Home › Drivetrain › JF2A (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM › from 2015.08
RM2660E _52 Drivetrain _052810 JF2A TRANSFER / 4WD / AWD _0255329 TRANSFER SYSTEM C

JF2A TRANSFER / 4WD / AWD  TRANSFER SYSTEM  P17AA  Transfer Shift Motor Control Circuit High  


DESCRIPTION

This DTC is output when a short to B+ in the high-low transfer shift motor, center differential lock shift motor and differential lock shift motor* drive circuit is detected.

*: w/ Rear Differential Lock


DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P17AA
1.

While the ignition switch is turned to ON or directly after the ignition switch is turned to ON (high-low transfer shift motor, center differential lock shift motor and differential lock shift motor* not operating)

2.

Short to B+ in the high-low transfer shift motor, center differential lock shift motor and differential lock shift motor* drive circuits

3.

0.5 seconds or more (if directly after ignition switch is turned ON, 0.05 seconds)

4.

1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

Transfer shift actuator assembly

·

Differential lock shift actuator*



*: w/ Rear Differential Lock


WIRING DIAGRAM

PROCEDURE

1.CHECK ACTUATOR ASSEMBLY (TRANSFER SHIFT MOTOR OR LOCK SHIFT MOTOR)
a.

Disconnect the A28 4 wheel drive control ECU connector.


b.
U164489E01
1.905,2.723 2.290,2.895 0.385,0.172 10 TM1 1.931,2.225 2.041,2.723 false 1.658,0.895 1.930,1.077 0.272,0.181 10 A28 0.185,0.134 0.570,0.305 0.385,0.172 10 *a 1.399,2.721 1.784,2.893 0.385,0.172 10 TM2 1.592,2.706 1.655,2.239 false 0.793,1.184 1.178,1.356 0.385,0.172 10 HM1 1.425,1.734 1.162,1.329 false 0.885,2.697 1.270,2.869 0.385,0.172 10 HM2 1.163,2.647 1.414,2.229 false 2.18,1.765 2.47,1.365 false 2.498,1.259 2.883,1.431 0.385,0.172 10 M1*A 2.559,2.745 2.944,2.917 0.385,0.172 10 M2*A 2.232,2.219 2.669,2.684 false

Measure the voltage according to the value(s) in the table below

Standard Voltage:
Transfer Shift Actuator Assembly (High-low Transfer Shift Motor) Side
Tester Connection Condition Specified Condition
A28-2 (HM1) or A28-6 (HM2) - Body ground Ignition switch ON Below 1 V

Transfer Shift Actuator Assembly (Center Differential Lock Shift Motor) Side
Tester Connection Condition Specified Condition
A28-8 (TM1) or A28-7 (TM2) - Body ground Ignition switch ON Below 1 V

Differential Lock Shift Actuator (Differential Lock Shift Motor) Side (w/ Rear Differential Lock)
Tester Connection Condition Specified Condition
A28-3 (M1) or A28-9 (M2) - Body ground Ignition switch ON Below 1 V


Text in Illustration
*A w/ Rear Differential Lock
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)

Result:
Result Proceed to
OK for LHD A
for RHD B
NG (transfer shift actuator assembly (high-low transfer shift motor) side) C
NG (transfer shift actuator assembly (center differential lock shift motor) side) D
NG (differential lock shift actuator (differential lock shift motor) side (w/ Rear Differential Lock)) E




A

B

C

2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND TRANSFER SHIFT ACTUATOR ASSEMBLY - BODY GROUND)

D

3.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND TRANSFER SHIFT ACTUATOR ASSEMBLY - BODY GROUND)

E

4.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND DIFFERENTIAL LOCK SHIFT ACTUATOR - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND TRANSFER SHIFT ACTUATOR ASSEMBLY - BODY GROUND)
a.

Disconnect the A28 4 wheel drive control ECU connector.


b.

Disconnect the C38 transfer shift actuator assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A28-2 (HM1) or C38-1 (HM1) - Body ground Ignition switch ON Below 1 V
A28-6 (HM2) or C38-2 (HM2) - Body ground Ignition switch ON Below 1 V




OK

REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND TRANSFER SHIFT ACTUATOR ASSEMBLY - BODY GROUND)
a.

Disconnect the A28 4 wheel drive control ECU connector.


b.

Disconnect the C37 transfer shift actuator assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A28-8 (TM1) or C37-1 (TM1) - Body ground Ignition switch ON Below 1 V
A28-7 (TM2) or C37-2 (TM1) - Body ground Ignition switch ON Below 1 V




OK

REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND DIFFERENTIAL LOCK SHIFT ACTUATOR - BODY GROUND)
a.

Disconnect the A28 4 wheel drive control ECU connector.


b.

Disconnect the f1 differential lock shift actuator connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A28-3 (M1) or f1-3 - Body ground Ignition switch ON Below 1 V
A28-9 (M2) or f1-2 - Body ground Ignition switch ON Below 1 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR