Home › Drivetrain › JF2A (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM › 2015.08–2017.08
RM2660E _52 Drivetrain _052810 JF2A TRANSFER / 4WD / AWD _0255329 TRANSFER SYSTEM J

JF2A TRANSFER / 4WD / AWD  TRANSFER SYSTEM  Center Differential Lock Switch Circuit  


WIRING DIAGRAM

C346661E03
0.427,1.198 3.115,1.667 2.688,0.469 10 false Center Differential Lock Switch (Integration Control and Panel Assembly)*1 0.865,2.99 3.229,3.26 2.365,0.271 10 false Center Differential Lock Switch 0.594,1 0.865,1.188 0.271,0.188 10 false V9 2.469,0.563 2.865,0.813 0.396,0.25 10 false 9 0.729,0.552 0.969,0.74 0.24,0.188 10 false 5 2.083,0.573 2.479,0.75 0.396,0.177 10 false CPU 0.865,2.771 2.167,2.979 1.302,0.208 10 false E178*2, G24*3 3.323,2.958 3.615,3.146 0.292,0.188 10 false A27 3.302,3.135 5.125,3.354 1.823,0.219 10 false 4 Wheel Drive Control ECU 3.354,2.177 3.646,2.323 0.292,0.146 10 false 14 3.729,2.156 4.031,2.365 0.302,0.208 10 false DL 4.417,1.271 4.677,1.469 0.26,0.198 10 false IG 3.01,3.573 6.802,3.885 3.792,0.313 10 false *1: for Automatic Transmission w/ Entry and Start System 3.01,3.969 6.927,4.26 3.917,0.292 10 false *2: for Manual Transmission w/ Entry and Start System 3.021,4.375 5.229,4.625 2.208,0.25 10 false *3: w/o Entry and Start System 0.719,2.188 0.885,2.406 0.167,0.219 10 false 6 2.458,2.219 2.854,2.469 0.396,0.25 10 false 9 2.083,2.208 2.479,2.385 0.396,0.177 10 false CPU 0.958,0.552 1.26,0.76 0.302,0.208 10 false E 0.917,2.198 1.219,2.406 0.302,0.208 10 false E 0.865,4.198 2.792,4.438 1.927,0.24 10 false : CAN Communication Line 5.135,3.073 7.146,3.385 2.01,0.313 10 false Combination Meter Assembly

PROCEDURE

1.CHECK CENTER DIFFERENTIAL LOCK INDICATOR LIGHT
a.

Turn the ignition switch to ON.


b.

Check the center differential lock indicator light.


c.

for Automatic Transmission w/ Entry and Start System:

Press the center differential lock switch (integration control and panel assembly) .

for Manual Transmission w/ Entry and Start System:

Press the center differential lock switch.

w/o Entry and Start System:

Press the center differential lock switch.


d.

After 60 seconds, check the center differential lock indicator light.

Result
Result Proceed to
The center differential lock indicator light blinks, turns off or illuminates A
Center differential lock indicator light remains off regardless of switch operation B
Center differential lock indicator remains illuminated regardless of switch operation C
Center differential lock indicator light rapidly blinks D

Blinking: Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)

Rapidly blinking: Blinks at 0.25 second intervals (0.25 seconds on and 0.25 seconds off)




A

END

B

2.CHECK CAN COMMUNICATION LINE

C

7.CHECK CAN COMMUNICATION LINE

D

2.CHECK CAN COMMUNICATION LINE
a.

Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN bus (for LHD with Central Gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM, for LHD without Central Gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD without Central Gateway ECU)>DIAGNOSIS SYSTEM, for RHD with Central Gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM, for RHD without Central Gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD without Central Gateway ECU)>DIAGNOSIS SYSTEM).

OK:

"Bus Check" indicates no malfunctions in CAN communication.


Result
Result Proceed to
DTC is not output A
DTC is output for LHD with Central Gateway ECU B
for LHD without Central Gateway ECU C
for RHD with Central Gateway ECU D
for RHD without Central Gateway ECU E



A

3.READ VALUE USING GTS

B

C

D

E

3.READ VALUE USING GTS
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Turn the ignition switch to ON.


e.

Enter the following menus: Powertrain / Four Wheel Drive / Data List.


f.

According to the display on the GTS, read the Data List.

Four Wheel Drive
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Center Differential Lock Control SW Center differential lock switch status/
ON or OFF
ON: Switch pressed and held
OFF: Switch not pressed
-

OK:

for Automatic Transmission w/ Entry and Start System:

Display changes according to center differential lock switch (integration control and panel assembly) operation.

for Manual Transmission w/ Entry and Start System:

Display changes according to center differential lock switch operation.

w/o Entry and Start System:

Display changes according to center differential lock switch operation.




OK

4.INSPECT COMBINATION METER ASSEMBLY

NG

5.INSPECT INTEGRATION CONTROL AND PANEL ASSEMBLY OR CENTER DIFFERENTIAL LOCK SWITCH
4.INSPECT COMBINATION METER ASSEMBLY
a.

Turn the ignition switch off.


b.

Perform an Active Test of the combination meter assembly using the GTS (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).


c.

Check the combination meter assembly.

OK:

The center differential lock indicator light turns on or off in accordance with the GTS.


Result:
Result Proceed to
OK for LHD A
for RHD B
NG C




A

B

C

5.INSPECT INTEGRATION CONTROL AND PANEL ASSEMBLY OR CENTER DIFFERENTIAL LOCK SWITCH
a.

for Automatic Transmission w/ Entry and Start System:

i.

Remove the center differential lock switch (integration control and panel assembly) (See page Drivetrain>JF2A (TRANSFER / 4WD / AWD)>CENTER DIFFERENTIAL LOCK SWITCH(w/ Entry and Start System)>REMOVAL).


ii.

Inspect the center differential lock switch (integration control and panel assembly) (See page Drivetrain>JF2A (TRANSFER / 4WD / AWD)>CENTER DIFFERENTIAL LOCK SWITCH(w/ Entry and Start System)>INSPECTION).

OK:

The center differential lock switch (integration control and panel assembly) operates normally.




b.

for Manual Transmission w/ Entry and Start System:


ii.

Inspect the center differential lock switch (See page Drivetrain>JF2A (TRANSFER / 4WD / AWD)>CENTER DIFFERENTIAL LOCK SWITCH(w/ Entry and Start System)>INSPECTION).

OK:

The center differential lock switch operates normally.




c.

w/o Entry and Start System:


ii.

Inspect the center differential lock switch (See page Drivetrain>JF2A (TRANSFER / 4WD / AWD)>CENTER DIFFERENTIAL LOCK SWITCH(w/o Entry and Start System)>INSPECTION).

OK:

The center differential lock switch operates normally.




Result:
Result Proceed to
OK A
NG for Automatic Transmission w/ Entry and Start System B
for Manual Transmission w/ Entry and Start System C
w/o Entry and Start System D



A

6.CHECK HARNESS AND CONNECTOR ((4 WHEEL DRIVE CONTROL ECU - CENTER DIFFERENTIAL LOCK SWITCH)

B

C

D

6.CHECK HARNESS AND CONNECTOR ((4 WHEEL DRIVE CONTROL ECU - CENTER DIFFERENTIAL LOCK SWITCH)
a.

Disconnect the A27 4 wheel drive control ECU connector.


b.

for Automatic Transmission w/ Entry and Start System:

Disconnect the V9 center differential lock switch (integration control and panel assembly) connector.


c.

for Manual Transmission w/ Entry and Start System:

Disconnect the E178 center differential lock switch connector.


d.

w/o Entry and Start System:

Disconnect the G24 center differential lock switch connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Automatic Transmission w/ Entry and Start System:
Tester Connection Condition Specified Condition
A27-14 (DL) - V9-9 (CPU) Always Below 1 Ω
V9-5 (E) - Body ground Always Below 1 Ω

for Manual Transmission w/ Entry and Start System:
Tester Connection Condition Specified Condition
A27-14 (DL) - E178-9 (CPU) Always Below 1 Ω
E178-6 (E) - Body ground Always Below 1 Ω

w/o Entry and Start System:
Tester Connection Condition Specified Condition
A27-14 (DL) - G24-9 (CPU) Always Below 1 Ω
G24-6 (E) - Body ground Always Below 1 Ω




A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK CAN COMMUNICATION LINE
a.

Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN bus (for LHD with Central Gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM, for LHD without Central Gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD without Central Gateway ECU)>DIAGNOSIS SYSTEM, for RHD with Central Gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM, for RHD without Central Gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD without Central Gateway ECU)>DIAGNOSIS SYSTEM).

OK:

"Bus Check" indicates no malfunctions in CAN communication.


Result
Result Proceed to
DTC is not output A
DTC is output for LHD with Central Gateway ECU B
for LHD without Central Gateway ECU C
for RHD with Central Gateway ECU D
for RHD without Central Gateway ECU E



A

8.READ VALUE USING GTS (CENTER DIFFERENTIAL LOCK INDICATOR LIGHT)

B

C

D

E

8.READ VALUE USING GTS (CENTER DIFFERENTIAL LOCK INDICATOR LIGHT)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Turn the ignition switch to ON.


e.

Enter the following menus: Powertrain / Four Wheel Drive / Data List.


f.

According to the display on the GTS, read the Data List.

Four Wheel Drive
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Center Differential Lock Indicator Request Center differential lock indicator light request/
Blink3, Blink2, Blink1, ON or OFF
·

Blink3: Indicator light rapidly blinks

·

Blink2: Indicator light blinks 3 times

·

Blink1: Indicator light blinks

·

ON: Indicator light illuminates

·

OFF: Indicator light turns off


·

Blinking: 0.5 second intervals (0.5 seconds on and 0.5 seconds off)

·

Rapidly blinking: 0.25 second intervals (0.25 seconds on and 0.25 seconds off)



i.

for Automatic Transmission w/ Entry and Start System:

Turn the differential lock switch (integration control and panel assembly) on and off several times and check the GTS display condition of the center differential lock indicator light.

for Manual Transmission w/ Entry and Start System:

Turn the differential lock switch on and off several times and check the GTS display condition of the center differential lock indicator light.

w/o Entry and Start System:

Turn the differential lock switch on and off several times and check the GTS display condition of the center differential lock indicator light.

Result:
Result Proceed to
Data List continues to display ON even when center differential lock switch (integration control and panel assembly) is operated*1
Data List continues to display ON even when center differential lock switch is operated*2. *3
for LHD A
for RHD B
Data List display changes according to center differential lock switch (integration control and panel assembly) operation*1
Data List display changes according to center differential lock switch operation*2, *3
C


*1: for Automatic Transmission w/ Entry and Start System

*2: for Manual Transmission w/ Entry and Start System

*3: w/o Entry and Start System





A

B

C