Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255251 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Cruise Control Switch Circuit  


DESCRIPTION

The cruise control main switch is used to turn the dynamic radar cruise control system on and off, as well as operate 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP and CANCEL. The SET, TAP-DOWN and - (COAST) functions, and the RES (RESUME), TAP-UP and + (ACCEL) functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only while operating it in the direction of each arrow and turns off after releasing it. The internal contact points of the cruise control main switch turn on with switch operation. Then the ECM reads the voltage value that has been changed by the switch operation to control the SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL functions.

WIRING DIAGRAM

C349536E03
2.505,1.991 2.841,2.550 0.336,0.559 10 ON-OFF 1.865,1.991 2.500,2.196 0.635,0.205 10 +RES 1.267,1.991 1.895,2.272 0.628,0.281 10 -SET 0.494,1.991 1.129,2.182 0.635,0.191 10 CANCEL 4.618,2.573 5.107,2.793 0.489,0.221 10 E112 4.618,1.669 5.107,1.890 0.489,0.221 10 E112 4.12,1.525 4.505,1.702 0.385,0.177 10 CCS 4.12,2.412 4.568,2.623 0.448,0.211 10 ECC 3.871,3.049 5.061,3.747 1.191,0.698 10 Spiral Cable Sub-assembly 3.65,1.663 3.993,1.881 0.343,0.218 10 z37 3.65,2.567 3.993,2.785 0.343,0.218 10 z37 0.069,3.88 2.510,4.224 2.441,0.343 10 *1: Cruise Control Switch Wire 3.177,2.783 3.625,3.126 0.448,0.343 10 *1 0.662,3.238 2.443,3.568 1.781,0.330 10 Cruise Control Main Switch 6.344,2.573 6.888,2.805 0.545,0.232 10 ECCS*2 5.977,2.556 6.376,2.906 0.399,0.350 10 A38 6.021,2.324 6.247,2.487 0.225,0.163 10 59 6.33,0.478 6.756,0.634 0.427,0.156 10 CSS 5.964,0.478 6.239,0.664 0.275,0.186 10 A38 6.007,0.229 6.267,0.385 0.260,0.156 10 60 5.607,0.478 5.903,0.664 0.296,0.186 10 A38 5.296,0.229 5.515,0.385 0.218,0.156 10 45 5.662,0.229 5.881,0.385 0.218,0.156 10 40 4.88,0.478 5.174,0.662 0.295,0.184 10 A52 5.236,0.478 5.525,0.664 0.289,0.186 10 A38 4.515,0.478 4.810,0.662 0.295,0.184 10 A52 4.93,0.229 5.149,0.385 0.218,0.156 10 40 4.564,0.229 4.783,0.385 0.218,0.156 10 45 0.069,4.247 1.096,4.421 1.026,0.174 10 *2: for 3UR-FE 6.028,0.705 6.212,0.870 0.184,0.165 10 *2 6.005,2.802 6.272,3.022 0.267,0.221 10 *2 0.069,4.61 2.003,4.822 1.934,0.211 10 *3: except 3UR-FE 6.505,3.852 7.096,4.045 0.591,0.193 10 ECM 5.496,2.965 5.874,3.232 0.378,0.267 10 *3 5.646,0.705 5.811,0.861 0.165,0.156 10 *4 0.069,4.974 1.670,5.158 1.600,0.184 10 *4: for 1VD-FTV (LHD) 5.272,0.705 5.465,0.879 0.192,0.174 10 *5 0.069,5.337 2.746,5.521 2.677,0.184 10 *5: for 1UR-FE (LHD) 4.922,0.705 5.096,0.879 0.174,0.174 10 *6 2.974,3.908 5.815,4.083 2.841,0.174 10 *6: for 1VD-FTV (RHD) 4.571,0.705 4.857,0.916 0.286,0.211 10 *7 2.974,4.275 5.709,4.431 2.735,0.156 10 *7: for 1UR-FE (RHD) 0.662,3.077 0.777,3.233 0.114,0.156 10 A 4.746,1.417 4.965,1.566 0.218,0.149 10 1 4.746,2.321 4.958,2.490 0.211,0.170 10 2 3.717,1.417 3.901,1.566 0.184,0.149 10 3 2.945,1.529 3.129,1.678 0.184,0.149 10 3 2.945,2.426 3.163,2.575 0.218,0.149 10 1 3.717,2.321 3.838,2.469 0.121,0.149 10 4

PROCEDURE

1.READ VALUE USING GTS (CRUISE CONTROL MAIN SWITCH)
a.

Use the Data List to check if the cruise control main switch is functioning properly (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

Cruise Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Cancel Switch CANCEL switch status / ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
-SET Switch -/SET switch status / ON or OFF ON: -/SET switch on
OFF: -/SET switch off
-
+RES Switch +/RES switch status / ON or OFF ON: +/RES switch on
OFF: +/RES switch off
-
Cruise Ready Main-CPU Cruise control system standby condition / ON or OFF Each time cruise control main switch (ON/OFF) is pushed, ON or OFF changes -
Cruise Ready Sub-CPU Cruise control system standby condition / ON or OFF Each time cruise control main switch (ON/OFF) is pushed, ON or OFF changes -

OK:

The Data List items shown in the table change according to the operation of the cruise control main switch.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT CRUISE CONTROL SWITCH
2.INSPECT CRUISE CONTROL SWITCH
a.

Remove the cruise control main switch (See page Engine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>REMOVAL).


b.

Inspect the cruise control main switch (See page Engine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>INSPECTION).



OK

3.INSPECT CRUISE CONTROL SWITCH WIRE

NG

3.INSPECT CRUISE CONTROL SWITCH WIRE
U163749E01
0.371,0.404 0.735,0.691 0.364,0.288 10 *a 0.371,2.747 0.735,3.035 0.364,0.288 10 *b 1.127,1.581 0.62,2.088 false 1.067,3.815 0.56,4.322 false 1.368,1.581 1.875,2.088 false 1.525,3.815 2.032,4.322 false 0.206,2.019 0.668,2.189 0.461,0.170 10 CCS 2.081,4.254 2.543,4.423 0.461,0.170 10 CCS 1.944,2.019 2.406,2.189 0.461,0.170 10 ECC 0.157,4.254 0.618,4.423 0.461,0.170 10 ECC 1.094,0.352 1.417,0.494 0.323,0.142 10 z37 1.222,2.625 1.336,2.774 0.114,0.149 10 A

a.

Disconnect the z37 spiral cable sub-assembly connector.


b.

Disconnect the A cruise control main switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z37-3 (CCS) - A-3 (CCS) Always Below 1 Ω
z37-4 (ECC) - A-1 (ECC)
z37-3 (CCS) - Body ground Always 10 kΩ or higher
z37-4 (ECC) - Body ground


Text in Illustration
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)
*b Front view of wire harness connector
(to Cruise Control Main Switch)



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).


b.

Inspect the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION).



OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)
a.

Disconnect the E112 spiral cable sub-assembly connector.


b.

Disconnect the A38*1 or A52*2 ECM connector.

*1: for 3UR-FE, 1VD-FTV (LHD )and 1UR-FE (LHD)

*2: for 1UR-FE (RHD), 1GR-FE (RHD) and 1VD-FTV (RHD)



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E112-1 (CCS) - A38-60 (CCS)*1 Always Below 1 Ω
E112-1 (CCS) - A38-40 (CCS)*2
E112-1 (CCS) - A38-45 (CCS)*3
E112-1 (CCS) - A52-40 (CCS)*4
E112-1 (CCS) - A52-45 (CCS)*5
E112-2 (ECC) - Body ground
E112-1 (CCS) or A38-60 (CCS)*1 - Body ground Always 10 kΩ or higher
E112-1 (CCS) or A38-40 (CCS)*2 - Body ground
E112-1 (CCS) or A38-45 (CCS)*3 - Body ground
E112-1 (CCS) or A52-40 (CCS)*4 - Body ground
E112-1 (CCS) or A52-45 (CCS)*5 - Body ground


*1: for 3UR-FE

*2: for 1VD-FTV (LHD)

*3: for 1UR-FE (LHD)

*4: for 1VD-FTV (RHD)

*5: for 1UR-FE (RHD)


Result
Result Proceed to
OK (for 1UR-FE) A
OK (for 3UR-FE) B
OK (for 1VD-FTV) C
NG D



A

B

C

D

REPAIR OR REPLACE HARNESS OR CONNECTOR