Home › Suspension › FRONT SUSPENSION › FRONT UPPER SUSPENSION ARM › 2014.08–2015.08
RM2660E _53 Suspension _052815 FRONT SUSPENSION _0255384 FRONT UPPER SUSPENSION ARM A

FRONT SUSPENSION  FRONT UPPER SUSPENSION ARM  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedures for the RH side and LH side.

·

The procedures listed below are for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 48630 1.TEMPORARILY INSTALL FRONT SUSPENSION UPPER ARM ASSEMBLY LH

C173477

a.

Temporarily install the suspension upper arm with the 2 washers, bolt and nut.

HINT:

After stabilizing the suspension, tighten the nut.



Hide 43212 2.CONNECT STEERING KNUCKLE LH

a.

Connect the steering knuckle to the suspension upper arm.


b.

Install a new nut and a new cotter pin.

Torque:
110 N*m (1122 kgf*cm, 81 ft.*lbf)

NOTICE:

If the holes for the cotter pin are not aligned, tighten the nut further up to 60°.



Hide 89516 3.CONNECT SKID CONTROL SENSOR WIRE

C173472E05
0.948,0.354 0.698,0.354 0.698,0.354 0.698,1.083 true 0.594,2.542 0.354,2.542 0.354,2.542 0.354,3.865 true 0.99,0.271 1.917,0.604 0.927,0.333 10 true Upper Arm 0.625,2.438 1.771,2.823 1.146,0.385 10 true Steering Knuckle

a.

Connect the sensor wire to the steering knuckle and upper arm with the bolt and nut.

Torque:
13 N*m (133 kgf*cm, 9.6 ft.*lbf)


Hide 48630 5.TIGHTEN FRONT SUSPENSION UPPER ARM ASSEMBLY LH

a.

Tighten the nut.

Torque:
185 N*m (1886 kgf*cm, 136 ft.*lbf)

NOTICE:

Perform this procedure with all 4 wheels on the ground.



Hide 89406 6.INSTALL FRONT HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ Active Height Control)

Hide 53785B 7.INSTALL FRONT FENDER APRON TRIM PACKING D

a.
C178878

Install the apron trim packing with the 4 clips.


Hide 53783 8.INSTALL FRONT FENDER APRON TRIM PACKING B (w/ KDSS)

a.
C173475

Install the apron trim packing with the 3 clips.


Hide 53783 9.INSTALL FRONT FENDER APRON TRIM PACKING B (w/o KDSS)

a.
C173474

Install the apron trim packing with the 4 clips.


Hide 10.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Active Height Control)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 11.PERFORM VEHICLE HEIGHT OFFSET CALIBRATION (w/ Active Height Control)

a.

Perform the vehicle height offset calibration (See page Suspension>SUSPENSION CONTROL>ACTIVE HEIGHT CONTROL SUSPENSION>INITIALIZATION).


Hide 89406 12.ADJUST FRONT HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ Active Height Control)

Hide 13.PERFORM ZERO POINT CALIBRATION OF G SENSOR (w/ Active Height Control)

a.

Perform the zero point calibration of G sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION ).


Hide 48860D 15.CLOSE STABILIZER CONTROL WITH ACCUMULATOR HOUSING SHUTTER VALVE (w/ KDSS)

Hide 48826D 16.INSTALL STABILIZER CONTROL VALVE PROTECTOR (w/ KDSS)

Hide 17.ADJUST HEADLIGHT ASSEMBLY