Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION ASSEMBLY (for 1VD-FTV) › from 2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255267 AUTOMATIC TRANSMISSION ASSEMBLY(for 1VD-FTV) A

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY(for 1VD-FTV)  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

The automatic transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop.


PROCEDURE

Hide 32000 1.INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY

a.
U164923E02
2.406,1.635 2.531,1.792 0.125,0.156 10 false A 3.083,1.094 3.271,1.271 0.188,0.177 10 false *a 2.938,1.583 3.125,1.76 0.188,0.177 10 true *b

Using a vernier caliper and straightedge, measure the dimension (A) between the automatic transmission assembly contact surface of the engine assembly (*b) and the torque converter assembly contact surface of the drive plate (*a).

Text in Illustration
*a Drive Plate Surface
*b Engine Assembly Surface


b.
C337055E01
0.401,0.079 0.590,0.269 0.188,0.191 10 *a 1.084,0.181 0.629,0.193 0.629,0.193 1.129,0.602 false

Align the matchmark on the automatic transmission case sub-assembly with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.

Text in Illustration
*a Matchmark

NOTICE:

Install the torque converter assembly to the input shaft while keeping it horizontal.



c.
C337056E02
2.948,0.792 3.052,0.333 3.052,0.333 3.125,0.333 true 2.938,1.208 3.042,1.635 3.042,1.635 3.104,1.635 true 3.115,0.25 3.292,0.438 0.177,0.188 10 true *1 3.104,1.552 3.281,1.74 0.177,0.188 10 true *1

Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.

Text in Illustration
*1 Front Oil Pump Oil Seal

NOTICE:
·

Do not damage the front oil pump oil seal.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.




d.
C337057E02
2.938,0.802 3.042,0.344 3.042,0.344 3.115,0.344 true 2.948,1.198 3.042,1.635 3.042,1.635 3.104,1.635 true 3.115,0.24 3.292,0.427 0.177,0.188 10 true *1 3.115,1.542 3.292,1.729 0.177,0.188 10 true *1

Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the automatic transmission case sub-assembly and insert the key of the torque converter assembly into the groove of the oil pump drive gear.

Text in Illustration
*1 Front Oil Pump Oil Seal

NOTICE:
·

Do not push the torque converter assembly excessively when rotating it.

·

Do not damage the front oil pump oil seal.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.




e.
C161370E03
2.997,1.629 3.128,1.809 0.131,0.179 10 B

Using a vernier caliper and straightedge, measure the dimension (B) shown in the illustration and check that the dimension (B) is more than the dimension (A), which was measured in the previous step.

Standard distance:

B = A + 1.00 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the automatic transmission assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.




Hide 36179 3.REMOVE LOWER TRANSFER CASE PROTECTOR

a.

Install the lower transfer case protector with the 7 bolts and attach the clamp.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 35000 4.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY

a.
C274145E01
0.837,0.914 0.993,1.096 0.156,0.181 10 *1 2.309,1.356 2.465,1.537 0.156,0.181 10 *2 1.396,1.006 1.039,1.006 false 1.758,1.113 2.1,1.455 2.1,1.455 2.258,1.455 false

Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

Text in Illustration
*1 Crankshaft
*2 Torque Converter Assembly Centerpiece
V100135

Clutch Spline Grease

Clutch spline grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum grease amount:

Approximately 1 g (0.0353 oz.)



b.

Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.


c.
U164816E02
2.563,0.031 2.698,0.188 0.135,0.156 10 false A 1.094,0.031 1.229,0.188 0.135,0.156 10 false A 0.698,0.49 0.833,0.646 0.135,0.156 10 false A 2.979,0.479 3.115,0.635 0.135,0.156 10 false A 3.063,1.24 3.198,1.396 0.135,0.156 10 false A 2.938,1.542 3.073,1.698 0.135,0.156 10 false A 0.604,1.229 0.74,1.385 0.135,0.156 10 false A 0.708,1.542 0.844,1.698 0.135,0.156 10 false A 1.104,1.969 1.229,2.125 0.125,0.156 10 false B 2.563,1.854 2.688,2.01 0.125,0.156 10 false B

While keeping the engine assembly and automatic transmission assembly horizontal, align the 2 knock pins with the holes in the automatic transmission assembly and install the 10 bolts.

Torque:
for 17 mm head bolt A : 71 N*m (724 kgf*cm, 52 ft.*lbf)
for 14 mm head bolt B : 37 N*m (377 kgf*cm, 27 ft.*lbf)

NOTICE:
·

Do not use excessive force when installing the automatic transmission assembly.

·

Check that the torque converter assembly rotates.

·

Make sure that the wire harness or other similar items are not pinched between the contact surfaces.

·

Make sure that the cooling fan and fan shroud do not contact the engine assembly when tilting the automatic transmission assembly.




Hide 35119A 5.INSTALL TRANSMISSION HOUSING COVER

C175581

a.

Install the transmission housing cover with the 3 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 12140 6.INSTALL OIL PAN COVER

C172394

a.

Install the oil pan cover with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 7.CONNECT WIRE HARNESS AND CONNECTOR

U164681

a.

Connect the park/neutral position switch connector, 2 transmission wire connectors, 2 speed sensor connectors and 2 or 3 transfer control side connectors.

HINT:

Push up the lever until the claw of the transmission wire connector makes a connection sound.



b.

Connect the 8 harness clamps.


c.

Connect the wire harness with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


d.

Tilt up the automatic transmission.


Hide 35104V 8.CONNECT BREATHER PLUG HOSE

C171532

a.

Connect the 3 breather plug hoses to the wire harness.


Hide 12371 9.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

C172398

a.

Install the rear No. 1 engine mounting insulator to the automatic transmission assembly with the 4 bolts.

Torque:
59 N*m (602 kgf*cm, 44 ft.*lbf)


Hide 51203 10.INSTALL NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY

a.
C171489

Install the No. 2 frame crossmember sub-assembly to the rear No. 1 engine mounting insulator with the 4 bolts.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


b.
U164644

Install the No. 2 frame crossmember sub-assembly to the frame with the 4 bolts and 4 nuts.

Torque:
110 N*m (1122 kgf*cm, 81 ft.*lbf)


c.
C171484

Install the engine mounting hole cover.


Hide 11.CONNECT GROUND CABLE

a.
C171503

Connect the ground cable with the bolt.

Torque:
for Type A : 8.4 N*m (86 kgf*cm, 74 in.*lbf)
for Type B : 10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:
A418191C01
0.375,0.219 0.688,0.375 0.313,0.156 10 false *A 2.135,0.219 2.448,0.375 0.313,0.156 10 false *B
*A for Type A
*B for Type B


Type A or B can be distinguished by confirming the mark on the bolt.



Hide 32907A 12.CONNECT OIL COOLER TUBE

a.
U164823E02
1.094,2.094 0.854,2.24 false 1.104,1.979 1.281,2.135 0.177,0.156 10 false *a 0.49,2.927 0.656,3.094 0.167,0.167 10 false *b 0.396,2.417 0.646,2.615 0.25,0.198 10 false 45° 0.396,2.667 0.646,2.865 0.25,0.198 10 false 45° 3.167,0.979 3.302,1.135 0.135,0.156 10 false A 0.969,0.667 1.094,0.823 0.125,0.156 10 false B 1.177,1.719 1.302,1.875 0.125,0.156 10 false C

Connect the 2 transmission oil cooler hoses as shown in the illustration.

Text in Illustration
*a Paint Mark
*b RH Side

NOTICE:
·

Make sure the pinching portion of each clip is facing the direction shown in the illustration.

·

Make sure the paint mark of each hose is facing outward.




b.

Temporarily install the oil cooler tube to the engine with the bolts A and B. Install the bolt C and tighten it to the specified torque. Then tighten the bolts A and B to the specified torque.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 32101A 13.INSTALL DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT

C171531

a.

Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter setting bolts and install each bolt while holding the crankshaft pulley set bolt with a wrench.

Torque:
53 N*m (540 kgf*cm, 39 ft.*lbf)

NOTICE:

First install the black colored bolt and then install the remaining 5 bolts.



b.
A170323

Install the oil pan insulator with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 37110 16.INSTALL PROPELLER SHAFT ASSEMBLY

Hide 37140 17.INSTALL FRONT PROPELLER SHAFT ASSEMBLY

Hide 33702B 18.CONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY

C170828

a.

Connect the gear shifting rod to the transmission control shaft lever RH with the pin and a new clip.


Hide 19.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 21.INSPECT SHIFT LEVER POSITION

a.

When moving the shift lever from P to R with the ignition switch ON and the brake pedal depressed, make sure that it moves smoothly and correctly into position.


b.

Check that the shift lever does not stop when moving the shift lever from R to P, and check that the shift lever does not stick when moving the shift lever from D to S.


c.

Start the engine and make sure that the vehicle moves forward after moving the shift lever from N to D and moves rearward after moving the shift lever to R.

If there are problems during the above inspections, perform the adjustment using the following procedures.

i.

Move the shift lever to N


ii.
C337021E01
1.417,0.16 1.617,0.359 0.200,0.199 10 *a 2.424,0.261 1.647,0.261 false

Loosen the nut of the floor shift gear shifting rod. Then, with the lever of the floor shift assembly lightly pushed towards the rear of the vehicle, tighten the nut.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)

Text in Illustration
*a Lever
V100135

Nut
V100136

Push



Hide 22.INSPECT FOR EXHAUST GAS LEAK

Hide 51440 23.INSTALL OIL PAN PROTECTOR ASSEMBLY RH (w/ DPF)

a.
A362372

Install the oil pan protector assembly RH with the 4 bolts.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


Hide 51440 24.INSTALL OIL PAN PROTECTOR ASSEMBLY LH (w/ DPF)

a.
A362371

Install the oil pan protector assembly LH with the 6 bolts.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


Hide 51440 25.INSTALL OIL PAN PROTECTOR ASSEMBLY (w/o DPF)

C171483

a.

Install the oil pan protector assembly with the 4 bolts.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


Hide 51405A 29.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 53806 30.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Hide 53805 31.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH