Home › Engine / Hybrid System › 1VD-FTV (INTAKE / EXHAUST) › INTAKE MANIFOLD › from 2015.08
RM2660E _51 Engine / Hybrid System _052790 1VD-FTV INTAKE / EXHAUST _0255172 INTAKE MANIFOLD A

1VD-FTV INTAKE / EXHAUST  INTAKE MANIFOLD  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail, cylinder head, or intake manifold, it is necessary to replace the injection pipes with new ones.

·

w/ DPF:

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 53806 3.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Hide 53805 4.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Hide 51405A 5.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 53292A 6.REMOVE UPPER RADIATOR SUPPORT SEAL

Hide 17940D 8.REMOVE INTERCOOLER ASSEMBLY (w/ Intercooler)

Hide 17705 9.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

a.
A174698

Loosen the hose clamp.


b.

Disconnect the mass air flow meter connector and using a clip remover, detach the wire harness clamp from the air cleaner cap.


c.

Detach the 4 clamps and remove the air cleaner cap.


Hide 17881 10.REMOVE NO. 1 AIR CLEANER HOSE

a.
A174699

Loosen the hose clamp and remove the No. 1 air cleaner hose.


Hide 17861 11.REMOVE INTAKE AIR CONNECTOR

a.
A174749E06
0.802,2.813 0.927,2.813 0.927,2.813 1.25,2.448 true 0.563,2.729 0.75,2.885 0.188,0.156 10 false *A

w/ Viscous Heater:

Disconnect the 2 connectors from the viscous with magnet clutch heater and water temperature sensor.

Text in Illustration
*A w/ Viscous Heater


b.

w/o Viscous Heater:

Disconnect the connector from the water temperature sensor.


c.

Using a clip remover, detach the 3 wire harness clamps.


d.
A174710

Loosen the 2 hose clamps and remove the 2 bolts and intake air connector.


Hide 17973 12.REMOVE NO. 1 COOL AIR INLET (w/o Intercooler)

a.
A257026

Loosen the No. 1 air hose clamp.


b.

Disconnect the turbo pressure sensor connector, intake air temperature sensor connector and vacuum hose.


c.
A257028

Remove the 3 nuts, bolt and No. 1 cool air inlet.


d.

Remove the gasket from the air tube RH.


Hide 17973 13.REMOVE NO. 2 COOL AIR INLET (w/o Intercooler)

a.
A257027

Loosen the No. 2 air hose clamp.


b.
A257029

Remove the 3 nuts, bolt and No. 2 cool air inlet.


c.

Remove the gasket from the air tube LH.


Hide 14.REMOVE NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE

a.
A174875

Disconnect the wire harness clamp from the No. 2 engine oil level dipstick guide.


b.
A267228E01
0.136,0.056 0.321,0.211 0.185,0.155 10 *A 0.136,2.399 0.321,2.554 0.185,0.155 10 *B

Disconnect the ventilation hose from the cylinder head cover RH.

Text in Illustration
*A w/ DPF
*B w/o DPF


c.

Remove the 2 bolts and No. 2 engine oil level dipstick guide.


d.

Remove the O-ring from the No. 2 engine oil level dipstick guide.


Hide 17.DRAIN CLUTCH FLUID (for Manual Transmission)

Hide 31418 18.REMOVE CLUTCH HOSE (for Manual Transmission)

Hide 31489 20.REMOVE TUBE CONNECTOR TO FLEXIBLE HOSE TUBE (for Manual Transmission)

Hide 17947B 22.REMOVE NO. 3 INTERCOOLER SUPPORT BRACKET

Hide 26100G 23.REMOVE DIESEL THROTTLE BODY ASSEMBLY LH

Hide 17341F 24.REMOVE NO. 1 AIR HOSE

a.
A177374

Loosen the hose clamp and remove the No. 1 air hose.


Hide 17363K 25.REMOVE NO. 3 AIR TUBE

a.
A174751

Disconnect the wire harness from the clamp.


b.

Remove the nut and ground wire.


c.
A174752

Remove the bolt and disconnect the wire harness bracket.


d.
A174708

Loosen the hose clamp and remove the bolt and No. 3 air tube.


Hide 17342D 26.REMOVE NO. 2 AIR HOSE

a.
A177375

Loosen the hose clamp and remove the No. 2 air hose.


Hide 17364 27.REMOVE NO. 4 AIR TUBE

a.
A174690

Remove the bolt and disconnect the suction hose.


b.
A174706

Loosen the hose clamp and remove the bolt and No. 4 air tube.


Hide 17806 28.REMOVE NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY

a.
A174711

Disconnect the ventilation hose from the oil separator.


b.

Loosen the hose clamp.


c.

Remove the bolt and No. 2 air cleaner pipe.


Hide 87209 29.DISCONNECT WATER HOSE SUB-ASSEMBLY

A385826E01
0.344,0.323 0.656,0.521 0.313,0.198 10 false *A 3.573,0.333 3.885,0.531 0.313,0.198 10 false *B

Text in Illustration
*A w/ Rear Heater
*B w/o Rear Heater

Hide 87208 30.REMOVE HEATER WATER PIPE SUB-ASSEMBLY (w/ Viscous Heater)

a.
A174689

Remove the 4 bolts and disconnect the 4 water hose ends, and then remove the heater water pipe.


Hide 17885 31.REMOVE NO. 1 AIR CLEANER PIPE SUB-ASSEMBLY

a.
A174714

Loosen the hose clamp.


b.

Remove the bolt and No. 1 air cleaner pipe.


Hide 23274D 32.DISCONNECT FUEL HOSE

a.
A271646E02
0.125,0.125 0.406,0.344 0.281,0.219 10 true *a 0.125,2.563 0.458,2.823 0.333,0.26 10 true *b

w/ DPF:

Text in Illustration
*a for Fuel Filter with Heater
*b for Fuel Filter without Heater


b.
A271648E02
0.125,0.125 0.479,0.406 0.354,0.281 10 true *a 0.125,2.563 0.51,2.833 0.385,0.271 10 true *b

w/o DPF:

Text in Illustration
*a for Fuel Filter with Heater
*b for Fuel Filter without Heater


Hide 16268M 33.REMOVE NO. 3 WATER BY-PASS PIPE (w/o Viscous Heater)

a.
A174688

Remove the 2 bolts and disconnect the 2 water hose ends, and then remove the No. 3 water by-pass pipe.


Hide 16288 34.REMOVE NO. 4 WATER BY-PASS PIPE

a.

w/ EGR System:

i.

Remove the 2 bolts and nut.

A267344E01
0.203,0.084 0.388,0.238 0.185,0.155 10 *A 3.804,0.084 3.988,0.238 0.185,0.155 10 *B

Text in Illustration
*A w/ DPF *B w/o DPF


ii.

w/ DPF:

Disconnect the 3 water hose ends, and then remove the No. 4 water by-pass pipe.


iii.

w/o DPF:

Disconnect the 4 water hose ends, and then remove the No. 4 water by-pass pipe.



b.

w/o EGR System:

i.
A174692

Remove the 2 bolts and nut.


ii.

Disconnect the 3 water hose ends, and then remove the No. 4 water by-pass pipe.



Hide 35.DISCONNECT ENGINE WIRE

a.

LH Side:

i.
A174754

Disconnect the 4 connectors.


ii.

Using a clip remover, detach the 3 wire harness clamps.


iii.
A174755

Disconnect the 2 connectors.


iv.

Using a clip remover, detach the 3 wire harness clamps.


v.

Disconnect the 8 connectors.

U163560E03
1.083,1.51 1.208,1.656 0.125,0.146 10 false A 2.396,2.375 2.521,2.521 0.125,0.146 10 false B 6.417,1.26 6.542,1.406 0.125,0.146 10 false C 0.333,0.094 0.521,0.25 0.188,0.156 10 false *A 3.906,0.094 4.094,0.25 0.188,0.156 10 false *B 1.844,1.396 1.969,1.542 0.125,0.146 10 false A 4.563,1.563 4.688,1.708 0.125,0.146 10 false A 5.438,1.458 5.563,1.604 0.125,0.146 10 false A 6.073,2.479 6.198,2.625 0.125,0.146 10 false B 2.813,1.26 2.938,1.406 0.125,0.146 10 false C 4.885,1.875 5.01,2.021 0.125,0.146 10 false D 1.427,1.875 1.552,2.021 0.125,0.146 10 false D

Text in Illustration
*A w/ DPF *B w/o DPF


vi.

Remove the bolt and engine wire harness bracket labeled B.


vii.

Using a clip remover, detach the wire harness clamp labeled D.


viii.

Remove the 2 bolts and disconnect the engine wire protector labeled A.


ix.

for RHD:

Disconnect the wire harness from the wire harness clamp holder labeled C.



b.

RH Side:

i.

Disconnect the 7 connectors.

U163561E03
2.969,0.469 3.094,0.615 0.125,0.146 10 false A 6.854,1 6.979,1.146 0.125,0.146 10 false B 1.667,0.396 1.792,0.542 0.125,0.146 10 false C 0.177,0.063 0.365,0.219 0.188,0.156 10 false *A 3.771,0.063 3.958,0.219 0.188,0.156 10 false *B 1.438,1.427 1.563,1.573 0.125,0.146 10 false A 1.219,1.708 1.344,1.854 0.125,0.146 10 false A 4.833,1.813 4.958,1.958 0.125,0.146 10 false A 5.333,1.448 5.458,1.594 0.125,0.146 10 false A 6.063,0.969 6.188,1.115 0.125,0.146 10 false A 3.281,0.938 3.406,1.083 0.125,0.146 10 false B 5.104,0.625 5.229,0.771 0.125,0.146 10 false C

Text in Illustration
*A w/ DPF *B w/o DPF


ii.

Using a clip remover, detach the wire harness clamp.


iii.

Remove the 3 bolts and disconnect the wire harness protector labeled A.


iv.

Remove the bolt and wire harness bracket labeled B.


v.

Remove the screw grommet, nut and glow plug wire harness labeled C.


vi.
A267320E05
0.063,0.073 0.313,0.292 0.25,0.219 10 true *A 0.063,2.458 0.406,2.729 0.344,0.271 10 true *B

for RHD:

Disconnect the wire harness from the wire harness clamp holder.

Text in Illustration
*A w/ DPF
*B w/o DPF


vii.

for RHD:

Remove the bolt and wire harness clamp holder.



c.

Rear Side:

i.
U163811E02
0.458,1.917 0.583,2.063 0.125,0.146 10 false A 0.854,0.792 0.979,0.938 0.125,0.146 10 false B 1.885,0.208 2.01,0.354 0.125,0.146 10 false C 0.104,0.094 0.417,0.333 0.313,0.24 12 false *A 0.104,2.573 0.406,2.813 0.302,0.24 12 false *B 0.375,4.229 0.5,4.375 0.125,0.146 10 false A 2.896,0.813 3.021,0.958 0.125,0.146 10 false B 2.813,3.229 2.938,3.375 0.125,0.146 10 false B 0.875,3.26 1,3.406 0.125,0.146 10 false B 2.354,0.365 2.479,0.51 0.125,0.146 10 false C 1.615,2.708 1.74,2.854 0.125,0.146 10 false C 2.135,2.708 2.26,2.854 0.125,0.146 10 false C

Using a clip remover, detach the wire harness clamp.

Text in Illustration
*A w/ DPF
*B w/o DPF


ii.

Remove the 2 bolts and 2 ground wires labeled C.


iii.

Remove the 2 bolts and disconnect the engine wire harness protector labeled B.


iv.

w/ DPF:

Disconnect the 3 connectors.


v.

w/o DPF:

Disconnect the connector.


vi.

Remove the screw grommet, nut and disconnect the glow plug wire harness labeled A.



Hide 23802E 36.REMOVE NO. 2 FUEL PIPE SUB-ASSEMBLY (w/o DPF)

NOTICE:
·

After removing a fuel pipe, to prevent dirt or foreign objects from entering the fuel pipe ends, cover the fuel pipe ends with plastic bags.

·

After removing a fuel pipe, to prevent dirt or foreign objects from entering the fuel supply pump hole, cover the hole with protective tape.



a.
A174693

Disconnect the fuel hose from the No. 5 nozzle leakage pipe.


b.

Remove the bolt and No. 2 injection pipe clamp.


c.

Remove the union bolt and gasket.


d.

Remove the bolt, nut and No. 2 fuel pipe.


Hide 23706 37.REMOVE NO. 6 INJECTION PIPE SUB-ASSEMBLY

NOTICE:

After removing an injection pipe, to prevent dirt or foreign objects from entering the common rail holes, cover the holes with protective tape.


a.

w/ EGR System:

i.
A185542

Using a union nut wrench, loosen the No. 6 injection pipe ends.


ii.

Remove the 2 nuts and 2 No. 2 injection pipe clamps.


iii.

Remove the No. 6 injection pipe.



b.

w/o EGR System:

i.
A174695

Using a union nut wrench, loosen the No. 6 injection pipe ends.


ii.

Remove the nut and No. 2 injection pipe clamp.


iii.

Remove the bolt and No. 6 injection pipe.



Hide 25860 38.REMOVE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (w/ DPF)

Hide 25706 39.REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ DPF)

Hide 11225 40.REMOVE CYLINDER HEAD COVER SILENCER LH (w/ DPF)

Hide 23764A 41.REMOVE NO. 4 NOZZLE LEAKAGE PIPE (w/ DPF)

a.
A267230

Disconnect the fuel hose.


b.

Remove the fuel check valve, No. 4 nozzle leakage pipe and gasket.


Hide 23701 42.REMOVE INJECTION PIPE LH

a.
A267231E03
0.073,0.073 0.375,0.344 0.302,0.271 10 true *A 0.115,2.448 0.438,2.688 0.323,0.24 10 true *B

w/ Intercooler:

Remove the 2 nuts and 4 injection pipe clamps.

Text in Illustration
*A w/ DPF
*B w/o DPF


b.
A267232E03
0.052,0.063 0.344,0.302 0.292,0.24 10 true *A 0.052,2.396 0.365,2.635 0.313,0.24 10 true *B

Using a union nut wrench, remove the 4 injection pipes.

Text in Illustration
*A w/ DPF
*B w/o DPF

NOTICE:

After removing an injection pipe, to prevent dirt or foreign objects from entering the common rail holes or injector holes, cover the holes with protective tape.



Hide 23812D 43.REMOVE NO. 2 FUEL PIPE (w/ DPF)

Hide 23765 44.REMOVE NO. 5 NOZZLE LEAKAGE PIPE (w/ DPF)

Hide 23820A 45.REMOVE COMMON RAIL ASSEMBLY LH

Hide 23801L 46.REMOVE FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY

a.

w/ DPF:

i.
A267233

Remove the bolt and No. 2 injection pipe clamp.


ii.

Disconnect the fuel hose.


iii.

Remove the union bolt, nut, bolt, fuel filter to injection pump fuel pipe and gasket.



b.

w/o DPF:

i.
A174697

Disconnect the 2 hoses from the fuel pipe.


ii.

Remove the bolt and fuel filter to injection pump fuel pipe.



Hide 23243C 47.DISCONNECT FUEL PUMP MOTOR WIRE

a.
A174792

Remove the bolt and disconnect the connector from the fuel supply pump.


Hide 23705 48.REMOVE NO. 5 INJECTION PIPE SUB-ASSEMBLY

a.
A174696

Using a union nut wrench, remove the No. 5 injection pipe.

NOTICE:

After removing an injection pipe, to prevent dirt or foreign objects from entering the common rail hole or injection pump hole, cover the holes with protective tape.



Hide 11224 49.REMOVE CYLINDER HEAD COVER SILENCER RH (w/ DPF)

Hide 23712 50.REMOVE NO. 2 FUEL INJECTOR PROTECTOR (w/ DPF)

Hide 23711 51.REMOVE NO. 1 FUEL INJECTOR PROTECTOR (w/ DPF)

Hide 23702 52.REMOVE INJECTION PIPE RH

a.
A267234E03
0.073,0.083 0.427,0.396 0.354,0.313 10 true *A 0.073,2.51 0.385,2.75 0.313,0.24 10 true *B

w/ Intercooler:

Remove the 2 nuts and 4 injection pipe clamps.

Text in Illustration
*A w/ DPF
*B w/o DPF


b.
A267235E03
0.094,0.094 0.479,0.406 0.385,0.313 10 true *A 0.094,2.479 0.281,2.635 0.188,0.156 10 true *B

Using a union nut wrench, remove the 4 injection pipes.

Text in Illustration
*A w/ DPF
*B w/o DPF

NOTICE:

After removing an injection pipe, to prevent dirt or foreign objects from entering the common rail holes or injector holes, cover the holes with protective tape.



Hide 23810A 53.REMOVE COMMON RAIL ASSEMBLY RH

Hide 27148B 54.REMOVE CONNECTING WIRE (w/ DPF)

a.
A267236

Detach the 2 clamps and remove the connecting wire.


Hide 23763 55.REMOVE NO. 3 NOZZLE LEAKAGE PIPE (w/ DPF)

a.
A267237

Remove the 2 injector hollow screws, 3 bolts, No. 3 nozzle leakage pipe and 2 gaskets.


Hide 23762B 56.REMOVE NO. 2 NOZZLE LEAKAGE PIPE (w/ DPF)

Hide 23761A 57.REMOVE NO. 1 NOZZLE LEAKAGE PIPE (w/ DPF)

Hide 17135A 58.REMOVE NO. 1 INTAKE MANIFOLD INSULATOR (w/ Intercooler)

A174795

Hide 17136 59.REMOVE NO. 2 INTAKE MANIFOLD INSULATOR (w/ Intercooler)

A174791

Hide 17113 60.REMOVE INTAKE PIPE

a.
A174796

w/ EGR System:

Remove the 2 nuts, 6 bolts, intake pipe and 2 gaskets.


b.
A180252

w/o EGR System:

Remove the 2 nuts, 4 bolts, intake pipe and gasket.


Hide 61.DISCONNECT NO. 2 ENGINE WIRE

a.
A174797

Remove the 3 bolts and using a clip remover, detach the 2 wire harness clamps, and then disconnect the No. 2 engine wire.


Hide 17114D 62.REMOVE NO. 3 INTAKE MANIFOLD

a.
A174798

Remove the 16 bolts, No. 3 intake manifold and 2 gaskets.


Hide 17853B 63.REMOVE INTAKE MANIFOLD INSULATOR (w/ EGR System)

A174799

Hide 25615A 64.REMOVE EGR PIPE INSULATOR (w/ EGR System)

a.
A174800

Remove the 2 bolts and EGR pipe insulator.


Hide 25620 65.REMOVE EGR VALVE ASSEMBLY WITH EGR COOLER (w/ EGR System)

a.
A267242

Remove the 10 bolts, EGR valve with EGR cooler and 2 gaskets.


b.
A174802

Disconnect the No. 5 water by-pass hose from the water by-pass outlet.


Hide 25689 66.REMOVE EGR COOLER INSULATOR (w/ EGR System)

A174803

Hide 23763 67.REMOVE NO. 3 NOZZLE LEAKAGE PIPE (w/o DPF)

a.
A174804

Disconnect the No. 1 fuel hose from the fuel cooler.


b.

Remove the union bolt, bolt, No. 3 nozzle leakage pipe and gasket.

NOTICE:

After removing the nozzle leakage pipe, to prevent dirt or foreign objects from entering the nozzle leakage pipe, cover the nozzle leakage pipe ends with plastic bags.



Hide 23764A 68.REMOVE NO. 4 NOZZLE LEAKAGE PIPE (w/o DPF)

a.
A174805

Disconnect the No. 2 fuel hose from the fuel cooler.


b.

Remove the union bolt, bolt, No. 4 nozzle leakage pipe and gasket.

NOTICE:

After removing the nozzle leakage pipe, to prevent dirt or foreign objects from entering the nozzle leakage pipe, cover the nozzle leakage pipe ends with plastic bags.



Hide 16283 69.DISCONNECT NO. 6 WATER BY-PASS HOSE (w/o DPF)

A174806

Hide 23901H 71.REMOVE FUEL TUBE SUB-ASSEMBLY (w/ DPF)

a.
A267238

Disconnect the 3 fuel tube connectors (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL SYSTEM(w/ DPF)>PRECAUTION).


b.

Detach the 3 clamps and remove the fuel tube.


Hide 16268 72.REMOVE NO. 1 WATER BY-PASS PIPE

a.
A267239E04
0.094,0.083 0.365,0.302 0.271,0.219 10 true *A 0.094,2.438 0.385,2.656 0.292,0.219 10 true *B

Remove the union bolt, bolt, No. 1 water by-pass pipe and gasket.

Text in Illustration
*A w/ DPF
*B w/o DPF


Hide 23881D 73.REMOVE FUEL HOSE BRACKET (w/ DPF)

a.
A267240

Remove the bolt and fuel hose bracket.


Hide 23841C 74.REMOVE NO. 1 FUEL PIPE CLAMP (w/ DPF)

a.
A267241E03
0.083,0.083 0.375,0.333 0.292,0.25 10 true *a 0.083,2.521 0.271,2.677 0.188,0.156 10 false *b

Remove the 2 bolts and 2 No. 1 fuel pipe clamps.

Text in Illustration
*a RH Side
*b LH Side


Hide 17111 75.REMOVE NO. 1 INTAKE MANIFOLD

a.
A174809

Remove the 9 bolts, No. 1 intake manifold and gasket.


Hide 17112 76.REMOVE NO. 2 INTAKE MANIFOLD

a.
A174810

Remove the 9 bolts, No. 2 intake manifold and gasket.


Hide 77.REPLACE STUD BOLT

HINT:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A177310E04
1.917,2.354 3.094,2.531 1.177,0.177 10 false 20 mm (0.787 in.) 1.917,2.885 3.094,3.073 1.177,0.188 10 false 13 mm (0.512 in.) 0.333,2.521 0.948,2.875 0.615,0.354 10 false 42 mm (1.65 in.)

For Intake Pipe:

Using an E8 "TORX" wrench, replace the stud bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


b.

For No. 3 Intake Manifold:

A385827E01
1.469,1.24 1.688,1.24 1.688,1.24 1.688,1.521 false 1.24,1.583 1.51,1.583 false 2.542,1.26 1.938,1.26 1.938,1.26 1.938,1.479 false 2.323,1.698 2.323,1.26 true 1.906,1.958 1.719,1.969 1.719,1.969 1.719,2.198 true 1.313,1.198 1.594,1.385 0.281,0.188 10 false C 2.604,1.198 2.76,1.396 0.156,0.198 10 false A 1.094,1.49 1.25,1.688 0.156,0.198 10 false B 1.979,1.896 2.135,2.094 0.156,0.198 10 false B 4.927,0.344 5.083,0.542 0.156,0.198 10 false A 4.917,1.563 5.073,1.76 0.156,0.198 10 false B 4.917,2.385 5.198,2.573 0.281,0.188 10 false C 4.052,0.813 4.698,1.177 0.646,0.365 10 false 42 mm (1.65 in.) 5.333,0.792 6.542,0.99 1.208,0.198 10 false 20 mm (0.787 in.) 5.333,1.229 6.542,1.427 1.208,0.198 10 false 13 mm (0.512 in.) 5.313,1.885 6.521,2.083 1.208,0.198 10 false 9 mm (0.354 in.) 5.313,2.125 6.521,2.323 1.208,0.198 10 false 9 mm (0.354 in.) 5.333,2.771 6.542,2.969 1.208,0.198 10 false 21 mm (0.827 in.) 5.333,3.208 6.542,3.406 1.208,0.198 10 false 9 mm (0.354 in.) 4.063,1.854 4.708,2.219 0.646,0.365 10 false 24 mm (0.945 in.) 4.042,2.813 4.688,3.177 0.646,0.365 10 false 39 mm (1.54 in.)

i.

Using an E8 "TORX" wrench, replace the stud bolts labeled A.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


ii.

Using an E6 "TORX" wrench, replace the stud bolts labeled B.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


iii.

Using an E6 "TORX" wrench, replace the stud bolt labeled C.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)



Hide 78.REPLACE RING PIN

HINT:

It is not necessary to remove a ring pin unless it is being replaced.


a.
A177321E02
0.96,2.643 1.145,2.798 0.185,0.155 10 *1

For No. 1 and No. 2 Intake Manifold:

Replace the ring pins.

Standard protrusion:

4.4 to 5.6 mm (0.173 to 0.222 in.)


Text in Illustration
*1 Protrusion height