Home › Suspension › SUSPENSION CONTROL › ACTIVE HEIGHT CONTROL SUSPENSION › from 2015.08
RM2660E _53 Suspension _052813 SUSPENSION CONTROL _0255367 ACTIVE HEIGHT CONTROL SUSPENSION C

SUSPENSION CONTROL  ACTIVE HEIGHT CONTROL SUSPENSION  C1736  Front Suspension Control Valve RH Malfunction  C1737  Front Suspension Control Valve LH Malfunction  


DESCRIPTION

In order to decrease roll angle/pitch angle, the suspension control ECU turns the spring rate switching valve in the front suspension control valve off/on to change the fluid lines when the acceleration sensor (airbag sensor assembly) or yaw rate sensor (airbag sensor assembly) signal is input into the suspension control ECU. Normally, the spring rate switching valve is open.

DTC Code Detection Condition Trouble area
C1736 When either of the following is detected:
·

With the spring rate switch valve RH not activated, an open signal of the spring rate switch valve RH is detected for 1 second or more.

·

With the spring rate switch valve RH activated, a short signal of the spring rate switch valve RH is detected 8 times successively.


·

Harness or connector

·

Front suspension control valve RH (Front spring rate switching valve RH)

·

Suspension control ECU

·

No. 1 height control valve


C1737 When either of the following is detected:
·

With the spring rate switch valve LH not activated, an open signal of the spring rate switch valve LH is detected for 1 second or more.

·

With the spring rate switch valve LH activated, a short signal of the spring rate switch valve LH is detected 8 times successively.


·

Harness or connector

·

Front suspension control valve LH (Front spring rate switching valve LH)

·

Suspension control ECU

·

No. 1 height control valve



WIRING DIAGRAM

C176953E01
1.662,1.261 4.202,1.676 2.540,0.414 10 Front Spring Rate Switching Valve RH 5.576,0.785 6.166,0.986 0.590,0.201 10 CRFR 5.146,0.662 5.413,0.949 0.267,0.287 10 11 1.662,2.896 4.202,3.310 2.540,0.414 10 Front Spring Rate Switching Valve LH 5.506,2.427 6.096,2.629 0.590,0.201 10 CRFL 5.128,2.304 5.395,2.591 0.267,0.287 10 23 4.913,4.551 6.559,4.809 1.647,0.258 10 Suspension Control ECU 5.136,3.837 5.403,3.989 0.267,0.152 10 1 4.913,4.355 5.300,4.520 0.387,0.165 10 K36 5.547,3.977 5.916,4.172 0.369,0.195 10 SLB 5.51,5.497 5.878,5.692 0.369,0.195 10 SLB 2.348,2.446 2.716,2.641 0.369,0.195 10 SLB 2.353,0.797 2.722,0.992 0.369,0.195 10 SLB 3.1,0.785 3.580,0.969 0.480,0.184 10 CRFR 3.137,2.45 3.562,2.671 0.424,0.221 10 CRFL 1.998,0.625 2.172,0.809 0.174,0.184 10 2 3.787,0.625 3.986,0.870 0.198,0.245 10 1 1.988,2.257 2.162,2.441 0.174,0.184 10 2 3.778,2.257 3.976,2.502 0.198,0.245 10 1 5.157,5.332 5.358,5.484 0.201,0.152 10 6 4.864,5.949 6.603,6.147 1.739,0.198 10 No. 1 Height Control Valve 4.864,5.824 5.177,6.050 0.313,0.226 10 N4 1.662,1.024 2.095,1.211 0.434,0.187 10 N10 1.662,2.682 2.039,2.878 0.377,0.196 10 N12

CAUTION / NOTICE / HINT

NOTICE:
·

Before performing troubleshooting, inspect the connectors of related circuits.

·

If the suspension control ECU or height control sensor is replaced, the vehicle height offset calibration must be performed (See page Suspension>SUSPENSION CONTROL>ACTIVE HEIGHT CONTROL SUSPENSION>INITIALIZATION).



HINT:

Power is supplied to the front suspension control valve and No. 1 height control valve from the suspension control ECU. If a short occurs in the power supply circuit in the No. 1 height control valve, DTC C1736 and/or C1737 will be stored. In this case, DTC C1741, C1742, C1743, C1744, C1753, C1754 and/or C1755 will also be stored.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (FRONT SPRING RATE SWITCHING VALVE)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Select the Active Test mode on the GTS.


d.

Check the operation of the front spring rate switching valve solenoid when operating the solenoid with the intelligent tester.

AHC
Tester Display Test Part Control Range Diagnostic Note
FR Gas Spring Switch Valve Front spring rate switching valve RH ON or OFF When the FR Gas Spring Switch Valve item of the Active Test is operated, the FR Gas Spring Switch Valve item of the Data List changes to ON/OFF.
FL Gas Spring Switch Valve Front spring rate switching valve LH ON or OFF When the FL Gas Spring Switch Valve item of the Active Test is operated, the FL Gas Spring Switch Valve item of the Data List changes to ON/OFF.

OK:

The front spring rate switching valve operates.




OK

2.RECONFIRM DTC OUTPUT

NG

3.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - FRONT SUSPENSION CONTROL VALVE)
2.RECONFIRM DTC OUTPUT

b.

Perform a road test.


c.

Check for DTCs.

Result
Result Proceed to
DTC is output A
DTC is not output B



A

REPLACE SUSPENSION CONTROL ECU

B

3.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - FRONT SUSPENSION CONTROL VALVE)
a.

Disconnect the N10*1 and/or N12*2 front suspension control valve connector.

HINT:

*1: for RH

*2: for LH



b.

Disconnect the K36 ECU connector.

U164799E02
5.24,1.771 4.854,2.188 4.854,2.188 4.854,2.292 false 5.573,1.802 6.292,2.198 6.292,2.198 6.292,2.302 false 1.615,2.083 2.073,2.427 2.073,2.427 2.146,2.427 false 1.615,2.031 2.073,2.083 2.073,2.083 2.167,2.083 false 1.594,1.958 2.104,1.75 2.104,1.75 2.167,1.75 false 0.771,0.094 3.135,0.448 2.365,0.354 10 false Rear view of wire harness connector: (to Suspension Control ECU) 4.302,0.104 6.667,0.458 2.365,0.354 10 false Front view of wire harness connector: (to Front Suspension Control Valve) 4.292,2.323 5.417,2.51 1.125,0.188 10 false CRFR*1, CRFL*2 6.188,2.333 6.5,2.5 0.313,0.167 10 false SLB 2.198,1.99 3.125,2.156 0.927,0.167 10 false 11 (CRFR)*1 2.198,2.344 3.135,2.542 0.938,0.198 10 false 23 (CRFL)*2 0.125,2.115 0.844,2.313 0.719,0.198 10 false *1: for RH 0.135,2.375 0.823,2.573 0.688,0.198 10 false *2: for LH 0.76,1.573 1.031,1.719 0.271,0.146 10 false K36 2.188,1.677 2.708,1.854 0.521,0.177 10 false 1 (SLB) 4.656,1.135 4.854,1.344 0.198,0.208 10 false *1 4.354,1.25 4.625,1.406 0.271,0.156 10 false N10 4.656,1.583 4.854,1.792 0.198,0.208 10 false *2 4.354,1.708 4.646,1.854 0.292,0.146 10 false N12


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K36-11 (CRFR) - N10-1 (CRFR) Always Below 1 Ω
K36-11 (CRFR) - Body ground Always 10 kΩ or higher
K36-23 (CRFL) - N12-1 (CRFL) Always Below 1 Ω
K36-23 (CRFL) - Body ground Always 10 kΩ or higher
K36-1 (SLB) - N10-2 (SLB) Always Below 1 Ω
K36-1 (SLB) - N12-2 (SLB) Always Below 1 Ω




OK

4.CHECK HARNESS AND CONNECTOR (BODY GROUND BETWEEN ECU - FRONT SUSPENSION CONTROL VALVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BODY GROUND BETWEEN ECU - FRONT SUSPENSION CONTROL VALVE)
a.

Disconnect the K36 ECU connector.


b.

Disconnect the N10*1 and/or N12*2 front suspension control valve connector.

HINT:

*1: for RH

*2: for LH



c.
U164793E01
0.319,0.278 2.684,0.635 2.365,0.357 10 Rear view of wire harness connector: (to Suspension Control ECU) 2.192,3.321 2.735,3.526 0.543,0.206 10 1 (SLB) 1.238,2.69 1.512,2.853 0.274,0.163 10 K36 1.619,3.548 2.054,3.408 2.054,3.408 2.14,3.408 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K36-1 (SLB) - Body ground Always 10 kΩ or higher




OK

5.INSPECT FRONT SUSPENSION CONTROL VALVE

NG

6.CHECK HARNESS AND CONNECTOR (BODY GROUND BETWEEN ECU - NO. 1 HEIGHT CONTROL VALVE)
5.INSPECT FRONT SUSPENSION CONTROL VALVE
a.

Connect the N10 and/or N12 front suspension control valve connector.


b.
U164792E02
1.646,3.708 1.917,4.344 1.917,4.344 2.021,4.344 false 1.646,3.646 1.938,3.844 1.938,3.844 2.042,3.844 false 1.604,3.552 1.969,3.198 1.969,3.198 2.073,3.198 false 0.323,0.229 2.688,0.583 2.365,0.354 10 false Rear view of wire harness connector: (to Suspension Control ECU) 2.094,3.75 3.063,3.958 0.969,0.208 10 false 11 (CRFR)*1 2.094,4.26 3.167,4.438 1.073,0.177 10 false 23 (CRFL)*2 0.135,3.885 0.865,4.052 0.729,0.167 10 false *1: for RH 0.135,4.198 0.906,4.375 0.771,0.177 10 false *2: for LH 1.25,2.677 1.521,2.844 0.271,0.167 10 false K36 2.115,3.125 2.646,3.313 0.531,0.188 10 false 1 (SLB)

Disconnect the K36 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K36-11 (CRFR) - K36-1 (SLB) at 20°C (68°F) 4.58 to 5.02 Ω
K36-23 (CRFL) - K36-1 (SLB) at 20°C (68°F) 4.58 to 5.02 Ω




OK

REPLACE SUSPENSION CONTROL ECU

NG

6.CHECK HARNESS AND CONNECTOR (BODY GROUND BETWEEN ECU - NO. 1 HEIGHT CONTROL VALVE)
a.

Disconnect the N4 No. 1 height control valve connector.


b.

Disconnect the K36 ECU connector.


c.
U164793E01
0.319,0.278 2.684,0.635 2.365,0.357 10 Rear view of wire harness connector: (to Suspension Control ECU) 2.192,3.321 2.735,3.526 0.543,0.206 10 1 (SLB) 1.238,2.69 1.512,2.853 0.274,0.163 10 K36 1.619,3.548 2.054,3.408 2.054,3.408 2.14,3.408 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K36-1 (SLB) - Body ground Always 10 kΩ or higher




OK

7.CHECK HARNESS AND CONNECTOR (NO. 1 HEIGHT CONTROL VALVE - SUSPENSION CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (NO. 1 HEIGHT CONTROL VALVE - SUSPENSION CONTROL ECU)

OK

REPLACE NO. 1 HEIGHT CONTROL VALVE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR