Home › Engine / Hybrid System › 1GR-FE (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2015.08–2017.08
RM2660E _51 Engine / Hybrid System _052778 1GR-FE ENGINE MECHANICAL _0255060 ENGINE ASSEMBLY A

1GR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 53301 5.REMOVE HOOD SUB-ASSEMBLY

a.
A174152

Remove the 2 hood support bolts and disconnect the hood supports.


b.

Remove the 4 bolts and hood.


Hide 55781E 6.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53806 7.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Hide 53805 8.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Hide 51405A 9.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 51442 10.REMOVE NO. 2 ENGINE UNDER COVER

a.

Remove the 2 bolts and No. 2 engine under cover.


Hide 32917 16.REMOVE TRANSMISSION OIL COOLER AIR DUCT (w/ Air Cooled Transmission Oil Cooler)

Hide 53293C 17.REMOVE RADIATOR SIDE DEFLECTOR RH (w/o Air Cooled Transmission Oil Cooler)

Hide 53294C 18.REMOVE RADIATOR SIDE DEFLECTOR LH

Hide 16571C 19.REMOVE NO. 1 RADIATOR HOSE

Hide 16572D 20.REMOVE NO. 2 RADIATOR HOSE

Hide 32907A 21.DISCONNECT OIL COOLER TUBE (w/ Air Cooled Transmission Oil Cooler)

Hide 32921D 23.DISCONNECT INLET OIL COOLER HOSE (for Automatic Transmission)

Hide 32922A 24.DISCONNECT OUTLET OIL COOLER HOSE (for Automatic Transmission)

Hide 27.REMOVE AIR CLEANER CAP AND HOSE

a.
A267624

Remove the air cleaner cap and hose.

i.

Disconnect the mass air flow meter connector, vacuum hose and ventilation hose and detach the clamp.


ii.

Loosen the clamp.


iii.

Unfasten the 4 hook clamps, and then remove the bolt and the air cleaner cap and hose.



Hide 28.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

a.

Remove the air cleaner filter element.


b.
A270980

Remove the 3 bolts and air cleaner case.


Hide 29.REMOVE AIR TUBE ASSEMBLY (w/ Secondary Air Injection System)

Hide 82121 31.DISCONNECT ENGINE WIRE

a.

Remove the junction block cover.


b.
A370846

Disconnect the ECM connector (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>ECM>REMOVAL).


c.

Detach the wire harness clamp.


d.

Disconnect the 4 connectors from the junction block.


e.

Remove the engine room relay block cover.


f.
A370847

Remove the bolt and disconnect the ground wire from the bracket.


g.

w/ Secondary Air Injection System:

Disconnect the 2 air injection control driver connectors and detach the clamp.


h.

Disconnect the 2 connectors and 2 clips from the engine room junction block.


i.

Remove the nut and disconnect the wire and 2 clips from the engine room junction block.


j.

Remove the nut and disconnect the wire from the positive (+) battery cable.


k.

Disconnect the cable from the positive (+) battery terminal.


l.

Remove the bolt and detach the wire harness clamp, and then disconnect the ground wire from the body.


m.
A267745

Disconnect the connector and detach the 2 clamps.


n.
A368699

w/ Winch:

Remove the 2 bolts and winch ground wire.


o.
A263401

Disconnect the power steering switch connector and detach the clamp.


p.
A263400

w/ Secondary Air Injection System:

Disconnect the air pump connector and detach the clamp.


Hide 89465 32.REMOVE HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)

Hide 17420 34.REMOVE CENTER EXHAUST PIPE ASSEMBLY

Hide 17450B 35.REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY

Hide 89465 36.REMOVE HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)

Hide 17410 37.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 53782 38.REMOVE FRONT FENDER APRON TRIM PACKING A

Hide 53783 39.REMOVE FRONT FENDER APRON TRIM PACKING B

Hide 53784 40.REMOVE FRONT FENDER APRON TRIM PACKING C

Hide 53785B 41.REMOVE FRONT FENDER APRON TRIM PACKING D

Hide 17361 43.REMOVE AIR TUBE (w/ Secondary Air Injection System)

Hide 45203A 44.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT

Hide 17167 45.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17104 46.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH

Hide 17362 48.REMOVE NO. 2 AIR TUBE (w/ Secondary Air Injection System)

Hide 17168 49.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17105 50.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH

Hide 87209 51.DISCONNECT WATER HOSE SUB-ASSEMBLY

a.
A263403E02
0.021,2.365 0.438,2.656 0.417,0.292 10 true *B 0.021,0.01 0.396,0.354 0.375,0.344 10 true *A

Disconnect the water hoses.

Text in Illustration
*A w/o Rear Heater
*B w/ Rear Heater


Hide 44320 52.DISCONNECT VANE PUMP ASSEMBLY

Hide 88711 54.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

Hide 23801P 57.DISCONNECT NO. 1 AND NO. 2 FUEL PIPES

a.
A174380

Disconnect the No. 1 and No. 2 fuel pipes (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 33030 58.REMOVE MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)

Hide 35000 59.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)

Hide 12371 60.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

HINT:

Only perform this procedure when replacement of the engine mounting insulator is necessary.


a.
C171491

Remove the 4 bolts and rear engine mounting insulator from the transmission.


Hide 32907C 61.DISCONNECT NO. 1 OIL COOLER HOSE TUBE SUB-ASSEMBLY (for Automatic Transmission)

a.
A177664

Remove the 2 bolts and cooler hose tube.


Hide 31210 62.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 31250 63.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)

Hide 13405 64.REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

a.
A224775E05
1.427,0.354 1.635,0.135 1.635,0.135 2.74,0.135 false 2,0.448 2.313,0.135 false 2.771,0.052 3.135,0.323 0.365,0.271 10 true SST

Using SST, hold the crankshaft.

SST
09213-54015  (91651-60855)
09330-00021  


b.
A224776

Remove the 8 bolts and flywheel.

NOTICE:

Do not reuse the bolts.



Hide 32101 65.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)

a.
A224775E05
1.427,0.354 1.635,0.135 1.635,0.135 2.74,0.135 false 2,0.448 2.313,0.135 false 2.771,0.052 3.135,0.323 0.365,0.271 10 true SST

Using SST, hold the crankshaft.

SST
09213-54015  (91651-60855)
09330-00021  


b.
A224777

Remove the 8 bolts, rear spacer, drive plate and front spacer.

NOTICE:

Do not reuse the bolts.



Hide 66.INSTALL ENGINE HANGER

a.
U147659E04
3,0.417 2.917,0.417 2.917,0.417 2.76,0.635 false 0.302,0.635 0.563,0.635 0.563,0.635 0.792,0.844 true 0.115,0.552 0.313,0.771 0.198,0.219 10 false *1 3.021,0.323 3.208,0.5 0.188,0.177 10 false *2 3.115,1.74 3.219,1.906 0.104,0.167 10 false 1 2.406,1.927 2.51,2.094 0.104,0.167 10 false 2 1.198,1.802 1.302,1.969 0.104,0.167 10 false 1 0.458,1.708 0.563,1.875 0.104,0.167 10 false 2

Install 2 engine hangers with 4 bolts as shown in the illustration.

Torque:
33 N*m (337 kgf*cm, 24 ft.*lbf)

Text in Illustration
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger

HINT:
No. 1 Engine Hanger 12281-31110
No. 2 Engine Hanger 12282-31140
Bolt 91671-C0830



Hide 67.REMOVE ENGINE ASSEMBLY

a.

Attach an engine sling device and hang the engine with a chain block.


b.
A263404

Remove the 2 nuts and 4 bolts from the front engine mounting insulator LH and RH.


c.

Lift the engine out of the vehicle carefully.

NOTICE:
·

Make sure the engine is clear of all wiring and hoses.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.

·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.




d.

Remove the front engine mounting insulator LH and RH.


e.

Place the engine onto a work bench.


Hide 68.INSTALL ENGINE STAND

a.

Install the engine onto an engine stand with bolts.


b.

Remove the 4 bolts and 2 engine hangers.


Hide 12316A 69.REMOVE FRONT NO. 2 ENGINE MOUNTING BRACKET LH

a.

Remove the bolt and front No. 2 engine mounting bracket LH.