32910
1.INSTALL OIL COOLER ASSEMBLY
Connect the oil cooler inlet hose and outlet hose.
| *a | Lower Side |
| *b | Outward |
Install the rear transmission oil cooler air duct with the 4 bolts, and then install the air cooled oil cooler tube to the transmission oil cooler air duct with the bolt.
Temporarily put the oil cooler on the radiator support.
Securely attach the 2 claws of the oil cooler into the holes of the radiator support.
| *1 | Claw |
Install the 4 bolts in the sequence shown in the illustration.
32917
2.INSTALL TRANSMISSION OIL COOLER AIR DUCT
Install the oil cooler air duct with the 4 bolts.
32907A
3.INSTALL OIL COOLER TUBE
| *A | for 1VD-FTV | *B | for 1UR-FE, 3UR-FE |
Temporarily install the oil cooler tube to the fan shroud with bolt A. Install bolt B and tighten it to the specified torque. Then tighten bolt A to the specified torque.
32907A
4.INSTALL OIL COOLER TUBE (w/o Air Cooled Transmission Oil Cooler)
Temporarily install the oil cooler tube to the fan shroud with bolt A. Install bolt B and tighten it to the specified torque. Then tighten bolt A to the specified torque.
32941H
5.CONNECT INLET NO. 4 OIL COOLER HOSE
Connect the inlet oil cooler hose as shown in the illustration.
Make sure the pinching portion of each clip is facing the direction shown in the illustration and the paint marks are aligned as shown in the illustration.
| *1 | Paint Mark |
32942
6.CONNECT INLET NO. 2 OIL COOLER HOSE AND INLET NO. 3 OIL COOLER HOSE
| *A | for 1VD-FTV | *B | for 1UR-FE, 3UR-FE |
Connect the 2 inlet oil cooler hoses as shown in the illustration.
Make sure the pinching portion of each clip is facing the direction shown in the illustration.
32942
7.CONNECT INLET NO. 2 OIL COOLER HOSE AND INLET NO. 3 OIL COOLER HOSE (w/o Air Cooled Transmission Oil Cooler)
Connect the 2 inlet oil cooler hoses as shown in the illustration.
Make sure the pinching portion of each clip is facing the direction shown in the illustration.
32942
8.CONNECT INLET NO. 1 OIL COOLER HOSE AND OUTLET NO. 1 OIL COOLER HOSE
| *A | for 1VD-FTV | *B | for 1UR-FE, 3UR-FE |
| *1 | Paint Mark | - | - |
Connect the 2 oil cooler hoses as shown in the illustration.
Make sure the pinching portion of each clip is facing the direction shown in the illustration and the paint marks are aligned as shown in the illustration.
Attach the hose to the flexible hose clamp and close the clamp as shown in the illustration.
32942
9.CONNECT INLET NO. 1 OIL COOLER HOSE AND OUTLET NO. 1 OIL COOLER HOSE (w/o Air Cooled Transmission Oil Cooler)
Connect the 2 oil cooler hoses as shown in the illustration.
| *1 | Paint Mark |
Make sure the pinching portion of each clip is facing the direction shown in the illustration and the paint marks are aligned as shown in the illustration.
32943B
10.CONNECT TRANSMISSION OIL COOLER HOSE
Connect the 2 transmission oil cooler hoses as shown in the illustration.
| *a | RH Side |
| *b | Paint Mark |
Make sure the pinching portion of each clip is facing the direction shown in the illustration.
Make sure the paint mark of each hose is facing outward.
11.ADD AUTOMATIC TRANSMISSION FLUID
Add automatic transmission fluid (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION FLUID>ADJUSTMENT).
52119A
12.INSTALL FRONT BUMPER COVER (w/ Air Cooled Transmission Oil Cooler)
for Standard:
(See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER(for Standard)>INSTALLATION)
w/ Winch:
(See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER(w/ Winch)>INSTALLATION)
51442
13.INSTALL NO. 2 ENGINE UNDER COVER
51405A
14.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
53806
15.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH
53805
16.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH
53784
17.INSTALL FRONT FENDER APRON TRIM PACKING C
53782
18.INSTALL FRONT FENDER APRON TRIM PACKING A