Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2014.08–2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1251  Open in Pump Motor Circuit  


DESCRIPTION

The motor relay (semiconductor relay) is built into the master cylinder solenoid and drives the pump motor based on a signal from the skid control ECU (master cylinder solenoid).

DTC Code DTC Detection Condition Trouble Area
C1251 There is an open in the motor system circuit (motor input circuit).
·

Pump motor wire harness connection

·

Brake booster with accumulator pump assembly

·

Skid control ECU (Master cylinder solenoid)



CAUTION / NOTICE / HINT

NOTICE:

After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


HINT:

Remove the hydraulic brake booster assembly before the inspection (for LHD: See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for LHD)>ON-VEHICLE INSPECTION, for RHD: See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for RHD)>ON-VEHICLE INSPECTION).


PROCEDURE

1.CHECK CONNECTION OF PUMP MOTOR WIRE HARNESS
a.

b.

Check the tightening torque of the 2 screws which secure the wire harness connecting the master cylinder solenoid and brake booster with accumulator pump assembly (for LHD: See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for LHD)>REASSEMBLY, for RHD: See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for RHD)>REASSEMBLY).


OK:

The harness is tightened to the specified torque.



OK

2.CHECK RESISTANCE OF PUMP MOTOR WIRE HARNESS

NG

RETIGHTEN SCREWS

2.CHECK RESISTANCE OF PUMP MOTOR WIRE HARNESS
a.

Using a screwdriver, remove the 2 screws and pull out the wire harness from the master cylinder solenoid.


b.
C173363E10
1.542,1.417 0.896,0.75 0.896,0.75 0.719,0.75 true 1.385,1.458 0.885,1.771 0.885,1.771 0.719,1.771 false 1.594,1.813 2.104,0.844 2.104,0.844 2.292,0.844 false 0.469,0.656 0.688,0.844 0.219,0.188 10 false *a 0.469,1.677 0.667,1.885 0.198,0.208 10 false *b 2.365,0.76 2.604,0.938 0.24,0.177 10 false *1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Red wire terminal - Black wire terminal Always Below 2 Ω


Text in Illustration
*1 Pump motor wire harness
*a Red wire
*b Black wire


HINT:
Refer to the brake booster with accumulator pump assembly installation procedures:



OK

3.RECONFIRM DTC

NG

REPLACE BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY

3.RECONFIRM DTC
a.



d.

Turn the ignition switch off.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

C