Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2014.08–2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Brake Warning Light Remains ON  


DESCRIPTION

The brake warning light comes on when brake fluid is insufficient, the parking brake is applied or the EBD is defective.

WIRING DIAGRAM

C258218E02
3.604,2.073 4.063,2.302 0.458,0.229 10 false PKB 2.896,2.281 3.333,2.552 0.438,0.271 10 false 22 3.208,4.281 3.615,4.49 0.406,0.208 10 false E53 3.208,4.479 4.583,4.875 1.375,0.396 10 false Parking Brake Switch Assembly 3.229,3.844 3.542,4.073 0.313,0.229 10 false 1 3,2.688 3.313,2.875 0.313,0.188 10 false 2D 3,2.865 4.583,3.281 1.583,0.417 10 false Main Body ECU (Cowl Side Junction Block LH) 5.385,4.229 5.74,4.448 0.354,0.219 10 false A24 5.365,4.417 7.063,4.917 1.698,0.5 10 false Skid Control ECU (Master Cylinder Solenoid) 0.302,4.406 0.677,4.625 0.375,0.219 10 false E7 0.302,4.573 2.167,4.813 1.865,0.24 10 false Combination Meter Assembly 0.76,5.167 2.823,5.385 2.063,0.219 10 false : CAN Communication System

CAUTION / NOTICE / HINT

NOTICE:

After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK DTC
a.

Check for DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

2.INSPECT IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

B

2.INSPECT IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

OK

3.INSPECT BATTERY

NG

CONNECT CONNECTOR TO ECU CORRECTLY

4.CHECK CAN COMMUNICATION LINE

A

5.CHECK DTC (CAN COMMUNICATION SYSTEM)

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

5.CHECK DTC (CAN COMMUNICATION SYSTEM)

A

6.PERFORM ACTIVE TEST USING GTS (INDICAT. LAMP BRAKE)

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

6.PERFORM ACTIVE TEST USING GTS (INDICAT. LAMP BRAKE)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Check the condition of the brake warning light by operating the GTS.

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Indicat. Lamp Brake Brake Warning Light ON or OFF Perform the test with the vehicle stopped and engine idling.

OK:

The warning light turns on when operating the GTS.




OK

7.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

NG

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

7.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

OK

8.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

OK

9.INSPECT PARKING BRAKE SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT PARKING BRAKE SWITCH
a.
C215408E03
0.24,0.167 0.573,0.385 0.333,0.219 10 false *a

Disconnect the E53 parking brake switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - Body ground Parking brake applied
(Switch pin free)
Below 1 Ω
Parking brake released
(Switch pin pushed in)
10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Parking Brake Switch Assembly)



OK

10.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - PARKING BRAKE SWITCH)

NG

REPLACE PARKING BRAKE SWITCH ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - PARKING BRAKE SWITCH)
a.

Turn the ignition switch off.


b.

Disconnect the E53 parking brake switch connector.


c.

Disconnect the 2D main body ECU (cowl side junction block LH) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2D-22 - E53-1 Always Below 1 Ω
2D-22 - Body ground Always 10 kΩ or higher




OK

11.PERFORM ACTIVE TEST USING GTS (BRAKE WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.PERFORM ACTIVE TEST USING GTS (BRAKE WARNING LIGHT)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Brake Warning Light Brake warning light Warning light ON/OFF Observe the combination meter.


f.

When performing the Brake Warning Light Active Test, check Brake Warning Light in the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Brake Warning Light Brake warning light/ ON or OFF ON: Warning light on
OFF: Warning light off
-

Result
Result Proceed to
Data List Display Data List Display when Performing Active Test ON/OFF Operation
ON Changes between ON and OFF A
Does not change between ON and OFF (for LHD) B
Does not change between ON and OFF (for RHD) C
OFF Changes between ON and OFF A
Does not change between ON and OFF (for LHD) B
Does not change between ON and OFF (for RHD) C



A

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

B

C