Home › Suspension › SUSPENSION CONTROL › STABILIZER CONTROL VALVE(w/ KDSS) › 2014.08–2015.08
RM2660E _53 Suspension _052813 SUSPENSION CONTROL _0255376 STABILIZER CONTROL VALVE(w/ KDSS) A

SUSPENSION CONTROL  STABILIZER CONTROL VALVE(w/ KDSS)  INSTALLATION  


PROCEDURE

Hide 48860A 1.INSTALL STABILIZER CONTROL WITH ACCUMULATOR HOUSING ASSEMBLY

C172273

a.

Install the stabilizer control with accumulator housing with the 2 bolts.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


b.
C172321

Install the bleeder plug.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)

HINT:

The bleeder plug cap will be installed after bleeding air.



Hide 48880A 2.CONNECT REAR NO. 2 STABILIZER CONTROL TUBE ASSEMBLY

C174410

a.

Connect the rear No. 2 stabilizer control tube to the stabilizer control with accumulator housing.


Hide 48880 3.TEMPORARILY INSTALL REAR NO. 1 STABILIZER CONTROL TUBE ASSEMBLY

a.
C180033

Temporarily install the rear No. 1 stabilizer control tube to the stabilizer control with accumulator housing.


b.
C180032

Install the bolt to the vehicle.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 48890A 4.TEMPORARILY INSTALL FRONT NO. 2 STABILIZER CONTROL TUBE ASSEMBLY

a.
C180034

Temporarily install the front No. 2 stabilizer control tube to the front No. 1 stabilizer control tube.


b.

Install the bolt to the vehicle.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 48890A 5.TEMPORARILY INSTALL FRONT NO. 2 AND REAR NO. 1 STABILIZER CONTROL TUBE ASSEMBLY

a.

Temporarily install the front No. 2 and rear No. 1 stabilizer control tube to the 2 stabilizer control adapters.

C174144E01
1.172,3.001 2.829,3.319 1.657,0.319 10 Stabilizer Control Adapter for Lower Chamber Side 5.04,2.916 6.697,3.235 1.657,0.319 10 Stabilizer Control Adapter for Upper Chamber Side 5.18,2.15 5.717,2.532 false 5.715,2.528 5.715,2.864 false 0.33,0.673 1.689,0.995 1.360,0.322 10 Front No. 2 Stabilizer Control Tube 3.042,0.384 5.214,0.558 2.172,0.174 10 Rear No. 1 Stabilizer Control Tube 2.834,2.241 1.995,2.605 false 1.995,2.605 1.995,2.961 false 2.416,1.663 2.416,0.738 false 2.416,0.738 1.717,0.738 false 2.05,0.738 2.05,1.737 false 5.238,0.472 5.83,0.472 false 5.83,0.472 5.83,1.406 false 5.604,0.472 5.604,1.149 false


Hide 6.INSTALL STABILIZER CONTROL ADAPTER SUB-ASSEMBLY

C178418E01
0.081,1.467 1.702,1.785 1.621,0.317 10 Stabilizer Control Adapter for Lower Chamber Side 1.738,1.548 2.201,1.548 false 2.201,1.548 2.558,1.649 false 5.168,1.913 6.775,2.263 1.607,0.350 10 Stabilizer Control Adapter for Upper Chamber Side 5.124,1.985 4.838,1.985 false 4.838,1.985 4.532,1.521 false

a.

Install the 2 stabilizer control adapters to the vehicle with the 2 bolts.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


Hide 48880 7.TIGHTEN REAR NO. 1 STABILIZER CONTROL TUBE ASSEMBLY

C172320E01
2.294,1.893 3.373,2.063 1.079,0.170 10 Fulcrum Length 2.67,0.795 3.847,0.958 1.177,0.163 10 Union Nut Wrench 1.562,1.135 2.175,0.867 false 2.175,0.867 2.637,0.867 false 4.128,0.146 6.117,0.302 1.989,0.156 10 Stabilizer Control Adapter Side: 5.308,1.962 6.387,2.131 1.079,0.170 10 Fulcrum Length 5.496,0.74 6.673,0.903 1.177,0.163 10 Union Nut Wrench 4.5,1.476 5.213,0.813 false 5.214,0.81 5.466,0.81 false 0.531,0.035 2.236,0.361 1.705,0.327 10 Stabilizer Control with Accumulator Housing Side:

a.

Using a union nut wrench, tighten the rear No. 1 stabilizer control tube.

Torque:
without union nut wrench : 44 N*m (450 kgf*cm, 33 ft.*lbf)
with union nut wrench : 40 N*m (408 kgf*cm, 30 ft.*lbf)

HINT:
·

Use a torque wrench with a fulcrum length of 300 mm (11.8 in.).

·

The torque value for use with a union nut wrench is effective when the union nut wrench is parallel to the torque wrench.




Hide 48890A 8.TIGHTEN FRONT NO. 2 STABILIZER CONTROL TUBE ASSEMBLY

C172328E01
0.978,0.25 3.536,0.420 2.559,0.170 10 Front No. 1 Stabilizer Control Tube Side: 4.341,0.24 6.358,0.424 2.017,0.184 10 Stabilizer Control Adapter Side: 0.481,2.209 1.582,2.365 1.100,0.156 10 Fulcrum Length 4.615,2.79 5.715,2.946 1.100,0.156 10 Fulcrum Length 2.668,1.966 3.851,2.150 1.184,0.184 10 Union Nut Wrench 2.296,1.514 2.483,2.048 false 2.483,2.048 2.635,2.048 false 5.816,1 6.999,1.183 1.184,0.184 10 Union Nut Wrench 5.1,1.224 5.478,1.07 false 5.477,1.071 5.784,1.071 false

a.

Using a union nut wrench, tighten the front No. 2 stabilizer control tube.

Torque:
without union nut wrench : 44 N*m (450 kgf*cm, 33 ft.*lbf)
with union nut wrench : 40 N*m (408 kgf*cm, 30 ft.*lbf)

HINT:
·

Use a torque wrench with a fulcrum length of 300 mm (11.8 in.).

·

The torque value for use with a union nut wrench is effective when the union nut wrench is parallel to the torque wrench.




Hide 48880A 9.TIGHTEN REAR NO. 2 STABILIZER CONTROL TUBE ASSEMBLY

a.
C172289E02
2,1.083 2.552,1.375 true 2.542,1.365 2.542,1.677 true 0.229,2.021 1.229,2.375 1,0.354 10 true Fulcrum Length 1.823,1.688 3.063,1.99 1.24,0.302 10 true Union Nut Wrench

Using a union nut wrench, tighten the rear No. 2 stabilizer control tube.

Torque:
without union nut wrench : 44 N*m (450 kgf*cm, 33 ft.*lbf)
with union nut wrench : 40 N*m (408 kgf*cm, 30 ft.*lbf)

HINT:
·

Use a torque wrench with a fulcrum length of 300 mm (11.8 in.).

·

The torque value for use with a union nut wrench is effective when the union nut wrench is parallel to the torque wrench.




Hide 17420 10.INSTALL CENTER EXHAUST PIPE ASSEMBLY

a.

for 1GR-FE:

Install the center exhaust pipe (See page Engine / Hybrid System>1GR-FE (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION).


b.

for 1UR-FE:

Install the center exhaust pipe (See page Engine / Hybrid System>1UR-FE (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION).


c.

for 3UR-FE:

Install the center exhaust pipe (See page Engine / Hybrid System>3UR-FE (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION).


d.

for 1VD-FTV:

Install the center exhaust pipe (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST PIPE(w/o DPF)>INSTALLATION).


Hide 17430 11.INSTALL TAILPIPE ASSEMBLY

Hide 12.BLEED AIR FROM SUSPENSION FLUID

a.

Bleed the air from the suspension fluid (See page Suspension>SUSPENSION CONTROL>SUSPENSION CONTROL SYSTEM (w/ KDSS)>BLEEDING).


Hide 14.INSPECT FOR EXHAUST GAS LEAK

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.


Hide 48860D 16.CLOSE STABILIZER CONTROL WITH ACCUMULATOR HOUSING SHUTTER VALVE

NOTICE:
·

Perform the inspection on a level surface.

·

Ensure that the wheels are on the ground and facing straight ahead.

·

Perform the inspection with the vehicle load completely on the suspension.



HINT:
·

Perform this step with the fuel tank full.

·

If there are any parts installed to the vehicle which place any unbalanced load on the left or right side of the vehicle, remove them.



a.

Using a 5 mm hexagon socket wrench, tighten the lower and upper chamber shutter valves of the stabilizer control with accumulator housing.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 48826D 17.INSTALL STABILIZER CONTROL VALVE PROTECTOR

C172095

a.

Install the valve protector with the 3 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Attach the clamp, and connect the connector to the valve protector.