Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2014.08–2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255416 ANTI-LOCK BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  Brake Warning Light Remains ON  


DESCRIPTION

The brake warning light comes on when brake fluid is insufficient, the parking brake is applied or the EBD is defective.

WIRING DIAGRAM

C258218E02
3.604,2.073 4.063,2.302 0.458,0.229 10 false PKB 2.896,2.281 3.333,2.552 0.438,0.271 10 false 22 3.208,4.281 3.615,4.49 0.406,0.208 10 false E53 3.208,4.479 4.583,4.875 1.375,0.396 10 false Parking Brake Switch Assembly 3.229,3.844 3.542,4.073 0.313,0.229 10 false 1 3,2.688 3.313,2.875 0.313,0.188 10 false 2D 3,2.865 4.583,3.281 1.583,0.417 10 false Main Body ECU (Cowl Side Junction Block LH) 5.385,4.229 5.74,4.448 0.354,0.219 10 false A24 5.365,4.417 7.063,4.917 1.698,0.5 10 false Skid Control ECU (Master Cylinder Solenoid) 0.302,4.406 0.677,4.625 0.375,0.219 10 false E7 0.302,4.573 2.167,4.813 1.865,0.24 10 false Combination Meter Assembly 0.76,5.167 2.823,5.385 2.063,0.219 10 false : CAN Communication System

CAUTION / NOTICE / HINT

NOTICE:

After replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK DTC
a.

Check for DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

2.CHECK CAN COMMUNICATION LINE

B

2.CHECK CAN COMMUNICATION LINE

A

3.READ VALUE USING GTS (PARKING BRAKE SW)

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

3.READ VALUE USING GTS (PARKING BRAKE SW)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Parking Brake SW Parking brake switch/ ON or OFF ON: Parking brake applied
OFF: Parking brake released
-


f.

Using the GTS, check the input of the switch operation when the parking brake pedal is operated.

OK:

When the parking brake is operated, the display changes as shown above.




OK

4.PERFORM ACTIVE TEST USING GTS (BRAKE WARNING LIGHT)

NG

5.INSPECT PARKING BRAKE SWITCH
4.PERFORM ACTIVE TEST USING GTS (BRAKE WARNING LIGHT)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Brake Warning Light Brake warning light Warning light ON/OFF Observe the combination meter.


f.

When performing the Brake Warning Light Active Test, check Brake Warning Light in the Data.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Brake Warning Light Brake warning light/ ON or OFF ON: Warning light on
OFF: Warning light off
-

Result
Result Proceed to
Data List Display Data List Display when Performing Active Test ON/OFF Operation
ON Changes between ON and OFF A
Does not change between ON and OFF (for LHD) B
Does not change between ON and OFF (for RHD) C
OFF Changes between ON and OFF A
Does not change between ON and OFF (for LHD) B
Does not change between ON and OFF (for RHD) C



A

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

B

C

5.INSPECT PARKING BRAKE SWITCH
a.

Disconnect the E53 parking brake switch connector.


b.
C215408E03
0.24,0.167 0.573,0.385 0.333,0.219 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - Body ground Parking brake applied
(Switch pin not pushed in)
Below 1 Ω
Parking brake released
(Switch pin pushed in)
10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Parking Brake Switch)



OK

6.CHECK HARNESS AND CONNECTOR (PARKING BRAKE SWITCH - MAIN BODY ECU)

NG

REPLACE PARKING BRAKE SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (PARKING BRAKE SWITCH - MAIN BODY ECU)
a.

Disconnect the E53 parking brake switch connector.


b.

Disconnect the 2D main body ECU (cowl side junction block LH).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E53-1 - 2D-22 Always Below 1 Ω
E53-1 - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR