Home › Steering › VARIABLE GEAR RATIO STEERING › VARIABLE GEAR RATIO STEERING SYSTEM › from 2015.08
RM2660E _55 Steering _052825 VARIABLE GEAR RATIO STEERING _0255448 VARIABLE GEAR RATIO STEERING SYSTEM S

VARIABLE GEAR RATIO STEERING  VARIABLE GEAR RATIO STEERING SYSTEM  DIAGNOSTIC TROUBLE CODE CHART  


HINT:

If a trouble code is output during the DTC check, inspect the trouble areas listed for that code. For details of the code, refer to the "See page" below.


Variable Gear Ratio Steering System
DTC Code Detection Item Warning Indicate Return-to-normal Condition See page
C1591/51 Actuator Neutral Position Calibration Undone Comes on Perform actuator angle neutral point calibration. (Click here)
C1592/52 Actuator Neutral Position Calibration Incomplete Comes on After clearing DTCs, perform actuator angle neutral point calibration. (Click here)
C1593/53 Actuator Standard Position Malfunction Comes on Engine switch on (IG) again (Click here)
C1595/55 Lost Communication with Steering Angle Sensor Module Comes on Engine switch on (IG) again (Click here)
C15A1/61 Actuator Malfunction Comes on Engine switch on (IG) again (Click here)
C15A2/62 Open in Motor Circuit Comes on Engine switch on (IG) again (Click here)
C15A3/63 Motor Rotation Angle Not Detected Comes on Engine switch on (IG) again (Click here)
C15A4/64 Motor Rotation Angle Malfunction Comes on Engine switch on (IG) again (Click here)
C15A5/65 Lock Mechanism Circuit Comes on Engine switch on (IG) again (Click here)
C15A6/62 Actuator Motor Power Distribution Malfunction Comes on Engine switch on (IG) again (Click here)
C15A9/66 Lock Holder Deviation Detection Comes on After clearing DTCs, perform actuator angle neutral point calibration. (Click here)
C15AA/66 Lock Mechanism Release Incomplete Comes on After clearing DTCs, perform actuator angle neutral point calibration. (Click here)
C15AB/66 Lock Mechanism Insertion Comes on After clearing DTCs, perform actuator angle neutral point calibration. (Click here)
C15B1/71 ECU Malfunction(CPU) Comes on Engine switch on (IG) again (Click here)
C15B2/72 ECU Malfunction(Internal Line) Comes on Engine switch on (IG) again (Click here)
C15B3/73 ECU Malfunction(Substrate Temperature Sensor) Does not come on Engine switch on (IG) again (Click here)
C15B4/71 ECU Malfunction(Actuator Angle Record) Comes on After clearing DTCs, perform actuator angle neutral point calibration. (Click here)
C15B5/82 ECU Malfunction(Flash Memory) Comes on Engine switch on (IG) again (Click here)
C15B6/83 ECU Malfunction(EEPROM) Comes on Engine switch on (IG) again (Click here)
C15C1/74 Steering Angle Sensor Comes on Engine switch on (IG) again (Click here)
C15C2/74 Steering Angle Sensor B+ Comes on Engine switch on (IG) again (Click here)
C15C3/75 Brake System Control Module Comes on Engine switch on (IG) again (Click here)
C15C4/68 Steering Angle Signal (Test Mode DTC) - Test mode code (Click here)
C15C5/69 Motor Rotation Signal Not Detected - Test mode code (Click here)
C15C6/77 IG Power Supply Voltage Comes on Engine switch on (IG) again (Click here)
C15C7/78 DC Motor Power Source Voltage Comes on Engine switch on (IG) again (Click here)
C15C8/79 Power Supply Relay Failure Comes on Engine switch on (IG) again (Click here)
C15CB/84 VSC System Malfunction Comes on Engine switch on (IG) again (Click here)
U0100/56 Lost Communication with ECM / PCM "A" Comes on Engine switch on (IG) again (Click here)
U0101/56 Lost Communication with TCM Comes on Engine switch on (IG) again (Click here)
U0125/56 Lost Communication with Yaw Rate Sensor Module Comes on Engine switch on (IG) again (Click here)
U0126/56 Lost Communication with Steering Angle Sensor Module Comes on Engine switch on (IG) again (Click here)
U0129/56 Lost Communication with Brake System Control Module Comes on Engine switch on (IG) again (Click here)