Home › Brake › BRAKE SYSTEM (OTHER) › HYDRAULIC BRAKE BOOSTER(for RHD)
RM2660E _54 Brake _052820 BRAKE SYSTEM (OTHER) _0255427 HYDRAULIC BRAKE BOOSTER(for RHD) A

BRAKE SYSTEM (OTHER)  HYDRAULIC BRAKE BOOSTER(for RHD)  INSTALLATION  


PROCEDURE

Hide 44785 1.INSTALL BRAKE BOOSTER GASKET

a.

Install a new brake booster gasket to the hydraulic brake booster.


Hide 2.INSTALL HYDRAULIC BRAKE BOOSTER ASSEMBLY

a.
C172861

Install the hydraulic brake booster assembly with the 4 nuts.

Torque:
14 N*m (145 kgf*cm, 10 ft.*lbf)


b.
F051200E14
1.198,1.167 1.198,0.74 1.198,0.74 0.698,0.74 true 1.594,1.521 1.594,0.104 1.594,0.104 1.281,0.104 true 2.042,1.729 2.302,0.135 2.302,0.135 2.385,0.135 true 2.479,1.823 2.688,0.896 2.688,0.896 2.802,0.896 true 0.031,0.646 0.802,1.021 0.771,0.375 10 true to Right Rear Wheel 0.583,0.01 1.396,0.396 0.813,0.385 10 true to Right Front Wheel 2.438,0.031 3.24,0.406 0.802,0.375 10 true to Left Front Wheel 2.844,0.813 3.365,1.365 0.521,0.552 10 true to Left Rear Wheel

Connect the 4 brake lines to the correct positions of the hydraulic brake booster assembly as shown in the illustration.


c.
C179353E02
1.104,1.448 1.552,1.052 1.552,1.052 2.375,1.052 true 0.219,1.875 1.24,2.115 1.021,0.24 10 true Fulcrum Length 2.438,0.979 3.125,1.344 0.688,0.365 10 true Union Nut Wrench

Install the clamp with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


d.

Using a union nut wrench, tighten the 4 brake lines.

Torque:
without union nut wrench : 15 N*m (155 kgf*cm, 11 ft.*lbf)
with union nut wrench : 14 N*m (145 kgf*cm, 10 ft.*lbf)

HINT:
·

Use a torque wrench with a fulcrum length of 300 mm (11.8 in.).

·

The torque value for use with a union nut wrench is effective when the union nut wrench is parallel to the torque wrench.




e.
C172863

Connect the 3 connectors to the hydraulic brake booster.


Hide 55432D 5.INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

Hide 55606 7.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 9.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 47217 14.INSPECT BRAKE MASTER CYLINDER OPERATION

a.

Inspect the brake master cylinder operation (See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for RHD)>ON-VEHICLE INSPECTION).