1.DISCHARGE FUEL SYSTEM PRESSURE
2. PRECAUTION
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
52119A
4.REMOVE FRONT BUMPER COVER
for Standard (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER(for Standard)>REMOVAL)
w/ Winch (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER(w/ Winch)>REMOVAL)
52521
5.REMOVE FRONT BUMPER UPPER CENTER RETAINER (w/ Air Cooled Transmission Oil Cooler)
for Standard (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER(for Standard)>REMOVAL)
w/ Winch (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER(w/ Winch)>REMOVAL)
32917
6.REMOVE TRANSMISSION OIL COOLER AIR DUCT (w/ Air Cooled Transmission Oil Cooler)
53293C
7.REMOVE RADIATOR SIDE DEFLECTOR RH (w/o Air Cooled Transmission Oil Cooler)
53294C
8.REMOVE RADIATOR SIDE DEFLECTOR LH
53301
9.REMOVE HOOD SUB-ASSEMBLY
Remove the 2 hood support bolts and disconnect the hood supports.
Remove the hood support assembly while supporting the hood by hand.
Remove the 4 bolts and hood.
55781E
10.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
53783
11.REMOVE FRONT FENDER APRON TRIM PACKING B
53785B
12.REMOVE FRONT FENDER APRON TRIM PACKING D
53782
13.REMOVE FRONT FENDER APRON TRIM PACKING A
53784
14.REMOVE FRONT FENDER APRON TRIM PACKING C
51405A
15.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
Remove the 10 bolts and No. 1 engine under cover sub-assembly.
51442
16.REMOVE NO. 2 ENGINE UNDER COVER
Remove the 2 bolts and No. 2 engine under cover.
51440
17.REMOVE OIL PAN PROTECTOR ASSEMBLY
Remove the 4 bolts and oil pan protector assembly.
11209
18.REMOVE V-BANK COVER SUB-ASSEMBLY
19.DRAIN ENGINE OIL
20.DRAIN ENGINE COOLANT
21.DRAIN AUTOMATIC TRANSMISSION FLUID
28800
22.REMOVE BATTERY
Remove the bolt and loosen the nut.
Detach the hook of the battery clamp from the battery bracket, and then remove the battery clamp.
Remove the battery.
17705
23.REMOVE AIR CLEANER AND HOSE
16571C
24.REMOVE NO. 1 RADIATOR HOSE
16711
25.REMOVE FAN SHROUD
16572D
26.REMOVE NO. 2 RADIATOR HOSE
16400
27.REMOVE RADIATOR ASSEMBLY
17343
28.DISCONNECT NO. 3 AIR INJECTION SYSTEM HOSE (w/ Secondary Air Injection System)
Disconnect the No. 3 air injection system hose from the air tube sub-assembly.
16289
29.REMOVE NO. 5 WATER BY-PASS PIPE
25625C
30.REMOVE EGR VALVE BRACKET
12261
31.REMOVE PCV HOSE ASSEMBLY
17361
32.REMOVE AIR TUBE SUB-ASSEMBLY (w/ Secondary Air Injection System)
17111
33.REMOVE INTAKE MANIFOLD
11452
34.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
44348A
35.DISCONNECT SUCTION HOSE
44410
36.DISCONNECT PRESSURE FEED TUBE
44310
37.REMOVE VANE PUMP ASSEMBLY
27020
38.REMOVE GENERATOR ASSEMBLY
for 130A, 150A Type:
(See page Power Source / Network>1UR-FE (BATTERY / CHARGING)>GENERATOR (for 130 A, 150 A Type)>REMOVAL)
for 180A Type:
(See page Power Source / Network>1UR-FE (BATTERY / CHARGING)>GENERATOR (for 180 A Type)>REMOVAL)
88320
39.DISCONNECT COOLER COMPRESSOR ASSEMBLY
37117
40.REMOVE PROPELLER SHAFT HEAT INSULATOR
89465
41.DISCONNECT HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)
89465
42.DISCONNECT HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)
17430
43.REMOVE TAILPIPE ASSEMBLY
17420
44.REMOVE CENTER EXHAUST PIPE ASSEMBLY
17450B
45.REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY
17410
46.REMOVE FRONT EXHAUST PIPE ASSEMBLY
17119
47.REMOVE NO. 2 MANIFOLD STAY
17118
48.REMOVE MANIFOLD STAY
17168
49.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
17150
50.REMOVE EXHAUST MANIFOLD ASSEMBLY LH
17167
51.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
17140
52.REMOVE EXHAUST MANIFOLD ASSEMBLY RH
28192
53.REMOVE STARTER COVER
28100
54.REMOVE STARTER ASSEMBLY
23271F
55.DISCONNECT FUEL HOSE AND FUEL TUBE SUB-ASSEMBLY
Remove the fuel pipe clamp from the fuel tube connector.
Disconnect the fuel hose and fuel tube sub-assembly (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).
82121
56.DISCONNECT ENGINE WIRE
Disconnect the clamp and ECM connector.
Refer to the following procedures to disconnect the ECM connector (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>ECM>REMOVAL).
Disconnect the 4 connectors and 2 clamps from the connector holder block.
Remove the bolt and disconnect the ground wire.
Remove the nut and disconnect the wire and 2 clips from the engine room junction block.
Disconnect the 2 connectors and 2 clips from the engine room junction block.
w/ Secondary Air Injection System:
Disconnect the 2 air injection control driver connectors.
Remove the bolt, disconnect the clamp and ground wire.
Remove the nut and disconnect the wire from the positive (+) battery cable.
Disconnect the 2 connectors and 2 clips from the engine room junction block.
w/ Secondary Air Injection System:
Disconnect the connector and clamp.
w/ Winch:
Detach the wire harness clamp, remove the nut and disconnect the ground wire from the wire harness clamp bracket.
32943B
57.DISCONNECT TRANSMISSION OIL COOLER HOSE
32907A
58.REMOVE OIL COOLER TUBE
59.REMOVE FRONT PROPELLER SHAFT ASSEMBLY
60.REMOVE PROPELLER SHAFT ASSEMBLY
32101A
61.REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT
35000
62.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY
16268
63.REMOVE NO. 1 WATER BY-PASS PIPE (w/ ATF Warmer)
w/ Rear Heater:
Disconnect the 6 water hoses.
Remove the 2 bolts and No. 1 water by-pass pipe.
w/o Rear Heater:
Disconnect the 4 water hoses.
Remove the 2 bolts and No. 1 water by-pass pipe.
87207A
64.REMOVE NO. 1 WATER BY-PASS PIPE (w/o ATF Warmer)
Disconnect the hose.
Remove the 2 bolts and No. 1 water by-pass pipe.
12371
65.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR
32101
66.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY
Using SST, hold the crankshaft.
Remove the 10 bolts, the rear drive plate spacer, the drive plate and ring gear, and the crankshaft angle sensor rotor.
12281A
67.INSTALL ENGINE HANGER
Install 2 engine hangers with 2 bolts as shown in the illustration.
| Engine Hanger | 12281-38150 |
| Bolt | 90119-14120 |
68.REMOVE ENGINE ASSEMBLY
Attach an engine sling device and hang the engine with a chain block.
| *1 | Engine Hanger |
| *2 | Engine |
| *a | 50° or less |
When hanging the engine, make sure to hang the engine with the angle of the sling device at 50° or less. Otherwise, the engine or engine hangers may be damaged.
Remove the 2 nuts and 4 bolts from the front engine mounting insulator LH and RH.
| *A | for LH Side |
| *B | for RH Side |
Lift the engine out of the vehicle carefully.
Make sure the engine is clear of all wiring, hoses and cables.
With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.
Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.
Remove the front engine mounting insulator LH and RH.
Place the engine onto a workbench.
69.INSTALL ENGINE STAND
Install the engine to an engine stand with bolts.
Remove the 2 bolts and 2 engine hangers.
12362A
70.REMOVE FRONT ENGINE MOUNTING INSULATOR LH
Remove the nut and mounting insulator.
12361
71.REMOVE FRONT ENGINE MOUNTING INSULATOR RH
Remove the nut and mounting insulator.
12316A
72.REMOVE NO. 2 FRONT ENGINE MOUNTING BRACKET LH
Remove the bolt and No. 2 front engine mounting bracket LH.