Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Turn Assist Indicator Light Circuit  


DESCRIPTION

When any of the following conditions are met, the turn assist system becomes operable and the turn assist indicator light illuminates.

·

Crawl Control is operating.

·

The turn assist function switch (suspension control switch)*1 or turn assist function switch (integration control and panel assembly)*2 is on.

*1: w/o Entry and Start System

*2: w/ Entry and Start System

·

The center differential is "free".

·

The vehicle is moving at a speed of 10 km/h (6 mph) or less.

·

The shift lever is not in P, R or N.


WIRING DIAGRAM

C256733E27
5.135,2.604 6.854,3.073 1.719,0.469 10 false Skid Control ECU (Master Cylinder Solenoid) 5.135,2.438 5.49,2.688 0.354,0.25 10 false A24 2.531,1.813 2.885,2 0.354,0.188 10 false V4*1 2.917,1.813 3.292,2.021 0.375,0.208 10 false V8*2 2.51,2 5.104,2.365 2.594,0.365 10 false Turn Assist Function Switch (Suspension Control Switch)*1 2.521,2.396 5.052,2.76 2.531,0.365 10 false Turn Assist Function Switch (Integration Control and Panel Assembly)*2 0.25,2.531 0.792,2.75 0.542,0.219 10 false E119 0.24,2.698 2.167,3.052 1.927,0.354 10 false Combination Meter Assembly 2.719,3.385 4.896,3.573 2.177,0.188 10 false *1: w/o Entry and Start System 4.875,3.385 7.052,3.573 2.177,0.188 10 false *2: w/ Entry and Start System 5.344,1.51 5.813,1.688 0.469,0.177 10 false EXI4 5.063,1.375 5.24,1.563 0.177,0.188 10 false 29 4.094,1.417 4.365,1.604 0.271,0.188 10 false 2*1 4.063,1.25 4.49,1.438 0.427,0.188 10 false 12*2 2.635,1.417 3.01,1.604 0.375,0.188 10 false 16*1 2.625,1.24 3,1.417 0.375,0.177 10 false 10*2 0.542,3.26 2.521,3.542 1.979,0.281 10 false : CAN Communication System 3.719,1.417 4.042,1.625 0.323,0.208 10 false ECU 3.031,1.417 3.208,1.594 0.177,0.177 10 false E

CAUTION / NOTICE / HINT

NOTICE:

After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

2.CHECK DTC (CAN COMMUNICATION SYSTEM)

A

3.INSPECT SUSPENSION CONTROL SWITCH OR INTEGRATION CONTROL AND PANEL ASSEMBLY

B

C

D

E

3.INSPECT SUSPENSION CONTROL SWITCH OR INTEGRATION CONTROL AND PANEL ASSEMBLY
a.

w/o Entry and Start System:

Remove the turn assist function switch (suspension control switch) (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>CRAWL SWITCH(w/o Entry and Start System)>REMOVAL).


b.

w/ Entry and Start System:

Remove the turn assist function switch (integration control and panel assembly) (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>CRAWL SWITCH(w/ Entry and Start System)>REMOVAL).


c.

w/o Entry and Start System:

Inspect the turn assist function switch (suspension control switch) (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>CRAWL SWITCH(w/o Entry and Start System)>INSPECTION).


d.

w/ Entry and Start System:

Inspect the turn assist function switch (integration control and panel assembly) (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>CRAWL SWITCH(w/ Entry and Start System)>INSPECTION).


Result
Result Proceed to
OK A
NG (w/o Entry and Start System) B
NG (w/ Entry and Start System) C


A

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - TURN ASSIST FUNCTION SWITCH)

B

C

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - TURN ASSIST FUNCTION SWITCH)
a.

Turn the ignition switch off.


b.

Disconnect the A24 skid control ECU (master cylinder solenoid) connector.


c.

Disconnect the V4 turn assist function switch (suspension control switch)*1 or V8 turn assist function switch (integration control and panel assembly)*2 connector.

*1: w/o Entry and Start System

*2: w/ Entry and Start System



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Entry and Start System:
Tester Connection Condition Specified Condition
A24-29 (EXI4) - V4-2 (ECU) Always Below 1 Ω
A24-29 (EXI4) - Body ground Always 10 kΩ or higher
V4-16 (E) - Body ground Always Below 1 Ω

w/ Entry and Start System:
Tester Connection Condition Specified Condition
A24-29 (EXI4) - V8-12 (ECU) Always Below 1 Ω
A24-29 (EXI4) - Body ground Always 10 kΩ or higher
V8-10 (E) - Body ground Always Below 1 Ω

Result
Result Proceed to
OK (w/o Entry and Start System) A
OK (w/ Entry and Start System) B
NG C




A

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU EXI4 CIRCUIT)

B

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU EXI4 CIRCUIT)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU EXI4 CIRCUIT)
a.

Turn the ignition switch off.


b.

Connect the skid control ECU (master cylinder solenoid) connector.


c.
U165791E02
1.156,1.385 0.604,1.385 true 0.156,0.125 0.427,0.333 0.271,0.208 10 false *a 1.594,0.604 1.823,0.771 0.229,0.167 10 false V4 0.26,1.313 0.635,1.531 0.375,0.219 10 false ECU

Disconnect the turn assist function switch (suspension control switch) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
V4-2 (ECU) - Body ground Ignition switch ON 11 to 14 V


*a Front view of wire harness connector
(to Turn Assist Function Switch [Suspension Control Switch])



OK

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU EXI4 CIRCUIT)
a.

Turn the ignition switch off.


b.

Connect the skid control ECU (master cylinder solenoid) connector.


c.
U165679E02
0.563,1.302 1.625,1.448 true 0.135,0.104 0.427,0.323 0.292,0.219 10 false *a 0.198,1.229 0.615,1.448 0.417,0.219 10 false ECU 1.646,0.208 1.969,0.406 0.323,0.198 10 false V8

Disconnect the turn assist function switch (integration control and panel assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
V8-12 (ECU) - Body ground Ignition switch ON 11 to 14 V


*a Front view of wire harness connector
(to Turn Assist Function Switch [Integration Control and Panel Assembly])

Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

B

C