Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION ASSEMBLY (for 1VD-FTV) › from 2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255267 AUTOMATIC TRANSMISSION ASSEMBLY(for 1VD-FTV) A

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY(for 1VD-FTV)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 53806 3.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Hide 53805 4.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Hide 51405A 5.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 51440 7.REMOVE OIL PAN PROTECTOR ASSEMBLY (w/o DPF)

a.
C171483

Remove the 4 bolts and oil pan protector assembly.


Hide 51440 8.REMOVE OIL PAN PROTECTOR ASSEMBLY LH (w/ DPF)

a.
A362371

Remove the 6 bolts and oil pan protector assembly LH.


Hide 51440 9.REMOVE OIL PAN PROTECTOR ASSEMBLY RH (w/ DPF)

a.
A362372

Remove the 4 bolts and oil pan protector assembly RH.


Hide 53782 10.REMOVE FRONT FENDER APRON TRIM PACKING A

Hide 53784 11.REMOVE FRONT FENDER APRON TRIM PACKING C

Hide 33702B 13.DISCONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY

C170828

a.

Remove the clip and pin, and disconnect the gear shifting rod from the transmission control shaft lever RH.


Hide 37140 14.REMOVE FRONT PROPELLER SHAFT ASSEMBLY

Hide 37110 15.REMOVE PROPELLER SHAFT ASSEMBLY

Hide 32101A 18.REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT

a.
A170323

Remove the 2 bolts and oil pan insulator.


b.
A185177

Using a wrench, hold the crankshaft.

NOTICE:

Do not turn the crankshaft counterclockwise. If it is turned counterclockwise, check that the crankshaft pulley set bolt is not loose. If loose, tighten the bolt (See page Engine / Hybrid System>1VD-FTV (LUBRICATION)>OIL PUMP>INSTALLATION).



c.
C171531

Remove the 6 drive plate and torque converter setting bolts.

HINT:

There will be one black colored bolt.



Hide 32907A 19.DISCONNECT OIL COOLER TUBE

C177423

a.

Disconnect the 2 transmission oil cooler hoses from the oil cooler tube union.


b.

Remove the 3 bolts and separate the oil cooler tube from the engine.


Hide 20.DISCONNECT GROUND CABLE

a.
C171503

Remove the bolt and disconnect the ground cable.


Hide 35000 21.SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

a.
C161356

Support the transmission with a transmission jack. Lift the transmission slightly from the crossmember.

NOTICE:
·

In order to protect the automatic transmission oil pan sub-assembly, place attachments on the transmission jack.

·

Make sure that the attachments and the automatic transmission oil pan sub-assembly are centered on the transmission jack.

·

To prevent the automatic transmission oil pan sub-assembly from deforming, do not place any attachments under the automatic transmission oil pan sub-assembly of the automatic transmission assembly.

·

Secure the automatic transmission assembly to the transmission jack using a belt, etc. to prevent it from falling.




Hide 51203 22.REMOVE NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY

C171484

a.

Remove the engine mounting hole cover.


b.
C171489

Remove the 4 bolts of the rear No. 1 engine mounting insulator.


c.
U164644

Remove the 4 nuts, 4 bolts and No. 2 frame crossmember sub-assembly.


Hide 12371 23.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

a.
C172398

Remove the 4 bolts and rear No. 1 engine mounting insulator from the automatic transmission assembly.


Hide 35104V 24.DISCONNECT BREATHER PLUG HOSE

C171532

a.

Disconnect the 3 breather plug hoses from the wire harness.


Hide 25.DISCONNECT WIRE HARNESS AND CONNECTOR

a.
U152359

Tilt the transmission downward.

NOTICE:

Make sure the cooling fan does not contact the fan shroud.



b.

Disconnect the park/neutral position switch connector, 2 transmission wire connectors, 2 speed sensor connectors and 2 or 3 transfer control side connectors.

U164680

HINT:

Detach the claw, press down the lever, and then disconnect the transmission wire connector.



c.

Disconnect the 8 harness clamps.


d.

Remove the 2 bolts and disconnect the wire harness.


Hide 12140 26.REMOVE OIL PAN COVER

C172394

a.

Remove the 2 bolts and oil pan cover.


Hide 35119A 27.REMOVE TRANSMISSION HOUSING COVER

C175581

a.

Remove the 3 bolts and transmission housing cover.


Hide 35000 28.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

C175537

a.

Remove the 10 bolts and transmission.

NOTICE:

Do not use excess force to pry off the transmission assembly.



Hide 36179 29.REMOVE LOWER TRANSFER CASE PROTECTOR

a.
C344256

Detach the clamp and remove the 7 bolts and lower transfer case protector.


Hide 32000 31.REMOVE TORQUE CONVERTER ASSEMBLY

a.
C337054E01
0.769,0.216 0.955,0.404 0.186,0.188 10 *a 1.69,0.205 0.989,0.316 0.989,0.316 1.694,0.55 false

Put matchmarks on the automatic transmission assembly and the torque converter assembly.

Text in Illustration
*a Matchmark


b.

Remove the torque converter assembly from the automatic transmission assembly.