Wear protective gloves and protective glasses when installing the exhaust pipe.
The exhaust pipe is extremely hot immediately after the engine has stopped.
Confirm that the exhaust pipe has cooled down before removing it.
89425
1.INSTALL EXHAUST GAS TEMPERATURE SENSOR
89425A
2.INSTALL NO. 2 EXHAUST GAS TEMPERATURE SENSOR
89425B
3.INSTALL NO. 3 EXHAUST GAS TEMPERATURE SENSOR
18460
4.INSTALL MONOLITHIC CONVERTER ASSEMBLY LH
Install a new gasket to the turbocharger.
Make sure that the claw of the gasket faces downward.
Install the monolithic converter LH with 3 new nuts.
Temporarily install the No. 2 manifold stay with the 3 bolts.
Tighten the 2 bolts labeled A in the illustration first, and then tighten the bolt labeled B in the illustration.
Attach the 4 clamps and connect the 2 exhaust gas temperature sensor connectors.
| *1 | Tape |
Make sure that the tape is in the position shown in the illustration.
37140
5.INSTALL FRONT PROPELLER SHAFT ASSEMBLY
18450A
6.INSTALL MONOLITHIC CONVERTER ASSEMBLY RH
Install a new gasket to the turbocharger.
Make sure that the claw of the gasket faces the transmission.
Install the monolithic converter RH with 3 new nuts.
Temporarily install the manifold stay with the 3 bolts.
Tighten the 2 bolts labeled A in the illustration first, and then tighten the bolt labeled B in the illustration.
Attach the 4 clamps and connect the 2 exhaust gas temperature sensor connectors.
89425C
7.INSTALL NO. 4 EXHAUST GAS TEMPERATURE SENSOR
17450B
8.INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY
Install a new gasket and the front No. 2 exhaust pipe to the monolithic converter LH with 3 new nuts.
Attach the clamp and connect the exhaust gas temperature sensor connector.
| *1 | Tape |
| *2 | Stopper |
| *3 | Clip |
| *a | 2 to 7 mm (0.0787 to 0.276 in.) |
|
Paint Mark |
Make sure that the tape is in the position shown in the illustration.
Install 2 new clips to the 2 air hoses.
Connect the 2 air hoses to the front No. 2 exhaust pipe.
Align the paint marks of the front No. 2 exhaust pipe and air hose and push on the air hose until it contacts the stopper.
Make sure the clip is 4 to 10 mm (0.157 to 0.394 in.) from the end of the air hose when installing the clip.
Make sure that there is no slack in the air hose, and that it is not twisted or bent.
Take care not to damage the inner or outer surface of the air hose when installing it. If the air hose is damaged, replace it with a new one.
17450
9.INSTALL NO. 5 EXHAUST PIPE ASSEMBLY
Install a new gasket and the No. 5 exhaust pipe to the front No. 2 exhaust pipe with 2 new nuts.
17410
10.INSTALL FRONT EXHAUST PIPE ASSEMBLY
Install a new gasket and the front exhaust pipe to the monolithic converter RH with 3 new nuts.
Attach the clamp and connect the exhaust gas temperature sensor connector.
| *1 | Tape |
| *2 | Stopper |
| *3 | Clip |
| *a | 2 to 7 mm (0.0787 to 0.276 in.) |
|
Paint Mark |
Make sure that the tape is in the position shown in the illustration.
Install 2 new clips to the 2 air hoses.
Connect the 2 air hoses to the front exhaust pipe assembly, and slide the 2 clamps to secure the hose.
Align the paint marks of the front exhaust pipe and air hose and push on the air hose until it contacts the stopper.
Make sure the clip is 4 to 10 mm (0.157 to 0.394 in.) from the end of the air hose when installing the clip.
Make sure that there is no slack in the air hose, and that it is not twisted or bent.
Take care not to damage the inner or outer surface of the air hose when installing it. If the air hose is damaged, replace it with a new one.
51440
11.INSTALL OIL PAN PROTECTOR ASSEMBLY RH (for 2-piece Type)
51440
12.INSTALL OIL PAN PROTECTOR ASSEMBLY LH (for 2-piece Type)
51440
13.INSTALL OIL PAN PROTECTOR ASSEMBLY (for 1-piece Type)
17420
14.INSTALL CENTER EXHAUST PIPE ASSEMBLY
Check the free length.
Using a vernier caliper, measure the free length of the compression spring.
43 mm (1.69 in.)
If the free length is less than the minimum, replace the compression spring.
Connect the center exhaust pipe to the 3 exhaust pipe supports.
Install 2 new gaskets to the No. 5 exhaust pipe and front exhaust pipe.
Install the center exhaust pipe with the 4 bolts and 2 compression springs.
17430
15.INSTALL TAILPIPE ASSEMBLY
Connect the tailpipe to the 2 exhaust pipe supports.
| *1 | Gasket |
| *a | Top |
| *b | LH Side |
|
Front |
Install a new gasket to the center exhaust pipe.
Connect the tailpipe to the center exhaust pipe with a new clamp.
Install the clamp within the angle range shown in the illustration.
Tighten the bolt.
89467B
16.INSTALL AIR FUEL RATIO SENSOR
17.INSPECT FOR EXHAUST GAS LEAK
51442
18.INSTALL NO. 2 ENGINE UNDER COVER
Install the No. 2 engine under cover with the 6 bolts.
53785B
19.INSTALL FRONT FENDER APRON SEAL REAR LH
53784
20.INSTALL FRONT FENDER APRON SEAL REAR RH
21.PERFORM CATALYST RECORD OF DPF THERMAL DETERIORATION CLEAR FUNCTION