Home › Steering › VARIABLE GEAR RATIO STEERING › VARIABLE GEAR RATIO STEERING SYSTEM › from 2015.08
RM2660E _55 Steering _052825 VARIABLE GEAR RATIO STEERING _0255448 VARIABLE GEAR RATIO STEERING SYSTEM J

VARIABLE GEAR RATIO STEERING  VARIABLE GEAR RATIO STEERING SYSTEM  VGRS System Stops or does not Operate  


CAUTION / NOTICE / HINT

NOTICE:

When replacing the steering actuator assembly, perform actuator angle neutral point calibration and initialization after replacement (See page Steering>VARIABLE GEAR RATIO STEERING>VARIABLE GEAR RATIO STEERING SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs (See page Steering>VARIABLE GEAR RATIO STEERING>VARIABLE GEAR RATIO STEERING SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

2.READ VALUE USING GTS (ABNORMAL OPERATION HISTORY)

B

2.READ VALUE USING GTS (ABNORMAL OPERATION HISTORY)
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / VGRS / Data List.


f.

According to the display on the GTS, read the Abnormal Operation History.

VGRS
Tester Display Measurement Item/Range Diagnostic Note
Limited Control Count(Overheat-Weak) Limited control count (overheat-weak)/
Min.: 0
Max.: 255
The number of times that overheat status of VGRS became "Overheat-Weak" and then the control was limited.
Limited Control Count(Overheat-Mid) Limited control count (overheat-mid)/
Min.: 0
Max.: 255
The number of times that overheat status of VGRS became "Overheat-Mid" and then the control was limited.
Limited Control Count(Overheat-Strong) Limited control count (overheat-strong)/
Min.: 0
Max.: 255
The number of times that overheat status of VGRS became "Overheat- Strong" and then the control was limited.
N Pos Stop Control Count N pos stop control count/
Min.: 0
Max.: 255
The number of times that power supply status to VGRS became "N Pos Stop" and then the control in "N Pos Stop" happened.
Cur Pos Stop Control Count Cur pos stop control count/
Min.: 0
Max.: 255
The number of times that power supply status to VGRS became "Cur Pos Stop" and then the control in "Cur Pos Stop" happened.
Prompt Stop Control Count Prompt stop control count/
Min.: 0
Max.: 255
The number of times that power supply status to VGRS became "Prompt Stop" and then the control in "Prompt Stop" happened.
Limited Control Count (System Heavily-loaded) Limited control count (system heavily-loaded)/
Min.: 0
Max.: 255
The number of times that VGRS system became heavily-loaded and then the control was limited.

Result
Result Proceed to
One of the Data List items has a count of 1 or more. A
Other than above B

HINT:

When there is a decrease or increase in power source voltage, or during overheating prevention, VGRS system operation stops temporarily.




A

3.CUSTOMER PROBLEM ANALYSIS

B

3.CUSTOMER PROBLEM ANALYSIS
a.

Check if operation stopped under harsh conditions, such as the steering wheel being repeatedly turned while the vehicle is stationary.

Result
Result Proceed to
Operation stopped under conditions that are not harsh A
Operation stopped under harsh conditions B

HINT:

When the torque load is large, such as when driving on rough roads, VGRS system operation stops to protect the system.




A

4.CHECK STEERING EFFORT

B

6.CHECK VGRS SYSTEM
4.CHECK STEERING EFFORT
a.

Check the steering torque when the steering wheel is turned with the vehicle stopped (for 1VD-FTV: See page Steering>POWER ASSIST SYSTEMS>VANE PUMP (for 1VD-FTV)>ON-VEHICLE INSPECTION, for 1UR-FE: See page Steering>POWER ASSIST SYSTEMS>VANE PUMP (for 1UR-FE)>ON-VEHICLE INSPECTION, for 3UR-FE: See page Steering>POWER ASSIST SYSTEMS>VANE PUMP (for 3UR-FE)>ON-VEHICLE INSPECTION).


OK:

The steering torque is normal.


HINT:

When the steering effort is large, VGRS system operation stops to protect the system.


Result
Result Proceed to
OK A
NG (w/ Variable Flow Control Solenoid Valve) B
NG (w/o Variable Flow Control Solenoid Valve) C


A

5.CHECK STEERING ACTUATOR ASSEMBLY

B

C

GO TO POWER STEERING SYSTEM (PROBLEM SYMPTOMS TABLE)

5.CHECK STEERING ACTUATOR ASSEMBLY
a.

Check for abnormal noise or vibration in the steering actuator assembly.


OK:

Neither abnormal noise nor vibration occurs.



OK

6.CHECK VGRS SYSTEM

NG

REPLACE STEERING ACTUATOR ASSEMBLY

6.CHECK VGRS SYSTEM
a.

Operate the steering wheel and check that the system recovers.

Result
Result Proceed to
The system recovers when the steering wheel is operated. A
The system recovers when the steering wheel is not operated. B



A

END

B

REPLACE STEERING ACTUATOR ASSEMBLY