Use the same procedures for the RH side and LH side.
The procedures listed below are for the LH side.
A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).
1.TEMPORARILY INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING
Temporarily install the upper side of the shock absorber to the chassis frame with the 4 nuts.
Temporarily install the lower side of the shock absorber to the lower suspension arm with the bolt and nut.
49162B
2.CONNECT NO. 2 SUSPENSION CONTROL PRESSURE HOSE (w/ Active Height Control)
Apply MP grease to the O-ring and back -up ring of the suspension control pressure hose.
Connect the suspension control pressure hose to the shock absorber with the 2 bolts.
Do not allow any foreign matter such as dirt and dust to enter the suspension control pressure hose from the connecting point.
3.BLEED AIR FROM SUSPENSION FLUID (w/ Active Height Control)
4.CHECK FLUID LEVEL IN RESERVOIR (w/ Active Height Control)
5.INSPECT FOR SUSPENSION FLUID LEAK (w/ Active Height Control)
43212
6.CONNECT STEERING KNUCKLE LH
89516
7.CONNECT SKID CONTROL SENSOR WIRE
53785B
8.INSTALL FRONT FENDER APRON TRIM PACKING D (w/ Active Height Control)
Install the apron trim packing with the 4 clips.
53783
9.INSTALL FRONT FENDER APRON TRIM PACKING B (w/ Active Height Control)
Install the apron trim packing with the 4 clips.
48820B
10.TEMPORARILY INSTALL FRONT STABILIZER LINK ASSEMBLY RH
Temporarily install the stabilizer link with the bolt.
Temporarily install the stabilizer link with the nut.
Tighten the nut.
48810
11.TEMPORARILY INSTALL FRONT STABILIZER LINK ASSEMBLY LH (w/ KDSS)
Temporarily install the stabilizer link to the lower arm with the bolt.
Temporarily install the stabilizer link to the stabilizer control arm with the bolt and nut.
If the front stabilizer control cylinder extends and it is difficult to temporarily install the stabilizer link to the stabilizer control arm, raise the stabilizer control arm with a jack and temporarily install the stabilizer link.
48810
12.TEMPORARILY INSTALL FRONT STABILIZER LINK ASSEMBLY LH (w/o KDSS)
Temporarily install the stabilizer link with the nut and bolt.
Tighten the nut.
T = 128 N*m{ 1305 kgf*cm }
48829A
13.TIGHTEN FRONT NO. 1 STABILIZER BRACKET LH
Tighten the 2 bolts of the front stabilizer brackets.
Tighten the bolts in 3 steps, in the order shown in the illustration.
48824A
14.TIGHTEN FRONT NO. 1 STABILIZER BRACKET RH
Tighten the 2 bolts of the front stabilizer brackets.
Tighten the bolts in 3 steps, in the order shown in the illustration.
51405A
15.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
53806
16.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH
53805
17.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH
18.STABILIZE SUSPENSION
Install the front wheels.
Lower the vehicle.
Press down on the vehicle several times to stabilize the suspension.
19.TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING
Tighten the nut.
Perform this procedure with all 4 wheels on the ground.
Tighten the 4 upper nuts in diametrically opposite pairs.
Check that the first nut that was tightened is at the torque specification.
48810
20.TIGHTEN FRONT STABILIZER LINK ASSEMBLY LH (w/ KDSS)
Tighten the bolt.
Tighten the nut.
Perform this procedure with all 4 wheels on the ground.
48810
21.TIGHTEN FRONT STABILIZER LINK ASSEMBLY LH (w/o KDSS)
Tighten the bolt.
Perform this procedure with all 4 wheels on the ground.
48820B
22.TIGHTEN FRONT STABILIZER LINK ASSEMBLY RH
Tighten the bolt.
Perform this procedure with all 4 wheels on the ground.
23.PERFORM VEHICLE HEIGHT OFFSET CALIBRATION (w/ Active Height Control)
Perform the vehicle height offset calibration (See page Suspension>SUSPENSION CONTROL>ACTIVE HEIGHT CONTROL SUSPENSION>INITIALIZATION).
24.MEASURE VEHICLE HEIGHT (w/ KDSS)
48860D
25.CLOSE STABILIZER CONTROL WITH ACCUMULATOR HOUSING SHUTTER VALVE (w/ KDSS)
48826D
26.INSTALL STABILIZER CONTROL VALVE PROTECTOR (w/ KDSS)