Home › Suspension › SUSPENSION CONTROL › ACTIVE HEIGHT CONTROL SUSPENSION › 2014.08–2015.08
RM2660E _53 Suspension _052813 SUSPENSION CONTROL _0255367 ACTIVE HEIGHT CONTROL SUSPENSION C

SUSPENSION CONTROL  ACTIVE HEIGHT CONTROL SUSPENSION  C1766  Height Control Pump Motor Current  


DESCRIPTION

In case that the height control has not finished in spite of performing the raise control for a certain period of time, the ECU interrupts the height control.

DTC Code Detection Condition Trouble Area
C1766 When the height control pump and motor operates continuously for 135 seconds.
·

Fluid leakage

·

No. 1 height control valve

·

Suspension control relay

·

Height control pump and motor

·

Clog in the fluid line

·

Suspension control ECU



CAUTION / NOTICE / HINT

NOTICE:
·

If the suspension control ECU or height control sensor is replaced, the vehicle height offset calibration must be performed (See page Suspension>SUSPENSION CONTROL>ACTIVE HEIGHT CONTROL SUSPENSION>INITIALIZATION).

·

When the cargo weight is extremely heavy, this DTC may be stored.



PROCEDURE

1.INSPECT FOR FLUID LEAK

OK

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (LEVELING VALVE, ACCUMULATOR VALVE AND GATE VALVE)

NG

REPAIR FLUID LEAK OR REPLACE LEAKING PART(S)

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (LEVELING VALVE, ACCUMULATOR VALVE AND GATE VALVE)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Select the Active Test mode on the intelligent tester.


d.

Check the operation of the leveling valve solenoid, accumulator valve solenoid and gate valve solenoid when operating the solenoid with the intelligent tester.

AHC
Tester Display Test Part Control Range Diagnostic Note
Front Right Height Solenoid Front height control solenoid valve RH ON or OFF Operation of solenoid can be heard.
Front Left Height Solenoid Front height control solenoid valve LH ON or OFF Operation of solenoid can be heard.
Rear Right Height Solenoid Rear height control solenoid valve RH ON or OFF Operation of solenoid can be heard.
Rear Left Height Solenoid Rear height control solenoid valve LH ON or OFF Operation of solenoid can be heard.
Accumulator Valve Accumulator solenoid valve ON or OFF Operation of solenoid can be heard.
Front Gate Valve Front gate solenoid valve ON or OFF When the Front Gate Valve item of the Active Test is operated, the Front Gate Valve item of the Data List changes to ON/OFF.
Rear Gate Valve Rear gate solenoid valve ON or OFF When the Rear Gate Valve item of the Active Test is operated, the Rear Gate Valve item of the Data List changes to ON/OFF.

OK:

The leveling valve solenoid, accumulator valve solenoid and/or gate valve solenoid operates.




OK

3.INSPECT SUSPENSION CONTROL RELAY (AHC)

NG

REPLACE NO. 1 HEIGHT CONTROL VALVE

3.INSPECT SUSPENSION CONTROL RELAY (AHC)
a.
C149624E01
1.283,0.718 1.439,0.874 0.156,0.156 10 5 1.282,1.272 1.438,1.427 0.156,0.156 10 2 0.24,0.722 0.396,0.877 0.156,0.156 10 3 0.235,1.285 0.391,1.441 0.156,0.156 10 1 3.167,0.968 3.323,1.124 0.156,0.156 10 5 1.969,1.701 2.125,1.857 0.156,0.156 10 2 1.393,0.974 1.549,1.130 0.156,0.156 10 3 2.699,0.245 2.854,0.400 0.156,0.156 10 1

Remove the suspension control relay from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminal 1 and 2 10 kΩ or higher
Battery voltage is applied to terminal 1 and 2 Below 1 Ω




OK

4.CHECK HEIGHT CONTROL PUMP AND MOTOR

NG

REPLACE SUSPENSION CONTROL RELAY

4.CHECK HEIGHT CONTROL PUMP AND MOTOR
a.

Remove the height control pump and motor (See page Suspension>SUSPENSION CONTROL>ACTIVE HEIGHT CONTROL PUMP AND MOTOR>REMOVAL).


b.

Inspect if the compressor is stuck.

i.
C177053E01
0.201,0.116 2.736,0.702 2.534,0.586 10 Component without harness connected: (Height Control Pump and Motor) 2.792,2.595 2.883,2.797 0.091,0.202 10 - 0.465,2.618 0.584,2.866 0.119,0.248 10 + 1.396,2.114 0.525,2.469 0.525,2.469 0.525,2.549 false 2.061,2.103 2.828,2.457 2.828,2.457 2.828,2.56 false

Apply battery voltage to the compressor motor and check the operation of the motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1
Motor operates


NOTICE:
·

Do not allow the motor to operate for 60 seconds or more.

·

If the height control pump and motor is shorted, locked, or has a similar type of malfunction, a large amount of current will be flowing. Therefore, if the motor does not operate, immediately stop this inspection.






OK

5.INSPECT FLUID LINE

NG

REPLACE HEIGHT CONTROL PUMP AND MOTOR

5.INSPECT FLUID LINE
a.

Check if the fluid line is clogged.

HINT:
·

Check if the fluid line that connects the height control pump and motor and No. 1 height control valve is clogged. If it is not clogged, there probably is foreign matter clogging the interior of the No. 1 height control valve.

·

Follow the removal and installation procedures for each part, as all parts need to be removed.





OK

REPLACE SUSPENSION CONTROL ECU

NG

REPAIR OR REPLACE CLOGGED PARTS