When replacing an injector (including interchanging injectors between cylinders) or common rail, replace the corresponding injection pipes with new ones.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Disconnect the cables from the negative (-) main battery and sub-battery terminals.
53806
3.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH
53805
4.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH
51405A
5.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
53292A
6.REMOVE UPPER RADIATOR SUPPORT SEAL
7.DRAIN ENGINE COOLANT
17940D
8.REMOVE INTERCOOLER ASSEMBLY (w/ Intercooler)
17973
9.REMOVE NO. 1 COOL AIR INLET (w/o Intercooler)
17973
10.REMOVE NO. 2 COOL AIR INLET (w/o Intercooler)
87209
11.DISCONNECT WATER HOSE SUB-ASSEMBLY
12.REMOVE NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE
17971
13.REMOVE AIR TUBE SUB-ASSEMBLY RH
14.REMOVE DIESEL THROTTLE BODY ASSEMBLY RH
15.DRAIN CLUTCH FLUID (for Manual Transmission)
31418
16.REMOVE CLUTCH HOSE (for Manual Transmission)
17972
17.REMOVE AIR TUBE SUB-ASSEMBLY LH
31489
18.REMOVE TUBE CONNECTOR TO FLEXIBLE HOSE TUBE (for Manual Transmission)
23265
19.REMOVE NO. 1 GAS FILTER
17947B
20.REMOVE NO. 3 INTERCOOLER SUPPORT BRACKET
26100G
21.REMOVE DIESEL THROTTLE BODY ASSEMBLY LH
17705
22.REMOVE AIR CLEANER CAP SUB-ASSEMBLY
17881
23.REMOVE NO. 1 AIR CLEANER HOSE
17861
24.REMOVE INTAKE AIR CONNECTOR
17363K
25.REMOVE NO. 3 AIR TUBE
17342D
26.REMOVE NO. 2 AIR HOSE
17364
27.REMOVE NO. 4 AIR TUBE
17806
28.REMOVE NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY
87208
29.REMOVE HEATER WATER PIPE SUB-ASSEMBLY (w/ Viscous Heater)
17885
30.REMOVE NO. 1 AIR CLEANER PIPE SUB-ASSEMBLY
23274D
31.DISCONNECT FUEL HOSE
16268M
32.REMOVE NO. 3 WATER BY-PASS PIPE (w/o Viscous Heater)
16288
33.REMOVE NO. 4 WATER BY-PASS PIPE
34.DISCONNECT ENGINE WIRE
23802E
35.REMOVE NO. 2 FUEL PIPE SUB-ASSEMBLY
23706
36.REMOVE NO. 6 INJECTION PIPE SUB-ASSEMBLY
23701
37.REMOVE INJECTION PIPE LH
23820A
38.REMOVE COMMON RAIL ASSEMBLY LH
23801L
39.REMOVE FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY
23702
40.REMOVE INJECTION PIPE RH
41.DISCONNECT NO. 2 ENGINE WIRE
25860
42.REMOVE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (for Engine Mounting)
Disconnect the 2 vacuum hoses.
Remove the bolt and vacuum switching valve.
25706
43.REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY
w/ Intercooler:
Disconnect the 2 vacuum hoses.
Remove the 3 bolts and vacuum transmitting pipe.
12263
44.REMOVE NO. 3 VENTILATION HOSE
11225
45.REMOVE CYLINDER HEAD COVER SILENCER LH (w/ Intercooler)
Remove the 3 bolts and cylinder head cover silencer.
23681E
46.REMOVE NOZZLE HOLDER SEAL LH
Using a small screwdriver, remove the 4 holder seals by prying the portion between each holder seal and the cutout part of the cylinder head cover.
Tape the screwdriver tip before use.
12270
47.REMOVE OIL SEPARATOR ASSEMBLY
Remove the 3 bolts, oil separator and gasket.
11202
48.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH
Remove the 17 bolts, cylinder head cover and gasket.
23682B
49.REMOVE NOZZLE HOLDER GASKET LH
Using a small screwdriver and hammer, remove the 4 nozzle holder gaskets.
Tape the screwdriver tip before use.
12262
50.REMOVE NO. 2 VENTILATION HOSE
11224
51.REMOVE CYLINDER HEAD COVER SILENCER RH (w/ Intercooler)
Remove the 3 bolts and cylinder head cover silencer.
23681D
52.REMOVE NOZZLE HOLDER SEAL RH
Using a small screwdriver, remove the 4 holder seals by prying the portion between each holder seal and the cutout part of the cylinder head cover.
Tape the screwdriver tip before use.
11201
53.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH
Remove the 18 bolts, cylinder head cover and gasket.
23682B
54.REMOVE NOZZLE HOLDER GASKET RH
Using a small screwdriver and hammer, remove the 4 nozzle holder gaskets.
Tape the screwdriver tip before use.
55.REMOVE FUEL INJECTOR RH
Remove the union bolt, 4 hollow screws, 5 gaskets and nozzle leakage pipe.
|
Union Bolt |
When removing the nozzle leakage pipe, place a cushion under the pipe.
Be careful not to deform or scratch the union seal surface.
After removing the nozzle leakage pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.
Remove the 4 bolts, 4 washers, 4 nozzle holder clamps and 4 injectors.
Arrange the injectors, holder clamps, washers and bolts in the correct order.
Remove the O-ring from each injector.
Remove the 4 injection nozzle seats from the cylinder head.
56.REMOVE FUEL INJECTOR LH
Remove the union bolt, 4 hollow screws, 5 gaskets and No. 2 nozzle leakage pipe.
|
Union Bolt |
When removing the nozzle leakage pipe, place a cushion under the pipe.
Be careful not to deform or scratch the union seal surface.
After removing the nozzle leakage pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.
Remove the 4 bolts, 4 washers, 4 nozzle holder clamps and 4 injectors.
Arrange the injectors, holder clamps, washers and bolts in the correct order.
Remove the O-ring from each injector.
Remove the 4 injection nozzle seats from the cylinder head.