmission Oil Cooler)

Hide 53294C 7.REMOVE RADIATOR SIDE DEFLECTOR LH

Hide 53301 8.REMOVE HOOD SUB-ASSEMBLY

a.
A274179

Remove the 2 hood support bolts and disconnect the hood supports.

CAUTION:

Remove the hood support assembly while supporting the hood by hand.



b.

Remove the 4 bolts and hood.


Hide 55781E 9.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53783 10.REMOVE FRONT FENDER APRON TRIM PACKING B

Hide 53785B 11.REMOVE FRONT FENDER APRON TRIM PACKING D

Hide 53782 12.REMOVE FRONT FENDER APRON TRIM PACKING A

Hide 53784 13.REMOVE FRONT FENDER APRON TRIM PACKING C

Hide 51405A 14.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

a.
A178461

Remove the 10 bolts and No. 1 engine under cover sub-assembly.


Hide 51442 15.REMOVE NO. 2 ENGINE UNDER COVER

a.
A178462

Remove the 2 bolts and No. 2 engine under cover.


Hide 51440 16.REMOVE OIL PAN PROTECTOR ASSEMBLY

a.
C171483

Remove the 4 bolts and oil pan protector assembly.


Hide 28800 21.REMOVE BATTERY

a.

Remove the bolt and loosen the nut.


b.

Detach the hook of the battery clamp from the battery bracket, and then remove the battery clamp.


c.

Remove the battery.


Hide 16571C 23.REMOVE NO. 1 RADIATOR HOSE

Hide 16572D 25.REMOVE NO. 2 RADIATOR HOSE

Hide 17343 27.DISCONNECT NO. 3 AIR INJECTION SYSTEM HOSE (w/ Secondary Air Injection System)

a.
A218851

Disconnect the No. 3 air injection system hose from the air tube sub-assembly.


Hide 17361 31.REMOVE AIR TUBE SUB-ASSEMBLY (w/ Secondary Air Injection System)

Hide 11452 33.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 44410 35.DISCONNECT PRESSURE FEED TUBE

Hide 88320 38.DISCONNECT COOLER COMPRESSOR ASSEMBLY

Hide 89465 40.DISCONNECT HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)

Hide 89465 41.DISCONNECT HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)

Hide 17420 43.REMOVE CENTER EXHAUST PIPE ASSEMBLY

Hide 17450B 44.REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY

Hide 17410 45.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 17168 48.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17167 50.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 23271F 54.DISCONNECT FUEL HOSE AND FUEL TUBE SUB-ASSEMBLY

a.
A274180

Remove the fuel pipe clamp from the fuel tube connector.


b.

Disconnect the fuel hose and fuel tube sub-assembly (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 82121 55.DISCONNECT ENGINE WIRE

a.
A274181

Disconnect the clamp and ECM connector.

HINT:

Refer to the following procedures to disconnect the ECM connector (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>ECM>REMOVAL).



b.
A274182

Disconnect the 4 connectors and 2 clamps from the connector holder block.


c.
A274183

Remove the bolt and disconnect the ground wire.


d.
A274184

Remove the nut and disconnect the wire and 2 clips from the engine room junction block.


e.

Disconnect the 2 connectors and 2 clips from the engine room junction block.


f.

w/ Secondary Air Injection System:

Disconnect the 2 air injection control driver connectors.


g.

Remove the bolt, disconnect the clamp and ground wire.


h.

Remove the nut and disconnect the wire from the positive (+) battery cable.


i.
A218853

Disconnect the 2 connectors and 2 clips from the engine room junction block.


j.
A274394

w/ Secondary Air Injection System:

Disconnect the connector and clamp.


Hide 58.REMOVE FRONT PROPELLER SHAFT ASSEMBLY

Hide 16268 62.REMOVE NO. 1 WATER BY-PASS PIPE (w/ ATF Warmer)

a.
A274185

w/ Rear Heater:

Disconnect the 6 water hoses.


b.
A274186

Remove the 2 bolts and No. 1 water by-pass pipe.


c.
A274187

w/o Rear Heater:

Disconnect the 4 water hoses.


d.
A274188

Remove the 2 bolts and No. 1 water by-pass pipe.


Hide 87207A 63.REMOVE NO. 1 WATER BY-PASS PIPE (w/o ATF Warmer)

a.
A274189

Disconnect the hose.


b.

Remove the 2 bolts and No. 1 water by-pass pipe.


Hide 32101 65.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
A218920E01
0.456,2.963 0.771,3.110 0.316,0.147 10 SST 0.624,2.09 0.624,2.935 false 1.647,2.182 1.647,2.78 1.647,2.78 0.624,2.78 false 1.31,0.128 1.626,0.274 0.316,0.147 10 SST 1.68,0.206 1.792,0.206 1.792,0.206 2.239,0.632 false

Using SST, hold the crankshaft.

SST
09213-70011  (09213-70020)
09330-00021  


b.
A228359

Remove the 10 bolts, the rear drive plate spacer, the drive plate and ring gear, and the crankshaft angle sensor rotor.


Hide 12281A 66.INSTALL ENGINE HANGER

a.
A217476

Install 2 engine hangers with 2 bolts as shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
Engine Hanger 12281-38150
Bolt 90119-14120



Hide 67.REMOVE ENGINE ASSEMBLY

a.
A150148E02
0.096,0.562 0.280,0.716 0.185,0.155 10 *1 1.099,1.635 1.283,1.789 0.185,0.155 10 *2 1.096,0.563 1.281,0.718 0.185,0.155 10 *a 0.303,0.65 0.405,0.65 0.405,0.65 0.506,0.976 false 2.103,0.562 2.288,0.716 0.185,0.155 10 *1 2.09,0.65 1.988,0.65 1.988,0.65 1.886,0.976 false

Attach an engine sling device and hang the engine with a chain block.

Text in Illustration
*1 Engine Hanger
*2 Engine
*a 50° or less

NOTICE:

When hanging the engine, make sure to hang the engine with the angle of the sling device at 50° or less. Otherwise, the engine or engine hangers may be damaged.



b.
A218855E01
0.076,0.053 0.262,0.216 0.186,0.163 10 *A 0.076,2.453 0.262,2.616 0.186,0.163 10 *B

Remove the 2 nuts and 4 bolts from the front engine mounting insulator LH and RH.

Text in Illustration
*A for LH Side
*B for RH Side


c.

Lift the engine out of the vehicle carefully.

NOTICE:
·

Make sure the engine is clear of all wiring, hoses and cables.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.

·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.




d.

Remove the front engine mounting insulator LH and RH.


e.

Place the engine onto a workbench.


Hide 68.INSTALL ENGINE STAND

a.

Install the engine to an engine stand with bolts.


b.

Remove the 2 bolts and 2 engine hangers.


Hide 12362A 69.REMOVE FRONT ENGINE MOUNTING INSULATOR LH

a.
A218857

Remove the nut and mounting insulator.


Hide 12361 70.REMOVE FRONT ENGINE MOUNTING INSULATOR RH

a.
A218858

Remove the nut and mounting insulator.


Hide 12316A 71.REMOVE NO. 2 FRONT ENGINE MOUNTING BRACKET LH

a.
A178524

Remove the bolt and No. 2 front engine mounting bracket LH.